electrical wiring diagram for 1989 chevrolet pickup

You search PDF repair manual about electrical wiring diagram for 1989 chevrolet pickup, if there are search results will appear below. If search results do not exist, please search by others keyword.



  electrical wiring diagram for 1989 chevrolet pickup Direct Download speed 5432 Kb/s

  electrical wiring diagram for 1989 chevrolet pickup Full Version speed 8172 Kb/s



1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, bully side ste for jeep instructions, no powertrain dtc\s or freeze frame data, p1860 tcc pwm solenoid circuit electrical, powertrain generator 6500 owners manual, powertrain generator parts, powertrain generator ptg1000, replace radiator 2000 dodge durango

1999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation Manual

0

Filed Under (Ford Manuals) by admin on 05-07-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the driver side air bag module. For additional information, refer to Section 501-20B . 2. Remove the passenger side air bag module. For additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connector. 7. Disconnect the windshield wiper motor electrical connector. * Release the wiring harness locators. 8. Disconnect the LH engine compartment in-line electrical connectors. 9. Unseat the LH wiring harness grommet 10. Disconnect the blower motor electrical connector. 11. Disconnect the A/C pressure cut-off switch electrical connector. 12. Disconnect the RH engine compartment in-line wiring harness connectors. 13. Disconnect the vacuum line at the intake manifold. 14. Disconnect the electronic air temperature control (EATC) variable blower motor controller electrical connector. * Release the wiring harness locators. 15. Remove the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 16. Remove the upper front fender splash shield bolts. 17. Remove the lower front fender splash shield bolt and locator. 18. Position the front fender splash shield away from the dash panel. 19. Unlock the wiring harness guide. 20. Unseat the RH wiring harness grommet. 21. Install the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 22. Remove the RH instrument panel lower insulator. 1. Remove the pin-type retainers. 2. Release the locking tab. 3. Remove the instrument panel lower insulator. * Disconnect the courtesy lamp.

2000 Ford Crown Victoria/ Grand Marquis Intake Manifold – Gasoline Engines Removal and Installation Manual

0

Filed Under (Ford Manuals) by admin on 16-04-2012

download
Intake Manifold—Gasoline Engines Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 4. Disconnect the fuel line. For additional information, refer to Section 310-00A or Section 310-00B . 5. Remove the wiper arm and pivot shaft. For additional information, refer to Section 501-16 . 6. Remove the drive belt. For additional information, refer to Section 303-05 . 7. Raise the vehicle on a hoist. For additional information, refer to Section 100-02 . 8. Disconnect the electrical connector at the crankshaft position (CKP) sensor. * Disconnect the pin-type retainer from the A/C compressor bracket. 9. Disconnect the electrical connector from the A/C compressor. 10. Remove the oil bypass filter. 11. Disconnect the oil pressure sensor electrical connector and the power steering pressure (PSP) switch electrical connector. 12. Disconnect the exhaust gas recirculation (EGR) tube from the exhaust manifold 13. Lower the vehicle. 14. Disconnect the two differential pressure feedback EGR hoses. 15. Disconnect the RH heated oxygen sensor electrical connector. 16. Disconnect the fuel charging wiring electrical connectors from the eight ignition coils. 17. Disconnect the fuel charging wiring electrical connectors from the eight fuel injectors. 18. Disconnect the accelerator cable and the speed control actuator cable. 19. Remove the cables from the EGR tube heat shield and position out of the way. 20. Remove the bolts and the EGR tube heat shield. 21. Disconnect the evaporative emissions (EVAP) return tube, the main chassis vacuum supply line, and the EGR valve vacuum supply. 22. Disconnect the positive crankcase ventilation (PCV) tube assembly at two locations and remove. 23. Disconnect the electrical connector from the EGR vacuum regulator solenoid. 24. Disconnect the vacuum line from the EVAP canister purge valve. 25. Disconnect the generator cable and electrical connector 26. Remove the bolts and the generator mounting bracket. 27. Remove the upper radiator hose. 28. Disconnect the electrical connector from the idle air control (IAC) valve and the throttle position (TP) sensor. 29. Disconnect the heater water hose. 30. Disconnect the EGR tube from the EGR valve. 31. NOTE: The LH heated oxygen sensor and the transmission electrical connectors are attached to the wiring bracket and must be separated from the bracket. Remove the wiring bracket. * Disconnect the wiring connectors. * Separate the transmission harness from the stud. * Remove the nut and the bolt and remove the bracket.

