ford 5 0 gear drive instructions

You search PDF repair manual about ford 5 0 gear drive instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford 5 0 gear drive instructions Direct Download speed 5432 Kb/s

  ford 5 0 gear drive instructions Full Version speed 8172 Kb/s



2002 NISSAN ALTIMA MANUAL A/C TEMPERATURE NOT ADJUSTABLE REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 11-05-2012

download
SERVICE PROCEDURE 1. Remove the following components; • cluster lid “C” (HVAC control surround trim) • fuse box cover • driver’s side instrument panel lower cover (attached with 2 screws). 2. Remove the screw from the center of the cable operated gear (see Figure 2). Figure 2 3. Locate the small (about 1″ dia.) white air mix door gear. Hopefully it is still on the floor. NOTE: If you cannot find the old air mix door gear, order a new gear. Refer to the Parts Information section of this bulletin. 4. To see how it is supposed to fit, temporarily install the gear into the air mix door shaft (see Figure 3). Figure 3 Air mix door drive gear (shown installed) Heater box Cable operated gear Retaining screw (remove) Front TP020106 Cable (do not detach) On the left side of the heater case, remove the screw from the center of the cable operated gear for the air mix door. Note: It is not necessary to detach the cable from the gear or the heater box. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. Front TP010607a The gear can fit two different ways, only one of which is correct. Install the gear and rotate the gear/mix door shaft assembly fully clockwise so the gear’s index pin is at the 2 to 3 o’clock position. Cable (do not detach) Note: If the gear is in the correct spot, the alignment pin will be at the 2 to 3 o’clock position. POSITIONING THE GEAR CORRECTLY IS CRITICAL TO GETTING THE DOOR TIMING RIGHT. 3/5 5. Remove the gear, thoroughly clean the gear shaft of any grease, and apply the glue. See Figure 4. Figure 4 6. Re-install the gear into the mix door shaft (see Figure 5). Figure 5 TP010606a Air mix door gear (back side) Apply Glue to Shaded areas b. Apply plastic glue (3M dp-8005 or equivalent) to the shaft of the air mix door gear in the area where it inserts into the air mix door shaft. a. Thoroughly clean the air mix door gear shaft. Note: It is not necessary to clean the grease from the gear teeth. Front TP020100 Re-install the gear so the gear’s index pin is at the 2 to 3 o’clock position when the gear/mix door shaft assembly is turned fully clockwise. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. 4/5 7. Set the HVAC control temperature dial as shown in Figure 6. Figure 6 8. Re-install the cable operated gear (see Figure 7). Figure 7 9. Operate the temperature control while watching the air mix door gear movement. They should operate freely with no binding. 10.Check the adjustment of the temperature cable as follows: A. Rotate the temperature control knob to the full COLD position (i.e., fully counterclockwise) and confirm the air mix door is fully seated (sealed) in the down position, then B. Rotate the temperature control knob to the full HOT position (i.e., fully clockwise) and confirm the air mix door is fully seated (sealed) in the up position. If the air mix door does not fully seat (seal) in either the full HOT or full COLD position: • Adjust the temperature control cable, with the temperature control knob in the full hot position, using the clip at the heater unit (see Figure 7) 11.Re-install the trim pieces removed in step 1.

Related Content:

how to check the backlash between the camshaft gear and the adjustable idler gear for 3406 e monel, used set of pistons for 2000 nissan altima with2 2, how to fix a shifter in a 2000 chevy malibu, VVTI GEAR POSITION DETERMINED BY CAM SENSOR WAVEFORM, how to fix a broken column shifter on a 2003 toyota sequoia, how to change shift boot hummer h3, how do i replace the rear differential seal in my 2006 kia sorento ex 4wd, Gear shift nob broken on 2000 Chev Malibu, gear selector for 00 rodeo only goes in first and reverse, how to fix a loose metal knob control panel on a window whirlpool room ac

