Skip to content

diagram for parking brake lever assembly for 1988 toyota 4runner

You search PDF repair manual about diagram for parking brake lever assembly for 1988 toyota 4runner, if there are search results will appear below. If search results do not exist, please search by others keyword.

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

TOYOTA Celica GT-S Front Big Brake Installation Instructions

download
Step 1 Jack up car Apply parking brake and properly block rear wheels. Break loose the lug nuts on both front wheels with a 21mm socket before jacking up the car. Make sure the jack and stand are supporting the frame rail portion of the body pan, not the flat floor pan. All Photographs Show Left Side Installation Jack Position Jack Stand Supporting Frame Rail Portion of Body Pan View of the stock left front brake assembly after wheel has been removed. NEVER LEAVE ANY VEHICLE SUPPORTED WITH ONLY A JACK, ALWAYS USE JACK STANDS. Step 2 Loosen the brake line fitting nut at the flex line using an 11mm wrench. A flare fitting wrench is preferable if available Using a pair of needle nose pliers, remove the stock clip from the hard line. Set clip aside, it will be used later when the new stainless steel lines are installed. Remove flex line fitting from standoff bracket and plug the hard line with one of the rubber plugs provided with the stainless steel line kit. This should effectively prevent fluid loss for the course of the installation. Step 3 Loosen the stock caliper mounting bolts with a 14mm wrench or socket. Remove the caliper with stock brake line attached. Be aware there may be some leakage from the open end of the brake line, but it should remain faily dry unless the pads / pistons on the caliper are retracted.

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

TOYOTA 4RUNNER A750E (F) AUTOMATIC TRANSMISSION SERVICE MANUAL

download
The ATF level gauge (dip-stick) has been discontinued, and the ATF inspection method and the oil level inspection method have been changed. This mechanism consists of a refill plug, overflow plug, ATF temperature sensor No.2, and A/T OIL TEMP temperature warning light. ATF Filling procedures using SST (09843-18020): When a large amount of ATF needs to be filled (i.e. after removal and installation of oil pan or torque converter), perform the procedure from step 1. When the small amount of ATF is required (i.e. removal and installation of the oil cooler tube, repair of oil leak), perform the procedure from step 7. 1) Raise the vehicle keeping it level. 2) Remove the refill plug and overflow plug. 3) Fill ATF from the refill plug until it overflows from the overflow plug. 4) Install the overflow plug. 5) Fill the specified amount of ATF determined by procedure and install the refill plug. Example 6) Lower the vehicle down. 7) Use the SST (09843-18020) to short the terminals Tc and CG of the DLC3 connector: 8) Start the engine and allow it to idle. A/C switch must be turned OFF. 9) Move the shift lever slowly through each of the positions from the P to the L position, and move it back to the P position. 10) Move the shift lever from the D position, and quickly move then back and forth between N and D (once per less than 1.5 seconds) for at least 6 seconds. This will activate the oil temperature detection mode. Standard: The A/T OIL TEMP warning light remains illuminated for 2 seconds and it goes off. 11) Return the shift lever to the P position and disconnect the terminal Tc. 12) Idle the engine to raise the oil temperature. 13) Immediately after the ATF OIL TEMP warning light turns on, lift the vehicle up. The A/T OIL TEMP warning light will indicate the ATF temperature according to the following table. (Insert table here) 14) Remove the overflow plug and adjust oil quantity. If the ATF overflows, go to step 17, and if the ATF does not overflow, go to step 15. 15) Remove the refill plug. 16) Fill ATF to the refill plug until it flows out from the overflow plug. 17) When the ATF flow slows to a trickle, install the overflow plug. 18) Install the refill plug (only if the refill plug has been removed). 19) Lower the vehicle down. 20) Turn the ignition switch OFF to stop the engine. For details about the ATF Filling procedures, see the 2004 4Runner Repair Manual (Pub. No. RM1059U)

2008 TOYOTA RAV 4 HANDS FREE BLU LOGIC Installation Manual

download
a. Apply parking brake. b. Protect fender before starting. c. Remove the negative (-) battery termi- nal. CAUTION: Do not touch the positive terminal with any tool during removal. d. Using the protective blanket, cover front seat, side of the shift lever and center console. e. Place removed vehicle components on a protective blanket. Fig. 1-1 2. Vehicle Disassembly a. Remove the radio assembly. 1. Apply protective tape to the area below the left and right trim panel (Fig. 1-2). Panel Removal Tool Fig. 1-2 Socket (10 mm), Ratchet Panel Removal Tool Fig. 1-3 2. Using a panel removal tool, remove the right and left trim panels (Fig. 1-3). NOTE: Start from the bottom and work your way up. 3. Remove the four (4) bolts securing the radio with a 10mm socket/ratchet (Fig. 1-4). 4. Gently pull out the radio and disconnect any connectors (Fig. 1-5). 5. Support the radio on a support box (or with other appropriate means) to prevent any damage to the connections as well as preventing scratches. NOTE: Be careful not to put too much tension on the radio connections when pulling out the radio 2. Wrap the microphone wire with 33cm of 1/4″ wire split loom leaving a minimum of 8mm of wire exposed (Fig. 1-7). 3. Secure wire loom with tape. NOTE: This will help eliminate any possibility of the factory plastic trim puncturing the wire. 4. Clean the microphone location with an approved VDC cleaner. 5. Now pull back on the trim to disengage, allowing enough gap for the microphone wire (Fig. 1-7). 4. Interface Module Installation a. Connect the main power harness to the matching interface module connections (Fig. 1-9). b. Also connect the microphone wire to the module. NOTE: The Red connector is connected to the matching Red connector on the module. DO NOT remove protective foam wrap from the module. 6. Mount the rear of the microphone vertically to minimize the amount of exposed wire visible to the customer. 3-10mm of exposed wire is acceptable (Fig. 1-8). 7. Route microphone wire through the small hole marked by the yellow arrow in Figure 1-8. 8. Re-engage panel and reinstall Phillips screw. Fig. 1-8 Fig. 1-9 Fig. 1-7 Trim ? ? ? ?