Related Content:

2005 GMC Sierra 1500 How to Disconnect Vacuum Line, can you unplug the trorque converter on a 1999 honde ex, disconnected battery car turn over will not start 99 bmw 528i, dodge grand caravan liftgate slams shut, part ground strap crown vic 2011 3w7t, where is the vent pipe located on 2004 sierra gas fill up hose

1989-2002 TOYOTA 4-Runner Pickup (standard cab) INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 22-10-2011

download
TOYOTA 4-Runner 1990-95 Pickup (standard cab) 1989-2002 / Pickup (extended cab) 1989-2002 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (3) screws and (1) 10mm bolt from the driver’s side speaker panel and remove the panel. Remove (1) 10mm bolt from the bottom of the passenger’s side speaker panel. Remove (3) screws from the side of the panel and remove the glove box. Remove (4) screws securing the factory head unit and disconnect the wiring. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the climate control knobs. Unclip the climate control trim panel and remove (2) Phillips screws exposed. Unclip the dash trim bezel, lift up on the bezel and remove. DOUBLE DIN APPLICATIONS: Skip to the Installation Instructions for ALL VEHICLES on Page #3. SINGLE DIN APPLICATIONS: Cut and remove the bottom portion of the Radio Housing (see Fig. A) and Faceplate (see Fig. B). Skip to the Installation Instructions for ALL VEHICLES on Page #3. 12 1 2 TOYOTA Tacoma 1995-02 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Pull the cupholder out. Unclip the radio trim bezel and remove. Remove (4) screws securing the factory head unit and disconnect the wiring.

Related Content:

how to remove 2002 toyota tacoma climate control

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

Related Content:

ciol wire problems 2007 camry, priceofcoylepackfora2005kiasedona, chevy 230 cid primary resistor, no power to coil on 1993 dakota, test coil dodge dakota 1993, Isuzu 1997 wiring diagram between coil distibutor, Remove Evap coil from honda element, 1996 dodge dakota 2 5 temperature sensor diagram, replace individual coils on 2002 mercury mountaineer, replacing evaporator on 1999 gmc truck

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals, Uncategorized) by admin on 23-04-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

Related Content:

2000 Isuzu 5 7 NPR Repair Manual lower intake manifold, charging system on 1999 isuzu npr not charging gas engine, ford five hundred instrument panel, remove ac panel from ford five hundred

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, zimmatic pivot wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, 1996 silverado electrical manual, 97 buick riviera Ignition Switch Diagram

1998 Ford F 150/250 Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. Remove the passenger air bag. For additional information, refer to Section 501-20B . 3. Remove the driver air bag. For additional information, refer to Section 501-20B . 4. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Carefully pry to release the (A) clips and remove the (B) steering column opening cover. 5. Position the electrical connector aside. * Release the push clip from the lower instrument panel steering column cover (044F08). 6. Pull to release the three (A) clips and remove the (B) fuse door. 7. Position the hood latch release handle aside. 1. Remove the screws. 2. Position the hood latch release handle aside. 8. Position the parking brake release handle aside. 1. Remove the screws. 2. Position the parking brake release handle aside. 9. If equipped, remove the instrument panel floor duct panel. * Remove the two push clips and release the expander clip. 10. Remove the lower instrument panel steering column cover (04459). 1. Remove the bolts. 2. Remove the lower instrument panel steering column cover. 11. Remove the LH and RH scuff plates. 12. Remove the LH and RH cowl side trim panels. 13. Disconnect the brake pedal position (BPP) switch electrical connector. 14. Remove the (A) radio ground and the (B) GEM/CTM ground bolts. 15. Disconnect the LH instrument panel main harness connectors. 16. Remove the bulkhead wiring harness electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 17. Remove the bulkhead electrical connector from the dash panel. 1. Release the six locking tabs. 2. Remove the bulkhead connector from the dash panel. 18. Disconnect the air bag diagnostic monitor electrical connectors. 19. Disconnect the inertia fuel shutoff switch electrical connector. 20. Remove the RH ground bolts. 21. Disconnect the RH instrument panel main harness connectors. 22. Disconnect the electronic blend door actuator electrical connector. 23. Disconnect the climate control head vacuum harness connector. 24. Remove the instrument panel steering column opening cover reinforcement (04502). 1. Remove the nuts. 2. Remove the instrument panel steering column opening cover reinforcement. 25. Disconnect the air bag sliding contact electrical connectors and the anti-theft sensor electrical connector.

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, kia besta wiring diagram, PIN DATA 2005 скачать, vp44 9 pin connector, what pins are positve and negative on a 40 pin cat ecm

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

Related Content:

Bully Side Step Installation, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, bully side ste for jeep instructions, no powertrain dtc\s or freeze frame data, p1860 tcc pwm solenoid circuit electrical, powertrain generator 6500 owners manual, powertrain generator parts, powertrain generator ptg1000, replace radiator 2000 dodge durango