diagram of a 1998 ford escort zx2 transmission

You search PDF repair manual about diagram of a 1998 ford escort zx2 transmission, if there are search results will appear below. If search results do not exist, please search by others keyword.



  diagram of a 1998 ford escort zx2 transmission Direct Download speed 5432 Kb/s

  diagram of a 1998 ford escort zx2 transmission Full Version speed 8172 Kb/s



4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2011 crv engine whine, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, automatic transmission adjustments for 1997 yuko, 2004 saturn Clutch Assembly Exploded View, transmission module for 1999 ford ranger xlt, 4r70w transmission rebuild manual download

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

0

Filed Under (Chevy Manuals) by admin on 18-05-2011

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

Related Content:

wiring for case w20 loader, case 444-75 repair manuals free, How to rebuild Kia Sorento Transfer Case, Case 1845C Manual Download, np 208 service manual, toyota tacoma ground wire transfer case, Chevy NP208 Rebuild Instructions, 2001 ford sports trac 4x4 transfer case wiring diagram, f150 transfer case problems, ford 2003 ford explorer how transfer case works

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, what is the tcc solenoid on a 2 2 cavalier, bully side ste for jeep instructions, Powertrain Generator 6500 Parts Diagram, 2006 pontiac g6 gt code po753, powertrain generator 6500 owners manual, powertrain generator parts, p1860 tcc pwm solenoid circuit electrical, no powertrain dtc\s or freeze frame data, powertrain generator ptg1000

1998 Ford Escort ZX2 L4-2.0L DOHC Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 06-05-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1). 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) 10. Remove original front and rear engine support cross-member bushings (Figure 3). Zoom Sized for Print a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.)

Related Content:

2004 chevy colorado 3 5 camshaft actuator, 2002 ford escort manual pdf

1990 Toyota Supra Factory Repair Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.

1998 Ford Escort Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 30-04-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1) 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.).

2002 Isuzu Truck Axiom Vehicle Level Transmission and Drivetrain Automatic Transmission/ Transaxle Fluid – A/ T Service and Repair

0

Filed Under (Isuzu Manuals) by admin on 09-01-2012

download
Changing Transmission Fluid There is no need to change the transmission fluid unless the transmission is used under one or more of the following heavy duty conditions. A. Repeated short trips B. Driving on rough roads C. Driving on dusty roads D. Towing a trailer If the vehicle is used under these conditions, change the fluid every 20,000 miles (32,000 km). 1. Place a large drain pan under the oil pan. 2. Remove the transmission oil drain screw (2) and drain fluid. 3. Tighten drain screw (2). Torque: 38 Nm (28 ft. lbs.) 4. Remove the transmission overfill screw (1) and fill transmission through overfill screw opening, using DEXRON-III ATF. Note: Add transmission fluid until it flows out over the overfill screw opening. 5. Let engine idle until a fluid temperature between 32°C (90°F) and 57°C (135°F) is reached. 6. Add transmission fluid until it flows out over the overfill screw opening, then close the overfill screw (1). Torque: 38 Nm (28 ft. lbs.) Note: To prevent fluid leaks, the overfill screw and oil drain screws gasket must be replaced each time these screws are removed. Note: Check transmission fluid temperature with scan tool

Related Content:

1999 ISUZU RODEO HOW TO REPLACE TORQUE CONVERTER

1999 Mercury Sable V6-3.0L DOHC A/ T-Cooler Flushing Service Manual

0

Filed Under (Mercury Manuals) by admin on 25-06-2012

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers. ^They do not provide the volume necessary to remove heavy contaminants. ^They evaporate quickly and essentially leave contaminants in pockets, bends, or wherever they are as the solvent dries. ^TORQSHIFT, 4R100, E40D, C6 – The REAR transmission case filling receives the return line. ^4R70W, AODE, AOD – The TOP transmission case filling receives the return line. ^A4LD, 4R44/55E, 5R55E, 5R55N, 5R55W, 5R55S The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes

Related Content:

4f27e overhaul manual/pdf, ax4n transmission repair manual pdf, 4f27e case torque specs, 5r55eiol pump spec, 5r55s overfill symptoms, 5r55w transmission manual download, cd4e transmission pump removal, Idetnify Ax4N automatic transmission

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

2002 Dodge Truck RAM 2500 Symptom Related Diagnostic Procedures/ Installation Manual

0

Filed Under (Dodge Manuals) by admin on 16-02-2012

download
46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges. The Clutch and Band Application chart provides a basis for analyzing road test results. Note that the rear clutch is applied in all forward ranges (D, 2, 1). The transmission overrunning clutch is applied in first gear (D, 2 and 1 ranges) only. The rear band is applied in 1 and R range only. Note that the overdrive clutch is applied only in fourth gear and the overdrive direct clutch and overrunning clutch are applied in all ranges except fourth gear. For example: If slippage occurs in first gear in D and 2 range but not in 1 range, the transmission overrunning clutch is faulty. Similarly, if slippage occurs in any two forward gears, the rear clutch is slipping. Applying the same method of analysis, note that the front and rear clutches are applied simultaneously only in D range third and fourth gear . If the transmission slips in third gear, either the front clutch or the rear clutch is slipping. If the transmission slips in fourth gear but not in third gear, the overdrive clutch is slipping. By selecting another gear, which does not use these clutches, the slipping unit can be determined. For example, if the transmission also slips in Reverse, the front clutch is slipping. If the transmission does not slip in Reverse, the rear clutch is slipping. If slippage occurs during the 3-4 shift or only in fourth gear , the overdrive clutch is slipping. Similarly, if the direct clutch were to fail, the transmission would lose both reverse gear and overrun braking in 2 position (manual second gear). If the transmission will not shift to fourth gear , the control switch, overdrive solenoid or related wiring may also be the problem cause.

Related Content:

replacing a torque converter clutch solenoid on a kia, torque converter cluch selenoid on 1999 odyssey, cd4e application chart, 47 no forward gears, ax4n clutch and band chart, ford cd4e automatic gear chart, ford cd4e gear chart, How to fix f150 torque converter clutch solenoid, Overdrive Solenoid Symptoms, ranger ac clutch solenoid 2001

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2011 crv engine whine, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, automatic transmission adjustments for 1997 yuko, 2004 saturn Clutch Assembly Exploded View, transmission module for 1999 ford ranger xlt, 4r70w transmission rebuild manual download