fixing auto temp control in 2002 altima

You search PDF repair manual about fixing auto temp control in 2002 altima, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fixing auto temp control in 2002 altima Direct Download speed 5432 Kb/s

  fixing auto temp control in 2002 altima Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, montero crank shaft pully removal, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, mitsubishi montero sport belt tension bolt pivot, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 1995 accord repair manual pdf, 2003 buick lesabre lose power for instrument panel and a/c controls, 1989 corvette climate control panel, 2005 honda crv malfunction indicator lamp reset, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord 61-10 code, fuel circuit outputs on chevy s10, honda accord code 61-1

1984 Mercedes Benz 190E Fuel Delivery and Air Induction Engine Testing And Adjustment Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 13-04-2012

download
Note: Test and adjust lambda control with a lambda control tester. The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer. Testing, adjusting 1 Complete measurement sheet. 2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”. 3 Read out DTC memory. Note: Not available on model year 1984-1986. 4 Connect testers: oil remote thermometer (018)124 589 07 21 00 lambda control tester (012) twin socket (031) trigger clamp (011) exhaust probe (005)126 589 11 63 00 CO measuring instrument (006) engine tester with oscilloscope (030) multimeter (003) test cable (033)102 589 04 63 00. 5 Position extraction device (014) at exhaust tail pipe. 6 Check engine coolant level, adjust to correct level. 7 Check engine oil level, pay attention to condition of oil (visual inspection). 8 Take off air cleaner. 9 Check ease of movement and condition of throttle control linkage and throttle valve. Grease all bearing points and ball sockets. 10 Check fulcrum lever, adjust. Check whether the roller (15) in the fulcrum lever (13) is resting free of tension against end stop. Adjust fulcrum lever (13) with the connecting rod (2), if necessary, so that the roller (15) is resting free of tension against end stop. 11 Idle stop. Check whether the throttle valve is resting against idle stop. Disconnect connecting rod (2) for this step. Adjust throttle control. Engines with cruise control only. Check whether the actuator is resting against idle stop of cruise control by pressing the lever of the actuator clockwise against idle stop at cruise control. When attaching the connecting rod (21), ensure that the lever of the actuator is lifted approx. 1 mm off the idle stop at the cruise control. Adjust tie rod, if necessary. Adjust throttle control. 12 Check wide open throttle stop from the accelerator pedal , adjust. 13 Voltages Test (battery and ignition coil ): No-load voltage Connect voltmeter to the battery, paying attention to the polarity, and take reading of voltage. Specification: 12.2 volts . Ignition coil Switch on ignition with engine not running. Test the voltage terminal 15 to ground at contact 5 of diagnostic connector. Specification: battery voltage Test difference in voltage between terminal 15 and terminal 1 at contacts 5 and 4 of diagnostic connector. Specification: 0 volts If the specified values are not reached, test

Related Content:

throttle control motor relay 05 mazda 3, 1986 190e 2 3 crank trigger test, 2007 Dodge Throttle Valve Actuator Installation Instructions, ax4n endplay pdf, carborator for mazda6 2003 manual gear, how to test actuator of stabilator, how to test throttle actuator motor, mb 1993 lamda code, throttle position sensor 1986 190e 16 valve

2002 NISSAN ALTIMA MANUAL A/C TEMPERATURE NOT ADJUSTABLE REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 11-05-2012

download
SERVICE PROCEDURE 1. Remove the following components; • cluster lid “C” (HVAC control surround trim) • fuse box cover • driver’s side instrument panel lower cover (attached with 2 screws). 2. Remove the screw from the center of the cable operated gear (see Figure 2). Figure 2 3. Locate the small (about 1″ dia.) white air mix door gear. Hopefully it is still on the floor. NOTE: If you cannot find the old air mix door gear, order a new gear. Refer to the Parts Information section of this bulletin. 4. To see how it is supposed to fit, temporarily install the gear into the air mix door shaft (see Figure 3). Figure 3 Air mix door drive gear (shown installed) Heater box Cable operated gear Retaining screw (remove) Front TP020106 Cable (do not detach) On the left side of the heater case, remove the screw from the center of the cable operated gear for the air mix door. Note: It is not necessary to detach the cable from the gear or the heater box. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. Front TP010607a The gear can fit two different ways, only one of which is correct. Install the gear and rotate the gear/mix door shaft assembly fully clockwise so the gear’s index pin is at the 2 to 3 o’clock position. Cable (do not detach) Note: If the gear is in the correct spot, the alignment pin will be at the 2 to 3 o’clock position. POSITIONING THE GEAR CORRECTLY IS CRITICAL TO GETTING THE DOOR TIMING RIGHT. 3/5 5. Remove the gear, thoroughly clean the gear shaft of any grease, and apply the glue. See Figure 4. Figure 4 6. Re-install the gear into the mix door shaft (see Figure 5). Figure 5 TP010606a Air mix door gear (back side) Apply Glue to Shaded areas b. Apply plastic glue (3M dp-8005 or equivalent) to the shaft of the air mix door gear in the area where it inserts into the air mix door shaft. a. Thoroughly clean the air mix door gear shaft. Note: It is not necessary to clean the grease from the gear teeth. Front TP020100 Re-install the gear so the gear’s index pin is at the 2 to 3 o’clock position when the gear/mix door shaft assembly is turned fully clockwise. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. 4/5 7. Set the HVAC control temperature dial as shown in Figure 6. Figure 6 8. Re-install the cable operated gear (see Figure 7). Figure 7 9. Operate the temperature control while watching the air mix door gear movement. They should operate freely with no binding. 10.Check the adjustment of the temperature cable as follows: A. Rotate the temperature control knob to the full COLD position (i.e., fully counterclockwise) and confirm the air mix door is fully seated (sealed) in the down position, then B. Rotate the temperature control knob to the full HOT position (i.e., fully clockwise) and confirm the air mix door is fully seated (sealed) in the up position. If the air mix door does not fully seat (seal) in either the full HOT or full COLD position: • Adjust the temperature control cable, with the temperature control knob in the full hot position, using the clip at the heater unit (see Figure 7) 11.Re-install the trim pieces removed in step 1.

