dodge ram wiper motor wiring diagram

You search PDF repair manual about dodge ram wiper motor wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  dodge ram wiper motor wiring diagram Direct Download speed 5432 Kb/s

  dodge ram wiper motor wiring diagram Full Version speed 8172 Kb/s



Windshield Wiper Linkage Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
Installation Instructions 1. Place the Wiper Motor Mount Plate (FFR# 25391) along the edge of the ¾” shock tower support tube on the passenger side and the top of the footbox front wall aluminum. Mark the location for the riv nuts (4 total). 2. Drill the riv nut holes using a 25/64″ drill bit. You may want to begin by using a smaller drill bit to drill a pilot hole first (shown). 3 3. Intsall the 1/4″ riv nuts (4) using the supplied riv nut tool. 4. Install one of the rod ends (FFR# 25724) with the supplied jam nut (FFR# 25725) onto the wiper motor arm (1/2″, 9/16″ wrenches). You will have to trim some of the excess thread off of the rod end in order for it to have sufficient clearance between it and the wiper motor mount plate. 4 5. Place the wiper motor in the mount plate (FFR# 25391) so the pins on the motor fit inside the holes in the mount plate and the three threaded holes in the motor line up with the corresponding holes in the mount plate. 6. Using the three Corvette screws that held the motor in place, fasten the motor to the mount plate (T- 30 Torx). 7. Place a nylon spacer (FFR# 10960) between the frame and the mount plate at each of the riv nuts and bolt the plate into positon using the supplied ¼”-20 x 1.5″ long bolts (4mm allen).
6 ATTENTION: For the bolt at the front corner of the plate, you may have to use the supplied washers as well as the nylon spacer to prevent the bolt from bottoming out before the plate is firmly in place (See photo). 8. Screw the supplied section of threaded rod (FFR# 25723) into the rod end on the wiper motor. 7 9. Slide the aluminum tube (FFR# 25934) over the threaded rod and measure how much of the aluminum tube will need to be trimmed once the rod end is screwed on. Trim the tubing with a tubing cutter/hacksaw/cutoff wheel. 10. As you did with the rod end on the wiper motor, you will have to trim the threads on the rod end to clear the aluminum. 11. Place the aluminum tube over the threaded rod, then screw the rod end (FFR# 25724) onto the rod until tight. 12. Before installing the wheel box to the body you will have to trial fit the wiper arm to the wheel box. It is a tight fit, so you may have to spray the splines with some WD-40 or some oil and tap the wiper arm onto the splines. Remove the wiper arm from the wheelbox so you can bolt it to the body. 8 13. Follow the instructions in the assembly manual for bolting the wheelbox to the body. 14. Install the rod end on the wiper wheel box arm with the supplied jam nut (FFR# 25725) (1/2″, 9/16″ wrenches). 15. Install the wiper blade (FFR# 25629) onto the wiper arm (FFR# 25552). 16. Clip the wiper arm onto the shaft of the wiper wheel box, making sure that the tab on the arm clips into the channel on the wheel box shaft (clip shown). 9 17. Spray the windshield with water, or glass cleaner. Check the sweep by turning the wipers on – start with the slowest setting to avoid damaging the linkage or running the wiper beyond the windshield. Make any necessary adjustments, and the linkage installation is complete

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, 2008 colbalt heater core removal, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, heater core return hose 03 monte carlo, 2003 durango sxt hvac blower motor resistor wiring diagram, cruise control cable repair end

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra, silverado motor mount replace

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 2003 s10 airbag wiring diagram, abs and Anti Theft Passive 2000 mercury cougar, 1998 Dodge Dakota Service Manual, dodge durango 2002 suspension layout, zimmatic pivot wiring, troubleshooting front blower motor resistor in a 2005 dodge durango, 97 buick riviera Ignition Switch Diagram

1992 Cadillac Deville 4.9L Windshield Wiper Blade and Arm REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Cadillac Manuals) by admin on 22-05-2011

download
REMOVAL & INSTALLATION Catera Open the hood. 1. Remove the windshield wiper arm stud cap that conceals the nut. 2. Remove the windshield wiper arm nut. 3. Grasp the windshield wiper arm with both hands. 4. Use a rocking motion to loosen the windshield wiper arm from the pivots. 5. Remove the windshield wiper arm and blade. 6. To install: Installation is the reversal of the removal procedure. 7. Deville and Fleetwood WIPER ARM Raise the hood as needed for access to the wiper arms. 1. Operate the wipers and turn the ignition OFF when the wipers are at the mid-wipe position. 2. Lift the wiper arm from the windshield. 3. On 1990 vehicles, pull the retaining latch and remove the arm from the transmission shaft. 4. On 1991-93 vehicles, disengage the retaining latch using a suitable tool and remove the arm from the transmission shaft. 5. To install: Install the wiper arm onto the transmission shaft. 6. Push the retaining latch in and return the arm assembly to the windshield. 7. Park the wipers. If adjustment is necessary, proceed as follows: Remove the right wiper arm. a. Open the small door to access the wiper linkage; refer to the illustration for details. b.

Related Content:

1992 cadillac seville manual free download, how to remove wiper arm assembly chevy impala recalls, 1992 Cadillac Deville Owners Manual, 2007 chevy tahoe rear windshield wiper arm remove, cad 1992 seville horn low volume ?, how to replace a windshield wiper motor on a 2004 impala, remove wiper arm 04 ompala, video of how to install a windshield wiper arm on a rv

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 27-02-2011

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

Related Content:

replace 2002 suburban fan motor, 2004 cavalier stepper motors, hino blower motor replace procedure, installing heaterfan motor dodge grand caravan 2011, instructions for replacing 2004 pontiac grand prix blower motor, is the resisistor built in the blower motor on a 2012 chevy sonic?, remove heat blower motor 67 grand prix, to replace an a/c motor on a 2003 civic, wireing for blower control 2004 silverado, Hino 268 2013 fuse box for heater

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix

1999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation Manual

0

Filed Under (Ford Manuals) by admin on 05-07-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the driver side air bag module. For additional information, refer to Section 501-20B . 2. Remove the passenger side air bag module. For additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connector. 7. Disconnect the windshield wiper motor electrical connector. * Release the wiring harness locators. 8. Disconnect the LH engine compartment in-line electrical connectors. 9. Unseat the LH wiring harness grommet 10. Disconnect the blower motor electrical connector. 11. Disconnect the A/C pressure cut-off switch electrical connector. 12. Disconnect the RH engine compartment in-line wiring harness connectors. 13. Disconnect the vacuum line at the intake manifold. 14. Disconnect the electronic air temperature control (EATC) variable blower motor controller electrical connector. * Release the wiring harness locators. 15. Remove the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 16. Remove the upper front fender splash shield bolts. 17. Remove the lower front fender splash shield bolt and locator. 18. Position the front fender splash shield away from the dash panel. 19. Unlock the wiring harness guide. 20. Unseat the RH wiring harness grommet. 21. Install the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 22. Remove the RH instrument panel lower insulator. 1. Remove the pin-type retainers. 2. Release the locking tab. 3. Remove the instrument panel lower insulator. * Disconnect the courtesy lamp.

2005 Chevy Truck Silverado 1500 2WD Blower Motor Resistor Replacement

0

Filed Under (Chevy Manuals) by admin on 29-04-2012

download
Blower Motor Resistor Replacement Notes BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.

Related Content:

2005 chevy blower motor resistor ground connections, testing mazda 5 for faulty blower moror, resistor sl1, part number 05 silverado blower resistor fix, fan blower resistor for 1998 buick regal, how to change blower motor 2005 hummer h2, how to rotate resistor in schematics, NISSAN CHANGED BLOWER RESISTOR MAKING NOISE WHEN CRANK, removal/replacement of stepper motor in a 05 tahoe, removing blower motor from 2002 tundra

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, PIN DATA 2005 скачать, what pins are positve and negative on a 40 pin cat ecm

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage