Skip to content

evap vent valve pic 2002 tahoe

You search PDF repair manual about evap vent valve pic 2002 tahoe, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

download
Tighten Tighten the bracket mounting bolt to 12 N?m (106 lb in). Connect the vent valve pipe to the EVAP canister. • Install the two vent valve pipe clips into the existing underbody holes. • Connect the EVAP canister vent valve electrical connector, if equipped. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. • Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward. • Raise the transmission and reinstall the transmission support. • Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch*points and heat sources. • Lower the vehicle. • 2004-2007 Model Year (Use Service Kit P/N 19152349) Raise the vehicle. Suitably support the vehicle. • Disconnect the EVAP canister vent valve electrical connector. • Disconnect the canister pipe from the vent valve. • Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. • Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end. Crew Cab Short Box Shown Below, Other Configurations Similar Extended Cab Short Box Shown Below, Other Configurations Similar Install the new canister vent valve to the fuel tank clip or mounting bracket. • Cut bulk 5/8″ heater hose to a length of approximately 76 mm (3 in). Install the hose between the vent valve and the canister pipe and secure using clamps. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. •

Test Guidelines for Use of Essential Tool J 41413-200 Evaporative System Tester

download
Non-Enhanced EVAP System Diagnostic Procedure 1. Pinch off or plug the EVAP vapor line to seal the EVAP system. 2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 4. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 5. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 6. Use the remote switch to introduce smoke into the EVAP system for 60 seconds. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located. 7. Inspect the entire EVAP system for exiting smoke using the high intensity white light (J 41413-SPT). Enhanced EVAP System Leak Detection Procedure When diagnosing DTCs P0440, P0442, P0446 and P0455, use the J 41413-200 EEST along with 1. Turn ON the ignition with the engine OFF. 2. Command the EVAP vent valve closed with a scan tool.* *Prizm: In order to seal the EVAP system on the 1998-2002 Prizm, bypass the EVAP canister by connecting the fuel tank vapor hose to the canister purge line. Refer to the Service Information for additional information. 3. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground. 4. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part number. 5. Connect the EEST’s nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter. 6. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE. 7. Use the remote switch to introduce smoke into the EVAP system. 8. Use the J 41413-VLV EVAP Port Vent Fitting tool to open the EVAP service port (if equipped) until smoke is observed. 9. Remove the J 41413-VLV EVAP Port Vent Fitting tool once smoke is observed. Important: Additional smoke may need to be introduced at 15-second intervals until the leak source has been located.

2002 Chevrolet Tahoe – 4WD Fuel Line Disconnect Tool for Fuel Filter Removal/ Installation Procedure on 5.3L Flexible Fuel Engine

download
2. Install the J 34730-1A . 3. Loosen the fuel fill cap in order to relieve fuel tank vapor pressure. 4. Open the valve on the J 34730-1A in order to bleed the system pressure. The fuel connections are now safe for servicing. 5. Drain any fuel remaining in the gauge into an approved container. 6. Once the system pressure is completely relieved, remove the J 34730-1A . 7. Raise and suitably support the vehicle. Important Clean the fuel filter connections and surrounding area before disconnecting the fuel lines in order to avoid possible fuel system contamination. 8. Using a flare nut wrench and a backup wrench, disconnect the fuel line fitting from the fuel filter. 9. Pull the quick-connect fitting back until the internal retainers hit the filter stop. 10. Twist one end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 11. Twist the opposite end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 12. Once the J 46363 – Fuel Line Disconnect Tool is inserted, ensure the tool is parallel to the filter and the fitting. 13. While holding the filter, push the quick-disconnect fitting towards the filter in order to disconnect the quick- connect fitting. 14. Remove the quick-connect fitting from the filter. 15. Remove the filter from the bracket. 16. Install the new fuel filter, P/N 15173334 or P/N 25164003 (A/C Delco P/N GF847), to the bracket. 17. While holding the filter, push the fitting towards the filter in order to connect the quick-connect fitting. 18. Using a flare nut wrench and a back up wrench, connect the fuel line fitting to the filter. 19. Position the fuel sensor bracket into place and install the two nuts. Tighten Tighten the two nuts to 17 N·m(13 lb ft). 20. Lower the vehicle. 21. Tighten the fuel cap. 22. Connect the negative battery cable.

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.