Skip to content

diagram of freelander rear brakes

You search PDF repair manual about diagram of freelander rear brakes, if there are search results will appear below. If search results do not exist, please search by others keyword.

Steering, Brake And Suspension Specialists Proportioning Valve Diagram

download
This diagram is the most common way to plumb a proportioning valve. In some cases, the right front line will be plugged off at the proportioning valve and the left front line will go to a “T” fitting. From the “T” fitting, the front lines then split off and go to the left and right wheels. Our proportioning valve has a warning light switch built in (this is not a stop light switch.) The warning light will detect any loss of pressure, for example, a leaky wheel cylinder. We recommend you wire this light into your system. Any two wire light socket will work. One wire goes to the accessory power and the other goes to the warning light. Our proportioning valves provide four functions: 1. Proportion pressure front and rear 2. 10 psi. residual check valve 3. Metering valve to apply pressure to the rear brakes before the front brakes 4. A brake warning light to detect a loss in pressure Proportioning Valve Plumbing Diagram: There are two proportioning valve lines that connect to the master cylinder provided in our kits. The first is a 90 degree bend with one leg longer than the other. This line must be oriented with the long leg connected into the front top hole of the proportioning valve and the short end in the front hole on the master cylinder. The second line has two 90 degree bends and has color coded fittings. The larger blue fitting goes into the back hole on the master cylinder and the smaller gold fitting goes into the back top hole on the proportion valve as shown in the diagram

HONDA CR-V Moan or Groan From the Rear Differential REPAIR PROCEDURE

download
REPAIR PROCEDURE: 2002-04 MODELS 1. Replace the rear differential fluid: •Refer to page 15-13 of the 2002-04 CR-V Service Manual , or •Online, enter keywords REAR DIFF, and select Rear Differential Fluid Inspection and Replacement (4WD) from the list. 2. Raise the vehicle on a lift until all four wheels are completely off the ground and can rotate freely. 3. Start the engine, and let it idle until the radiator fan cycles on and off twice. 4. Burnish the rear differential clutches: Automatic transmission models – •Set the parking brake, and shift the transmission to D. Let the engine idle for 5 minutes. •With the shift lever in D, release the parking brake, keep the wheel speed at 10 mph, and let all four wheels rotate freely for 5 minutes. •Apply the brakes to stop the wheels, repeat the bulleted steps one more time, then go to step 5. Manual transmission models – •With the engine idling and the parking brake released, shift the transmission into 1st, release the clutch, and let the wheels rotate for 5 minutes. •Disengage the clutch, and apply the brakes to stop the wheels. Shift the transmission into reverse, release the clutch, and let the wheels rotate for 5 minutes. •Shift the transmission into neutral, then apply the brakes to stop the wheels. •Repeat the bulleted steps one more time, then go to step 5. 5. Shift the transmission to P (A/T) or neutral (M/T), and turn off the engine. 6. Let the rear differential cool for 10 minutes

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

2002 Ford Truck Ranger Brakes – Rear Brakes Grabbing Condition Repair Manual

download
SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate . WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable . 4. Inspect and clean the lining contact area of the brake drum ; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. Zoom Sized for Print 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^Hold Down Pins 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.