ford 3 8 v6 camshaft binding

You search PDF repair manual about ford 3 8 v6 camshaft binding, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford 3 8 v6 camshaft binding Direct Download speed 5432 Kb/s

  ford 3 8 v6 camshaft binding Full Version speed 8172 Kb/s



2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

0

Filed Under (Toyota Manuals) by admin on 27-04-2012

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

Related Content:

2008 saturn vue v6 camshaft position actuator solenoid location, www pdfrepairmanual com/search/toyota 1g fe engine, toyota 1g fe vvt-i engine service manual, user manual engin 3s pdf free dowenload, user manual engine 3s pdf free download, vsv satrun, 1g-fe camshaft timing marks /pdf, toyota 1G fe engine tightening torque specs, scionxb actuator problems, toyota 1g-fe engine repair manual

3406E TRUCK ENGINE 2WS Camshaft Gear Removal And Installation Manual

0

Filed Under (More Manuals) by admin on 28-05-2012

download
1. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 2. Remove top bolt (2) from camshaft gear (1) . Install Tooling (A) in place of the bolt. 3. Remove remaining bolts (2) and remove camshaft gear (1) . 4. NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. Remove Tooling (A) . 5. Installation Procedure Required Tools Tool Part Number Part Description Qty A 9U-6896 Guide Bolt 1. Align the hole in the back of camshaft gear (1) with the dowel in the adapter. Install camshaft gear (1) over Tooling (A) . Note: Camshaft timing is critical. The timing mark on the camshaft gear must be aligned with the timing mark on the front cover when the No. 1 piston is at the top center of the compression stroke. Refer to Testing and Adjusting, “Gear Group (Front) – Time”. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 3. Note: If the timing marks are not aligned, remove camshaft gear (1) and rotate the camshaft until the timing marks are aligned. Install bolts (2) . Remove Tooling (A) and install remaining bolt (2) . 4. 5. Check the backlash between the camshaft gear and the adjustable idler gear. The backlash should be 0.216 ± 0.114 mm (0.0085 ± 0.0045 inch). Refer to Testing and Adjusting, “Gear Group (Front) – Time” for the backlash adjustment procedure. 6. End By: Install the front cover. Refer to Disassembly and Assembly, “Front Cover – Install”

Related Content:

volvo s40 cam alignment instructions, 3406e front cover removal, 3406e timing gear backlash, c15 cam gear backlash, Cat C15 rotation, mazda timing marks 1991 mx6

Ford V6 And V8 Timing Set Installation Instructions

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Installation Instructions 1. Clean everything! Make sure that the engine mounting surfaces and your new timing set have been thoroughly cleaned with a good solvent. 2. If you are using a timing set with three keyways, select the appropriate keyway for your camshaft timing specifications. COMP Cams ® recommends the standard timing position for most applications. This position uses the round or “O” timing and keyway marks. Standard Timing Location: This is the same as original O.E.M. setting. Use keyway and crankshaft gear tooth marked “O”. É 4 Degree Advance: Use keyway and crankshaft tooth marked . Note: The or advanced position should not be used without degreeing the camshaft. Many camshafts have the proper advance built in. Advancing the cam will reduce intake valve to piston clearance and increase exhaust piston to valve clearance. É 4 Degree Retard: Use keyway and crankshaft gear tooth marked . Note: The or retarded position should not be used without degreeing the camshaft. Many cams have the proper advance built in. Retarding the cam will reduce exhaust valve to piston clearance and increase intake piston to valve clearance. 3. Install your lower timing gear on the crankshaft making sure that the timing marks are facing out toward you. 4. Now that the lower timing gear has been installed check the timing mark alignment in your engine manual. Rotate the crankshaft using your crankshaft socket until the timing mark on the gear is in the proper position (12 o’clock). For 240-300 6 cyl. see Note 1 before proceeding! 5. If your engine is equipped with a camshaft retaining plate or thrust plate, it should be installed at this time. Note that many Ford thrust plates are marked “back – bottom”. Before final installation check to make sure that the thrust plate is fitted correctly. 351W owners see Note 2 before proceeding! 6. Temporarily install your camshaft timing gear and rotate the camshaft until the timing mark on the camshaft gear is in the proper position per your engine manual instructions (6 o’clock) Ford Timing Set Installation Instructions

1985 -1995 5.0L Ford V8s with Hydraulic Roller Lifter Cams ACCU-DRIVE CAM GEAR DRIVE SYSTEM Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-01-2012

download
1. Remove stock timing cover. Rotate engine to Top Dead Center of cylinder #1 so that the timing marks on the original crank and cam sprockets are directly lined up with each other, i.e. the mark on the crank sprocket will be straight up and the mark on the cam sprocket will be straight down. Using suitable gear puller, remove stock crank and camshaft sprockets and timing chain. Refer to repair manual if necessary for individual steps. 2. Assemble Accu-Drive as shown in Figure 1. 3. Install crank gear with the large inside chamfer toward rear of engine and timing mark toward front of engine. Make certain crankshaft drive key is aligned with keyway of the crank gear before assembling. 4. See Figure 2 “Camshaft Gear Assembly”for correct assembly. (a) Place well-lubricated thrust washer on the rear (block) side of cam gear. (b) The Edelbrock Accu-Drive system is furnished with an 0.032″ thick thrust ring that installs between the back side of the cam gear and the front side of the camshaft thrust plate. Torque the thrust plate retaining capscrews to 9-12 ft./lbs. NOTE: No thrust button is used on Ford engines. (c) Select the desired keyway in the crank gear “0″ (standard), “A” (4ºadvanced at the crank, 2º at the cam), or “R” Place a small amount of clay on the front end of both axles as shown in Figure 3. NOTE: It will be necessary to cut material off rib inside front cover to hold idler gears in place. (b) Install front cover with gasket in place. (c) Remove cover and measure the thickness of the compressed clay. It should be .005″-.030″. Do not tighten cover down until proper clearance has been obtained. Without sufficient clearance, there is risk of cracking the cover when tightened down. (d) If clearance is less than .005, you will need to grind off idler axle as shown to obtain proper clearance. If clearance is greater than .090, replace left side (larger idler side) stud with tapered end axle provided in the kit. Re-install idler assembly and recheck for minimum clearance between block and front cover. 8. With all gears correctly in mesh and timed, tighten the camshaft capscrew to 35 ft./lbs. It would also be a good idea to use Locktite™ or equivalent on the bolt threads prior to final assembly. 9. Lubricate all gears and bearings with engine oil. 10. Re-install the front cover. 11. Re-install all components removed in preparation for step 1

Related Content:

P30 bellcrank assy, 1989 ford escort 1 3 thrust washer end play, 1995 ford 6 cylinder cam gear marks, ford 200 camshaft

Ford V8 Engines Performer RPM Hydraulic Roller Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 01-01-2012

download
Disconnect the battery. 2. Drain radiator coolant. Drain plug will normally be located on lower right or left side of the radiator facing the engine. 3. Remove radiator and air conditioning condenser if so equipped. In some cases, the front grill may have to be removed. Measure distance from front cover to grill or brackets that may interfere with camshaft against the length of the camshaft. 4. Remove the gas cap to relieve pressure. Disconnect fuel line and plug. Replace gas cap. 5. Disconnect all linkage from carburetor such as throttle, throttle springs, transmission, cruise control and automatic choke. 6. Tag and remove coil wires and sensor wires. 7. Tag and remove vacuum lines. 8. Remove valve covers. 9. Remove distributor cap and wires, rotate engine until rotor points towards number 1 terminal in cap and pointer on front cover is on top dead center (TDC) and remove distributor. (see Fig. 1) Note: Mark the approximate position of the distributor housing in relation to the manifold to assist in getting the distributor properly located during re-installation. 10. Remove carburetor and intake manifold. Remove and discard intake manifold gasket. 11. Remove rocker arms and pushrods. CAUTION: If your engine has non-adjustable rocker arms (1969-1/2 or later), you must install screw-in studs and high performance •VALVE SPRINGS CAUTION: WARNINGS ABOUT YOUR WARRANTY In order for this Performer RPM roller cam to be covered under ANY WARRANTY, you MUST use the correct Valve Springs. Failure to install the correct valve springs may cause lifters not to follow the cam lobes and damage engine parts. This camshaft is designed to function with valve springs that have a closed pressure of 110 lbs, open pressure of 320 lbs and a lift of .575″. Special H.P. retainers may be necessary with your installation for proper spring height. Do not use rotator type valve springs or retainers for this application. Note: Edelbrock Sure Seat Valve Springs #5762 are not recommended.  IMPORTANT NOTES AFFECTING YOUR WARRANTY CAM LOBE DAMAGE – Cam lobe wear is almost non-existent unless mismatched parts are used or installation of the cam and lifters is done improperly. Cam damage can result from the timing gear loosening due to improper torque on bolts. Bolts holding gear to camshaft should be torqued carefully and a locking compound applied to threads of bolts. Before installing your new Performer-RPM roller camshaft, check the gear drive on the distributor and oil pump for any signs of wear. If worn, be sure to replace with a new gear or you may wear out your camshaft prematurely. High-pressure oil pumps are not recommended with Performer RPM roller camshafts. Edelbrock camshafts are designed to use with Edelbrock timing chains.  CAM GEARS AND CAMSHAFT END PLAY- If cam gear becomes loose, the cam will slide back in the block, causing the lifters to hit the lobes next to them and also the cam bearing journals. If the engine is run after this happens, the bottom of the lifters and the sides of the lobes will become damaged. See Installation Instructions section for end play specifications.  LIFTERS Edelbrock offers a retrofit roller lifter kit for engines not originally equipped with roller lifters. Use part #97453. To install your roller lifters, use fresh clean oil on the lifter and the lifter bore just prior to installing. The guide bar (high side of tappet) must face the opposite side of block. See roller lifter instructions for additional information. ( Note: 289-302 engines require removal of the cylinder heads to provide enough clearance to install roller lifters, which are taller than standard hydraulic lifters.)  PUSHRODS AND ROCKER ARMS High performance pushrods, roller rocker arms and rocker studs are recommended for this installation. After the cam is installed and timed correctly (see Figure 2), it will be necessary to check each pushrod for correct lifter preload. INSTALLATION INSTRUCTIONS 1. Check lifters as covered in Lifters section. Coat cam lobes with fresh clean oil. Lube distributor drive of cam with assembly lube (supplied). 2. Install new camshaft. Re-install thrust plate with new sprockets and timing chain with timing marks lined up as recommended by factory specifications (See Figure 2). Reinstall the fuel pump eccentric before installing sprocket bolt and washer

Related Content:

roller lifters trouble 2010 gmc, 2006 DT466 lifters, 5 3 camshaft problems, Ford 2003 4 liter V6 camshaaft bolt torque, ford 302 camshaft endplay, rear cam bolt torque 4 0 sohc, sun distributer machines parts, torque side trrminal battery, v6 3000 four cam 24 vvt-i thermostat location

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

How to Fix Po446 Code ford escape xls, 555 ford backhoe repair manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, Ford E 450 Cutaway Manual, ford 9 inch repair manual, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, Ford OBD1 Codes and Fixes for Them, how many quarts of transmission fluid does 2012 ford e450 take?

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

1997 Ford Truck F 150 2WD Engine/ Timing Chain/ Cooling and Exhaust Installation Manual

0

Filed Under (Ford Manuals) by admin on 31-01-2012

download
installation Notes NOTE: Ford does not provide a procedure to align the timing components without the OE tools specified. 1. Compress the tensioner plunger, using an edge of a vise. CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result. Do not compress the ratchet assembly. This will damage the ratchet assembly. 2. Use a small screwdriver or pick to push back and hold the ratchet mechanism 3. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing. 4. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation. 5. Remove the tensioner from the vise. 7. If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks. 8. Loosely install the Camshaft Holding Tools on both camshafts 9. Install the timing chain guides . 10. Rotate the LH camshaft with the Camshaft Positioning Tool until the timing mark is approximately at 12 o’clock. Rotate the RH camshaft with the Camshaft Positioning Tool until the timing mark is approximately at 11 o’clock. Tighten the Camshaft 11. Position the crankshaft with the Crankshaft Holding Tool. CAUTION: Unless otherwise instructed, at no time when the timing chains are removed and the cylinder heads are installed is the crankshaft or camshaft to be rotated. Severe piston and valve damage will occur. Rotate the crankshaft counterclockwise only. Do not rotate past position shown or severe piston and/or valve damage can occur. 12. Remove the Crankshaft Holding Tool. Zoom Sized for Print Zoom Sized for Print Fig. 26 Crankshaft Sprocket Position

Related Content:

La Z Boy Recliner pawl release, la-z-boy pawl and ratchet assembly

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

0

Filed Under (Ford Manuals) by admin on 20-01-2012

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

Related Content:

1997 Ford Explorer Repair Manuals, 2011 Chevy Cruze P057c Code, ford explorer Front Axle Clunking, pid default parmameters for 2007 ford explorer, po57c

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

Related Content:

2008 saturn vue v6 camshaft position actuator solenoid location, www pdfrepairmanual com/search/toyota 1g fe engine, toyota 1g fe vvt-i engine service manual, user manual engin 3s pdf free dowenload, user manual engine 3s pdf free download, vsv satrun, 1g-fe camshaft timing marks /pdf, toyota 1G fe engine tightening torque specs, scionxb actuator problems, toyota 1g-fe engine repair manual