Related Content:

how to check the backlash between the camshaft gear and the adjustable idler gear for 3406 e monel, used set of pistons for 2000 nissan altima with2 2, how to fix a shifter in a 2000 chevy malibu, VVTI GEAR POSITION DETERMINED BY CAM SENSOR WAVEFORM, how to change shift boot hummer h3, how to align cd4e mlp sensor, how do i replace the rear differential seal in my 2006 kia sorento ex 4wd, hino so5d gears, Gear shift nob broken on 2000 Chev Malibu, gear selector for 00 rodeo only goes in first and reverse

1988-1996 TOYOTA PICK-UP LOWER CONTROL ARMS INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
1) Park your truck on flat level surface. Chock the rear wheels. Loosen front lug nuts. Raise the front with a floo jack. Support the frame with jack stands. Remove front wheels. NOTE : ALWAYS USE JACK STANDS – NEVER RELY ON JACKS ONLY!! 2) Starting on the drivers side, locate the height adjusting bolt at the rear of the torsion bar. Measure and record the length of the threads exposed between the end of the adjusting bolt and jam nuts (Fig. A). Now make a mark at the front of the torsion bar, where it goes into the bracket bolted the lower control arm. Mark bath the bar and the bracket (Fig. B). This will index the bar into the correct position when installing. Fig. A Fig. B Note : Step #2 assumes torsion bars are in the factory position. 3) Loosen the height adjusting bolts until there is no longer any load on the torsion bars. 4) Remove the 2 bolts that hold the tensioncompression rod and sway bar end link bolts. 5) Now remove the two bolts on each arm that holds the torsion bar receiver to the back of the control arm. Slide the torsion bar and receiver back from the control arm. There is a wide spline on the torsion bar corresponding to the double width tooth on the torsion bar receiver. The receiver will not slide back onto the bar if the splines are not aligned properly. 6) Loosen and remove the 3 nuts and bolts that hold each ball joint to the lower control arms. 7) Remove the pivot bolts holding the lower control arm to the frame and remove control arm from truck. 8) Unbolt and remove original bump stops from factory arms and bolt them to you new DJM control arm. 9) Drill out the small hole on the end of the torsion bar receiver to 7/16″on both sides. This is to accept the 7/16″ x 5- 1/2″ bolt supplied. 10) Compare the new DJM control arms with the factory ones. Carefull note the diameter of the factory ball joint mounting holes. You will find either three 10mm hole used on most earlier models or larger 13mm holes on late models. If you factory arms have the 10mm holes continue to step # 10. If factory holes are 13mm it will be necessary to enlarge the holes with a 1/2″ drill bit(Fig. C). Fig. C 11) Mount the DJM control arms to the truck. Make sure the steering stops are facing the front of the truck. Insert the pivot bolts and install the washers and nuts. DO NOT TIGHTEN YET . 12) Bolt on the tensioncompression rods to the lower control arms. It mat be necessary to loosen the large nuts that hole the tensioncompression rods to the frame in order to rotate the rods to the proper angle to align bolts into control arms.

Related Content:

arm cam download

2002 Volvo XC70 Rear Wheel Hub Replacing Removal and installation manual

0

Filed Under (Volvo Manuals) by admin on 17-05-2011

download
Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame. Bend the control arm downwards. Remove the screws from rear wheel hub the rear wheel hub from the wheel spindle and drive shaft. Note: Clean the splines on the drive shaft before installing the new wheel hub. Lubricate the splines using oil. Installing the rear wheel hub Note: Ensure that the hub and the wheel spindle mating surfaces are clean. Install the rear wheel hub. Use new screws and torque wrench with ring wrench kit. Tighten crosswise. Tighten to 20 Nm . Then tighten to 65 Nm . Finally angle-tighten 60° . Use bevel protractor 951 2050. the control arm to the sub-frame. Do not tighten yet the tie rod on the wheel spindle. Do not tighten yet. Install the anti-roll bar link to the upper control arm. Tighten to 80 Nm . Use a Torx wrench as a counterhold so that the boot is not damaged. Press the suspension up to its normal position

Electric Trailer Brake Controller Installation Manual

0

Filed Under (More Manuals) by admin on 10-05-2012

download
In connection with the installation of such devices, please note the following. 1. Check the installed rear SAM. If a rear SAM with part number A164 540 78 45 or A164 540 88 45 is currently installed, a new rear SAM must be installed and version coded. The current part number is listed in the parts information section below. The cost of this update is not covered by warranty. Note: Some vehicles without a factory trailer hitch are equipped with a rear SAM that requires replacement with a different rear SAM if trailer brakes are to be retrofitted. 2. Locate plug X58/28. This contains the four wires needed for the electric trailer brake controller Refer to the below for wire description. a. Up to December 2006 production, X58/28 (Figure 1, green plug) near the rear fuse box F4 (Figure 1). Plug may be tie wrapped to harness below Rear SAM. b. As of December 2006 production, X58/28 (Figure 2, green plug) near the diagnostic connector X11/4 (Figure 2). Plug may be tie wrapped to harness above connector X11/4. Figure 1 T-B-31/1907 Figure 2 T-B-31.19/07d Wire Description – X58/28 Color Size Description Red or Red /Blue 2.5 mm2 Fuse F4f71, 30 Amp fuse. This is the power supply for an electric trailer brake controller. Brown 2.5 mm2W7 ground. This is the ground wire for an electric trailer brake controller Grey or Black/Red 0.75mm2 Brake light circuit. This is the brake signal for an electric trailer brake controller (input to the electronic brake controller). Yellow/Red or Yellow/White 2.5 mm2 X58/11 pin 7. This is the variable voltage signal to actuate the trailer brakes (from the output of the electronic brake controller). Note: Most electric trailer brake controllers specify that the power supply must be wired using a self resetting circuit breaker. Follow the instructions supplied with the electric trailer brake controller. Note: The above variation in wire colors depends on production date of factory harness and or installed accessory harness. Warning! The electric trailer brake controller must be adjusted according to the instructions supplied with the electric trailer brake controller, which requires the trailer be connected to the tow vehicle

Related Content:

A164 540 88 45, 2006 dodge ram ac electrical diagrams, a164 690 02 10, highlander pop up camper fuse box

2002 Daewoo Leganza SE Dashboard / Instrument Panel Service and Repair Manual

0

Filed Under (Daewoo Manuals) by admin on 02-02-2012

download
Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the floor console. 3. Remove the sun sensor and the automatic temperature controls assembly. 4. Remove the tweeter speakers and the stereo cassette AM/FM radio. Refer to Section 9F, Audio Systems. 5. Remove the screws and the instrument panel storage compartment. 6. Remove the instrument cluster dimmer switch assembly. 7. Remove the instrument cluster. 8. Remove the chime module. 9. Remove the kick panels. 10. Remove the glove box. 11. Remove the screws and the glove box housing. 12. Disconnect the glove box housing electrical connectors. 13. Remove the knee bolster. 14. Remove the nuts and the bolts securing the steering column. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 2 15. Disconnect the steering column electrical connectors. 16. Lower the steering column. 17. Remove the screw behind the stereo cassette AM/FM radio. 18. Remove the screw securing the instrument panel to the heater air distributor case. 19. Remove the bolts and the glove box brace. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 3 20. Remove the instrument panel screw behind the glove box brace. 21. Remove the instrument panel bolts below the windshield. 22. Remove the bolts securing the bottom of the instrument panel to the floor. 23. Remove the bolts securing the sides of the instrument panel to the body. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 4 24. Disconnect the instrument panel electrical connectors. 25. Remove the instrument panel. Installation Procedure 1. Position the instrument panel in the vehicle. 2. Connect the instrument panel electrical connectors. NOTE: Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion. 3. Install the bolts securing the sides of the instrument panel to the body. Tighten Tighten the instrument panel-to-body bolts to 22 N.m (16 lb-ft) . 4. Install the bolts securing the bottom of the instrument panel to the floor. Tighten Tighten the instrument panel-to-floor bolts to 22 N.m (16 lb-ft) .

Related Content:

toyota matrix 2003 evaporator removal, take dashbord daewoo leganza, how to remove headliner from cadillac escalade ext 03, daewoo 1760xl service manual, diy brass instrument repair tools, 2002 saturn sl2 owners manual, nissan sentra 02 2 5 cam torque, p1627 daewoo, 2002 daewoo lanos code, 2 2 dtec deewoo engine timing marks

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram