Skip to content

ecm codes 2001 ford expedition

You search PDF repair manual about ecm codes 2001 ford expedition, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997-2001 FORD EXPEDITION ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE

download
SUSPENSION, AIR SUSPENSION DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 RIDE HEIGHT RESET PROCEDURE ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE SERVICE PROCEDURE AIR SUSPENSION DTC’S THAT ARE PRESENT NOTE BEFORE ADDRESSING B2140/C2140. DURING PDI (PRE-DELIVERY INSPECTION) IF WARNING “CK SUSP” LIGHT IS ON, PRIOR TO SENDING WARNING: BEFORE REPLACING ANY AIR TO SERVICE, VERIFY SWITCH IN UPPER RIGHT SUSPENSION COMPONENTS, HOISTING, KICK PANEL IS ON. THIS SWITCH IS TURNED JACKING, OR TOWING, DISCONNECT POWER OFF DURING VEHICLE SHIPMENT TO PREVENT TO THE SYSTEM BY TURNING OFF THE AIR MODULE FROM SEEKING TRIM HEIGHT WHILE SUSPENSION SWITCH LOCATED IN THE RIGHT SECURED DOWN FOR TRANSPORT. KICK PANEL AREA TO PREVENT VEHICLE NOTE DAMAGE OR PERSONAL INJURY. AN INADVERTENT B2140 OR C2140 MAY RAS ONLY – CLEAR 2140 RESULT IF A PARAMETER RESET (CLEAR RIDE HEIGHT) IS SELECTED UNDER NGS ACTIVE NOTE COMMANDS, THEN CANCELLED OUT. EVEN RAS (4X2) EQUIPPED VEHICLES REQUIRE STORING RIDE HEIGHT AND NOTE TOGGLING FRONT TO “ON” TO CLEAR A CK THE AIR SUSPENSION CONTROL MODULE SUSP LIGHT/2140 CODE. THIS ALLOWS THE PART NUMBER IS INTERCHANGEABLE MODULE TO STORE THE VOLTAGE WITH NO BETWEEN THE REAR AIR SUSPENSION (RAS) FRONT HEIGHT SENSOR PRESENT, AND MUST AND 4-WHEEL AIR SUSPENSION (4WAS) BE DONE EVEN WITH CONVENTIONAL (STEEL SYSTEMS, BUT ONCE THE MODULE IS COIL) FRONT SUSPENSION. INSTALLED, THE VEHICLE WILL THEN DETERMINE WHETHER VEHICLE IS 4X2 (RAS)

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

2001 Ford Expedition/ Navigator Headliner Removal and Installation Manual

download
Headliner Removal and Installation 1. NOTE: Inspect the shoulder safety belt guide and cover for damage. If the shoulder safety belt guide or cover is damaged or cover does not remain closed, install a new shoulder safety belt guide. NOTE: Shoulder safety belt guide cover shown removed for clarity. From behind the front shoulder safety belt guide cover, release the retaining tab and open the cover. 2. Remove the nut and shoulder safety belt guide. 3. NOTE: Remove the upper attachments first, followed by the front lower attachment and the lower rear hook. Remove the two C-pillar trim panels. 4. Remove the LH and RH A-pillar assist handles. 1. Remove the four screw covers and four screws. 2. Remove the two A-pillar assist handles. 5. NOTE: Release the top attachments by pulling inboard first and then upward to release the lower hook. Remove the two windshield side garnish mouldings. * If equipped, on the LH windshield side garnish moulding, disconnect the cellular phone hands- free microphone electrical connector. 6. Remove the coat hooks. 1. Open the access cover. 2. Insert a screwdriver into the slot and rotate. 3. Remove the coat hooks. 7. Remove the two front door scuff plates (13208). 8. Remove the two rear door scuff plates (13228). 9. Remove the two B-pillar assist handles. 1. Remove the four covers (two on each handle). 2. Remove the four screws (two on each handle). 3. Remove the two B-pillar assist handles 10. NOTE: Remove the upper attachments first and then the lower attachments. Position the two B-pillar trim panels aside. * Remove the two front and two rear door weather seals. 11. Position the two sun visors into the side window position and remove the two inside screws

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

2001 Ford Truck F 150 Engine – Spark Plug Hole Thread Repair Procedure

download
SERVICE PROCEDURE Ford Motor Company now authorizes LOCK-N-STITCH aluminum insert and tool kit as a proper repair procedure. Follow the procedure included in the tool kit for using the tools and inserts. Tool kits and inserts can be ordered from Rotunda by calling 1-800-Rotunda (768- 8632). Choose option two (2), part number 302-00001. NOTE FORD MOTOR COMPANY HAS DETERMINED THAT REPAIRS MADE WITH THESE ALUMINUM INSERTS AND LOCK-N-STITCH TOOLS DO NOT AFFECT THE HEAT TRANSFER FUNCTION BETWEEN THE SPARK PLUG AND THE CYLINDER HEAD. NOTE THIS PROCEDURE IS NOT AUTHORIZED AS A FORD WARRANTY REPAIR. FOR VEHICLES WITHIN WARRANTY, REPLACEMENT OF THE CYLINDER HEAD IS RECOMMENDED. NOTE THIS IS THE ONLY FORD AUTHORIZED PROCEDURE FOR SPARK PLUG THREAD REPAIRS. NOTE THIS PROCEDURE IS AUTHORIZED FOR ESP REPAIRS AND RETAIL REPAIRS. WARRANTY STATUS: Information Only – Not Warrantable