diagram wire harness drivers door honda

You search PDF repair manual about diagram wire harness drivers door honda, if there are search results will appear below. If search results do not exist, please search by others keyword.



  diagram wire harness drivers door honda Direct Download speed 5432 Kb/s

  diagram wire harness drivers door honda Full Version speed 8172 Kb/s



2000-2006 TOYOTA TUNDRA VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 22-05-2011

download
WIRING INFORMATION: 2000 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 2001 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Doo

Related Content:

Blue Point Eecr2 Manual, blue piont EECR2 manual, 2006 Tundra trailer wiring, google com/wire harness repair 2007 impala, 2003 chevy silverado instrument cluster ground wire, toyota pbt-gf15, trailer hitch pbt gf15, how to remove kick panel 98 cavalier, how to verify a wiring harness pin out, is there a wiring harness connector in the door sill of a 2005 dodge ram?

2000-2004 TOYOTA ECHO VEHICLE WIRING INFORMATION

0

Filed Under (Toyota Manuals) by admin on 21-05-2011

download
WIRING INFORMATION 2002 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION 2003 Toyota Echo WIRE WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE/RED and WHITE/BLUE Ignition Harness 12V IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness When installing a remote start, the second ignition wire (BLACK/RED) must be isolated from the key switch ACCESSORY WIRE WHITE/BLUE Ignition Harness STARTER WIRE BLACK Ignition Harness PARKING LIGHTS (+) GREEN At Headlight Switch POWER DOOR LOCK (-) BROWN/YELLOW Harness In Passenger’s Kick Panel POWER DOOR UNLOCK (-) GREEN/BLACK Harness In Passenger’s Kick Panel DOOR TRIGGER (-) RED/WHITE At Top Of Fuse Box TRUNK TRIGGER (-) RED/BLUE Harness In Driver’s Kick Panel FACTORY ALARM ARM Arms with lock FACTORY ALARM DISARM Disarms with unlock TACHOMETER BLACK At Diagnostic Plug Under Driver’s Side Of Dash BRAKE WIRE (+) GREEN/WHITE At Brake Pedal Switch HORN TRIGGER (-) WHITE/RED Harness At Steering Column LEFT FRONT WINDOW UP RED At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN GREEN At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/YELLOW Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN GREEN/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN GREEN/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

2004 chevy traiblazer drivers side front axle seal, 08 silverado driver door wire harnes, wanted driverside wire harnes for 2008 pontiac torrent, Differential Seal for 2004 Trailblazer, the cable under the front light of the car is detached, no black smoke from 3406b, post ignition power source 2008 gmc sierra, recoding chevrolet silverado ignition, replacement resistor for dodge ac, saab window control module

1991-1994 FORD TEMPO VEHICLE WIRING

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

1999 CHEVY SILVERADO DRIVER MIRROR MOTOR installation Instructions, 2003 pontiac vibe installing a 2 wire push button, 2002 lincoln town car driver side door expanted view, 2008 chevy driver door switch wiring schmatic, 1999 cadillac deville drivers seat diagram, 04 impala driver side window regulator diagram, driver\s junctio nbox 2 accord 2012, drivers side front door on a 2002 mercury marquis wont close, honda cr-v drivers side armrest, drivers side window repair 2001 Dodge Dakota

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2012

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.

Related Content:

remove and replace 2000 echo door handle, removing door lock on lexus IS300, 2010 silverado door lock actuator diagram, how to replace heater blend door actuator 2003 Monte Carlo, blend door on 2005 dodge durango, 52409974 diagram, Repair door lock on 1999 tocoma, how to open the fuel door on a 2007 chevy suburban, blend door screws, how to open gas on 2007 suburban

2010 TOYOTA PRIUS FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
Items required for installation: Push pin 10mm bolt 10mm nut TOYOTA PRIUS 2010 FOG LAMP KIT 1 of 4 01-25-2010 STEP 3.2 • Attach fog lamp to bezel. STEP 3.3 • Fog lamp and bezel assembly. STEP 3.4 • Place fog lamp and bezel assembly onto vehicle. Fasten fog lamp to vehicle with 10mm nut and supplied screw. ( Repeat step 3 for passenger side ) STEP 4.0 Removal of interior trim on driver side STEP 4.1 • Pull up on lower door trim. STEP 4.2 • Foot panel-Remove 16mm plastic nut. STEP 4.3 • Pull foot panel inward toward center console. STEP 4.4 • Remove screw. STEP 4.5 • Disconnect hood release cable from latch by pulling down on the black cable freeing it from its location. Then moving the cable to the left away from the mounting bracket. STEP 4.6 • Remove cable from latch. STEP 4.7 • Pull lower left interior panel away from dash and unplug connectors. CAUTION! You may damage wiring and connectors if you pull too hard. Driver side interior removed. 2 of 4 01-25-2010 STEP 4.8 • Remove two screws and push back on tab to free lower panel. STEP 4.9 • Unplug connector and wire harness from panel and remove panel by pulling it toward the driver seat. STEP 5.0 Fog lamp switching wiring • Run WHITE wire through V-channel and pull female bullet connector end towards fire wall. • Connect ground wire to dashboard frame. STEP 5.4 • Plug green connector into fog lamp switch. (Plug all connectors removed from Step 4 and place panel back in position) STEP 6.0 Fog lamp wiring harness • From the panel removed under the steering wheel locate hole in grommet. STEP 6.1 • Puncture hole with O-ring pick/Philips screw driver or any sharp object no larger that the black tubing. (You want a tight seal between grommet and wire). STEP 5.1 • Remove tape from lower connector on ECU and locate BROWN wire. Use the bridge connector to connect RED wire to BROWN wire. You may need to cut RED wire to proper length. STEP 5.2 • Remove. STEP 5.3 • Replace with fog lamp switch. STEP 6.2 • Insert coat hanger or welding rod through punctured hole. Push rod far enough into engine compartment so you can retrieve it. STEP 6.3 • Bend tip or rod with needle nose pliers. STEP 6.4 • Insert hook end into bullet connector making sure black tubing is close to rod. V-channel Ground 3 of 4 01-25-2010 STEP 6.5 IMPORTANT! Wrap electrical tape around connector, tubing and rod. It is important that all three be secured as one unit so not to rip connector from wiring. You want tubing to take as much of the pull force as possible. STEP 6.6 • Apply soapy water to the entire length of black tubing and from the inside of the vehicle pull rod until wire breaks through grommet. 2.5-3ft of wiring should be sufficient. STEP 6.7 • Run wiring along side the black tube indicated until it meets female end of the WHITE fog lamp wire switch. STEP 6.8 • Connect both ends together and tie strap wiring to black tube. STEP 6.9 • On the top left corner of the fuse box (to the right of the brake fluid reservoir) locate silver ECU mounting bracket. STEP 6.10 • Remove 10mm bolts and attach BLACK ground and relay as indicated. STEP 6.11 • Attach harness connector to relay. STEP 6.12 • Run wire harness between ECU and fuse box. Run RED power wire along the same path as WHITE power wire in fuse box. Connect RED power wire to 12V power source directly above WHITE cable. STEP 7.0 Connecting wire harness to fog lamps • Run wiring for driver and passenger side lamps down toward driver side fog lamp. • Connect shortest harness to driver side fog lamp. Run wire harness alongside turn signal harness. • Use the supplied tie straps to secure passenger side wire harness along the radiator support frame shown. • Connect harness to fog lamp • END of installation

Related Content:

2010 prius fuse locations, Toyota Prius 2010 service manual, removing starter from 2005 crv, REMOVE AND REPLACE 2005 HONDA CRV STARTER, prius 2010 fuel pump fuse, kia rip radiator hose, ignition wire set 8MM Kia Sportage 2010 LX, how to change thermostat c arcadia, How do I remove the starter on a Chevy Cobalt 2006, Honda malfunction reset button location

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

2005 TOYOTA SCION XB LSD INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 14-02-2011

download
INSTALLATION INTRODUCTION 1. REMOVING THE FENDER AND DOORS FROM THE A-PILLAR AND DISCONNECTING THE WIRE HARNESS @ THE DOOR JAM 2. REMOVING THE EXISTING DOOR HINGES FROM THE DOORS; TOP AND BOTTOM. 3. MODIFYING THE INTERNAL FENDER AREAS FOR THE HINGE CLEARANCE. 4. MODIFYING THE ELECTRICAL HARNESS. 5. HANGING AND ALIGNING THE VEHICLE DOORS. 6. INSTALLING THE FENDER AND CHECKING FOR CLEARANCE. 7. REMOVE FENDER AND ROUTING THE WIRING. 8. RE-INSTALL FENDER AND CHECK FOR CLEARANCE. 9. JOB COMPLETE! REMOVING THE O.E.M. DOOR AND O.E.M. HINGES 1a. Open the door and locate the door hinges ( Photo 1 ). 1b. Un-bolt the four bolts that mount the O.E.M. hinges (with the doors attached) and remove them completely off the A-Pillar. 1c. Remove the four bolts mounting the hinges to the door frame, removing the hinges DIS-ASSEMBLING THE SWING ARM FROM THE GROUND PLATE 2a. Your new LSD Door Hinges have come assembled. 2b. As identified in ( Photo 2 ), disassemble the swing arm from the ground plate. Un-bolt all four mounting bolts or allen-heads and remove completely, detaching the swing arm from the ground plate. 2c. Place the four mounting bolts in an area where they will not be lost MODIFYING THE CHASSIS WIRING HARNESS IMPORTANT NOTE: Prior to beginning extending the wiring harness from the A-pillar, each individual wire needs to be cut one at a time. Each wire that is cut, has to be staggered (See 4g) from the previous cut wire. By doing this, you will eliminate, when wrapping all the wires, one large taped ball. 3a. If the wiring harness comes equipped with an insulation cover, this will need to be r emoved. STEPS 3b thru 3f are for REFERENCE ONLY (using the white wire as reference) 3b. Isolate a single wire ( Photo 3 ). Start the first cut on the white wire approximately 3″ from the door frame. 3c. Cut the wire sheath (coming from door frame) back approximately 1/4″ ( Photo 4 ). Twist the end tight. 3d. Cut the wire sheath (from kit supplied white wire) back approximately 1/4″. Twist the end tight. 3e. Using the kit supplied heat shrink connector ends, insert the wire ends into the connector, one from each end ( Photo 5 ). 3f. Using the heat gun, shrink wrap the connector ends to securely mate with the wire

Related Content:

2005 scion xb repair manual download

2007 Toyota Camry equipped with the Smart Key System with Push Button Start Remote Starter Integration

0

Filed Under (Toyota Manuals) by admin on 20-05-2011

download
Material required: – Remote Car Starter – Xpresskit : XK05-PKT2 or Bypasskit :PKT2 – One 5-wire relay for auto lamp circuit Key required for programming: 1 Average installation time: 2.5 hours Difficulty level: Medium 2.0 Preparation: -Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes. -Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily. 3.0 Installation: The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system. 3.01 Main Ignition Harness Connection: Most of the connections will be done behind the Fuse box. This fuse box is located under the driver side underdash. Also, the vehicle’s TACH wire can be found inside vehicle, as per diagram below and it is suggested to use this wire for the remote start tach source. The remote start hood pin switch wire is the only wire which must be run into the engine compartment for safety. Accessory (+): White Ignition 1 (+): Pink Ignition 2 (+): Light Green Starter (+): Grey Tach: Black 3.02 Wiring location for the Bypasskit XK-05 PKT2: The connection for the XK05-PKT2 will be done on the driver side under dash. The wires required are from a 5 wires harness coming from behind the heater module, high above the gas pedal near the firewall. The five wires in this harness are as follows: Blue: transponder IMI (Immobilizer in) wire, which gets cut in two and wired in series. The bottom-half wire connects to the kits Violet/White wire and the top-half wire connects the kits Violet wire. Green: transponder IMO (Immobilizer out) wire, which gets wired in parallel with the kits Orange wire. White/Black, White & Orange… these wire are not used for installation The GREEN LED output wire from the XK05-PKT2 is not required for this installation. The vehicle LED does come on during remote start. 3.03 Wiring location for door locks and factory alarm control: The wires to control the factory alarm and the door locks are located behind the driver’s kick panel. These wires must receive negative pulses. It is mandatory to disarm the OEM alarm system before remote start sequence Grey Unlock Wire : A double pulse unlock (-) output is required to disarm and unlock all doors. The first unlock (-) pulse disarms OEM alarm and unlocks driver’s door, the second pulse will unlock all other doors. In order to disarm the OEM alarm when remote starting, this GREY wire requires a pulse before start, which unlocks the driver’s door. So, if the remote systems unlock output does offer a pulse before start, then connect both the unlock and disarm (-) output wires to the vehicle’s GREY unlock wire. Brown Lock Wire : In order to lock and arm the OEM alarm system a (-) pulse is required for the vehicle’s BROWN lock wire. If the vehicle’s ignition on the alarm will not arm, if locking with remote.

Related Content:

2007 camry speed sensor wire burn under dash, 2007 dts electrical problem no start or cranking alarm not working, 2007 impala starter problems, 2007 toyota camry key broke, how to install XT-016C fog lights 2011 camry, smart kye push waring diagram 2007, were is the modile located on remote starts

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 14-06-2012

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

Related Content:

how to change door latch for Saab 9-3, how to replace inside door latch cable gmc trucks, how to replace door latch on 1999 chevy silverado, 2014 FUSION REAR INNER HANDLE, 05 pontiac g6 door latch, Ford Fusion Door Diagram, honda crv 2002 door cylinder fix, how to fix my door push button on driver door 2007 grand prix gxp, how to install door handle clips, how to remove the rear door outer handle on a 2014 Ford Fusion

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

Related Content:

Blue Point Eecr2 Manual, blue piont EECR2 manual, 2006 Tundra trailer wiring, google com/wire harness repair 2007 impala, 2003 chevy silverado instrument cluster ground wire, toyota pbt-gf15, trailer hitch pbt gf15, how to remove kick panel 98 cavalier, how to verify a wiring harness pin out, is there a wiring harness connector in the door sill of a 2005 dodge ram?