Skip to content

diagram of subaru transmission 92

You search PDF repair manual about diagram of subaru transmission 92, if there are search results will appear below. If search results do not exist, please search by others keyword.

1991 Subaru Legacy Sedan 4WD Manual Transmission/ Transaxle: Service and Repair Removal

download
1. Open front hood and support with a stay. 2. Disconnect battery cables from battery. 3. Remove air intake duct. 4. Remove clutch cable, return spring and hill-holder cable. 5. Disconnect the following: -Oxygen Sensor connector -Crank Angle Sensor connector -Cam Angle Sensor connector -Knock Sensor connector -Transmission Harness connectors -Transmission Ground Terminal 6. Disconnect start connector and terminal and remove the starter assembly. 7. Remove pitching stopper rod. 8. Remove connector holder bracket 9. Set the engine support assembly (927670000). 10. Remove engine to transmission mounting nut and bolt on the upper side. 11. Raise and support car then disconnect the front exhaust pipe from the engine. Note: Remove all nuts except one. This nut is used to temporarily hold the exhaust pipe. 12. Disconnect the front to rear exhaust pipe connection. 13. Disconnect front exhaust pipe at transmission and hanger locations. 14. Remove the nut which was used to temporarily hold the exhaust pipe in step 11 and disconnect the front exhaust pipe. 15. Disconnect rear exhaust pipe from muffler. 16. Remove front cover of rear differential mount. 17. Remove the four bolts which hold the propeller shaft to rear differential. 18. Remove the two bolts which hold the center bearing to the car body.

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

1991 Subaru Loyale Sedan (4 Door) Camshaft And Timing Belt Repair Manual

download
Tightening torque: REMOVAL 1. Loosen water pump pulley mounting nuts or bolts. 2. Loosen two alternator mounting bolts, and detach V-belt. [Except air conditioner equipped model] 3. Remove water pump pulley and pulley cover. 4. Disconnect lead from oil pressure switch. 5. Remove oil level gauge guide together with gauge. 6. Remove crankshaft pulley. To lock crankshaft, use FLYWHEEL STOPPER [manual transmission model] or DRIVE PLATE STOPPER [automatic transmission model]. 7. Remove belt cover plate. [TURBO model] 8. Remove belt covers LH, RH and FR. 9. Removing timing belt Zoom Sized for Print (a) Loosen tensioner mounting bolts on # 1 cylinder by 1/2 turn. (b) With tensioner fully turned to slacken belt, tighten mounting bolts. (c) Mark rotating direction of timing belt, then remove belt. (d) Loosen tensioner No. 2 mounting bolts on # 2 cylinder by 1/2 turn. (e) With tensioner fully rotated to slacken belt by using TENSIONER WRENCH, tighten tensioner mounting bolts. NOTE: Cover TENSIONER WRENCH clamping tips with a rubber hose or waste cloth to prevent crankshaft or pulley from being damaged 10. Remove tensioner and tensioner No. 2 together with tensioner spring. 11. Remove belt idler. 12. Remove camshaft sprockets by using CAMSHAFT SPROCKET WRENCH. 13. Remove right-hand belt cover No. 2, left-hand belt cover No. 2 and belt cover RR. TIMING BELT 1. Check timing belt teeth for breaks, cracks, and wear. If any fault is found, replace belt. 2. Check the condition of back side of belt; if any crack is found, replace belt. A. Be careful not to let oil, grease or coolant contact the belt. Remove quickly and thoroughly if this happens. Zoom Sized for Print

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.