Skip to content

delphi unit injector repair

You search PDF repair manual about delphi unit injector repair, if there are search results will appear below. If search results do not exist, please search by others keyword.

NISSAN FUEL SENDING UNIT REPAIR MANUAL

download
Replace the Fuel Sending Unit and apply Tectyl 517 (Bitumen) Wax Sealer to the Fuel Sending Unit Mounting Flange area. • Frontier: See page 11 for the Fuel Sending Unit Replacement and Wax Sealer application procedures. • Xterra: See page 25 for the Fuel Sending Unit Replacement and Wax Sealer application procedures. NOTE: During the Fuel Sending Unit replacement procedure, you’ll be instructed to inspect the Fuel Sending Unit Mounting Flange and O-Ring Groove (on the Fuel Tank). Based on the inspection results, you may have to replace the Fuel Tank. Add a “protective coating” to the Fuel Sending Unit connectors. • Frontier: See page 10 for the Fuel Sending Unit Protective Coating procedure. • Xterra: See page 24 for the Fuel Sending Unit Protective Coating procedure. End * A visual-aid “Pocket Card” was previously supplied to each dealer. For additional or replacement Pocket Cards, call the Resolve Corporation (formerly DDS Distribution) at (562) 698-2688. The part number for the Pocket Card is

1984-1995 Honda Accord/Prelude In­Tank Fuel Pumps TEST/REPAIR MANUAL

download
Carbureted Fuel System GENERAL INFORMATION On these vehicles, the engine management system is considered part of the emission control system. The major components include the carburetor(s), feedback control system, the air injection system, a throttle control system and the EGR system. The system consists of sensors and switches that feed information to the Electronic Control Unit (ECU), which will then operate several solenoid valves to maintain the ideal air/fuel ratio under all conditions. As useful as the tests found in this section are, the first step in repair or service to engine management systems is still to gain as much information as possible about the problem; when and under what conditions it occurs. At highway speed? At idle only? Only under heavy load or hard acceleration? Wet weather? Defining the problem will eliminate many systems from consideration and possibly point to the affected system. Before diving into an extended electrical diagnosis, take the time to review the basics. Check every vacuum line for cracks or leaks. Check every electrical connector for corrosion or loose pins. Quite often, simply unplugging and reconnecting a connector will break up corrosion on the pins and restore the circuit. Watch out for poor grounds, particularly if the car has experienced major bodywork. COMPONENT TESTING Air Injection System The purpose of this system is to supply oxygen to the exhaust stream at a point in the exhaust manifold that is hot enough to burn off some of the hydrocarbon emissions. The main component is an air suction valve. The valve is spring loaded to stay closed, with engine vacuum supplied to a diaphragm that reduces the spring pressure and allows the reeds to open. The ECU regulates the engine vacuum to the diaphragm by operating a solenoid valve. 1. With the engine at normal operating temperature and at idle, remove the air cleaner and listen for a bubbling sound at the air suction port. There should be no sound at idle, meaning the air suction valve is closed. 2. If the noise is heard at the air suction port, disconnect the vacuum hose at the air suction valve and connect a vacuum gauge to the hose. There should be no vacuum. If there is vacuum and the noise stops, the problem is in the control system. If there is no vacuum and the bubbling sound is still there, the air suction valve is defective and must be replaced. 3. To test the valve, draw a vacuum at the air suction valve diaphragm and listen for a bubbling sound at the air suction port. If no sound is heard, the air suction valve or diaphragm is faulty. Throttle Control System

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

1996-2001 Honda Civic – ALL Civic Rear Main Oil Seal Leaks Repair manual

download
REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine warm up to its normal operating temperature (the cooling fan cycles twice). Let the engine idle (throttle fully closed with all electrical items turned off) for 10 minutes. 8. 2001 2-door EX and LX models only. Drive the vehicle above 40 mph for 5 to 10 minutes with the cruise control on. (This lets the cruise control actuator learn how much slack there is in the throttle cable.)