RICHMOND GEAR INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 19-03-2012

download
VERIFY RATIO BEFOREASSEMBLY STEP 1 . Remove the gears to be replaced and thoroughly clean both the gear carrier and housing with solvent to remove any gear/bearing residue, which could lead to abrasive failure of the new gear set. After cleaning, dry- wipe (or air-dry) all disassembled parts, housings, and covers. STEP 2. Examine the ring gear mounting surface for nicks or burrs which might prevent total landing of the newly installed ring gear. Ring/pinion tooth depth variations can result from a ring gear that is “cocked”on its mounting surface. If a ring gear spacer is to be used, also check it for similar surface imperfections, dressing these with block backed pieces of grit paper or a small file. Following material removal (from ANY part of the assembly), bathe the pieces in the solvent and wipe or air-dry. NOTE: Spacers not normally recommended STEP 3. Study the illustrations provided with these instructions. Familiarize yourself with the terms “backlash”and “pinion depth” (sometimes called checking distance). Each set of gears is a matched pair which has been prerun on a gear test machine. Consequently, the pair should never be mixed with other rings or pinions, Also, since all gear sets have been run-checked, specific settings are supplied with each ring/pinion pair. These specifications vary from set to set. Backlash settings are marked on the outside diameter face of the ring gear as follows (see illustration A): Ref: BL.008, which means a backlash figure of .008 inch at the closest point. Pinion depth settings (or checking distance) are marked on the face of the pinion gear as follows (see illustration B): Ref: CD 2.799, which means distance of 2.799 inches from centerline of the ring gear to pinion face. Dimensional variations for backlash SHOULD NOT EXCEED .004″variation. Example: If backlash is .008, the backlash — including maximum variation — should be .008-.012. 1 Illustration B Location of checking distance (pinion depth) & serial no. on pinion Location of backlash dimension & gear serial no. on ring gear Illustration A STEP 4. When installing the pinion gear you must check its depth in the housing as per the pinion depth dimension. Add or subtract pinion depth shims to arrive at the checking distance etched on the surface of the pinion face. (See illustration C.). Refer to Helpful Hints & Additions to Richmond Gear Installation Instructions on pages 3 and 4. STEP 5. Using a mew crush collar or preload shim pack, set the pinion rotating torque to 10-15 (used bearings) 20-25 (new bearings) inch pounds. For oval track applications when not using a cooling pump, set at 16- 17 inch pounds on new bearings and 10 inch pounds maximum on used bearings. STEP 6. After correct installation of the pinion gear, position the ring gear and check for backlash. Mount a magnetic-base dial indicator on the axle housing in such a way that the indicator plunger will be moving in a line that is tangent to rotation of the ring gear. This will provide you with a backlash reading which should conform to the figure etched on the side of the ring gear. Again, maintain a tolerance of .004 variation. Example: If backlash is .008, the backlash – including maximum variation – should be .008-.012. (Backlash is always measured in 3 or more places equally spaced around in the ring gear.) Note: For oval track racing set BL at approximately .012-.014 inches. STEP 7. Compensation for variations in this setting can be made by side-adjustment of the ring gear. Adjusting rings or side-shim packs can be changed to bring the backlash and rotating torque figures into tolerance. (Use same torque on gear bearings as on pinion bearings.) You are now ready to check the tooth contact pattern to assure that no accidental departures from the factory- marked specifications have been made. Apply a thin coat of RICHMOND GEAR compound (“Part # 55-0001- 1″) on gear teeth for best results. Tooth contact patterns should comply with those shown on next page. (Note rounded or bullet nose shape at heel end of pattern on Gear drive sides). See page 4 for patterns and additional installation hints

Related Content:

gear backlash procedure for cat, how to remove 2007 eatc o ringgs, governor install stanadyne injection, Richmond Gear Installation, pinion checking distance, 580 e ring gear full set, FORD DIFFERENTIALS: HOW To adjust heel toe pinion and ring gear, checking pinion depth, caterpillar transmission backlash tool, 97 grand am horn assembly replacement

Toyota T50 5 Speed Transmission Electronic Speedo Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 19-04-2012

download
I have intentionally left the photos large, to try to clarify any detail I did not explain in the text. This modification DOES require the use of a lathe, I have tried to write it so as to allow you to go to your local machine shop, brother in law, mate or anyone with a lathe…and it will be done correctly Much thanks to John O’Rielly (PLAGER 7) in Brisbane for passing on the information and problems he had with this modification. Fig.1Standard Drive Assemblies T50 left and AE101 right T50 Speedo Drive Adaption Rev 1 Feb 2003 2 Step One:- Dissassembly T50 Drive:- Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime. Fig.2 T50 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 3 AE101 Drive:- Disassembly is similar to T50, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. Fig.3 AE101 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 4 Step Two:- Shortening the Drive Shaft Drive Shaft:- The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm) . Fig.4 Drive Shaft Depth Std AE101 Shaft & Housing The T50 drive shaft will need to be shortened to give the same depth as measured in Fig.4. When I did mine, (and a few others), I found I needed the T50 shaft to be 68.0mm long. Fig.5 Fig.6 The drive shaft is hardened, so I used a belt linisher to shorten the shaft, it could as easily be done on a fine grinding wheel. Remember slowly does it, regular checks of depth in housing and do not let the shaft get too hot during grinding/linishing, this will affect the heat treatment and consequently affect the strength of the drive dogs on the shaft end. Carefully deburr and chamfer, end detail should be similar to original AE101

Related Content:

ax4n endplay specification, 1997 dodge ram 1500 tailshaft diagram, manually disengage 4 wheel drive in durango, drive cycle for toyota corolla 2001, Driveshaft for 2002 Ford F-150 diagram, expidition drive shaft retaining bolts, 2008 ford f150 driveshaft, toyota tundra 2000 4 wheel drive diagnosis, 08 KIA SORRENTO CENTER BEARING, repairing rear pinion oil seal 2002 ford explorer sport trac 2wd

2005 Ford F-150 Drive Pinion Flange and Drive Pinion Seal Repair Manual

0

Filed Under (Ford Manuals) by admin on 21-04-2012

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 . 2. Remove the brake disc. For additional information, refer to Section 206-04 . 3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation. 4. Remove the 4 driveshaft flange bolts. 5. NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange. ? Using mechanic’s wire, position the driveshaft aside. 6. Using a Nm (lb-in) torque wrench on the pinion nut, record the torque required to maintain rotation of the pinion gear through several revolutions. 7. Using the special tool to hold the pinion flange, remove and discard the pinion nut.2005 F-150 Workshop Manual 8. Index-mark the pinion flange in relation to the drive pinion stem to make sure of correct alignment during installation. 9. Using the special tool, remove the pinion flange. 10. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed. Installation 1. Lubricate the new drive pinion seal with grease. 2. Using the special tool, install a new drive pinion seal. 3. Lubricate the pinion flange splines with axle lubricant. 4. NOTE: Disregard the scribe marks if a new pinion flange is being installed. Align the pinion flange with the drive pinion shaft. 5. Using the special tool, install the pinion flange. 6. l a new pinion nut with the same iginal if not replacing the collapsible spacer. If a installed, install the nut in the kit, as indicated in the chart below, or damage to the component may occur. Position the new pinion nut. Pinion Nut 7. no circumstances ut to be backed off to reduce drive pinion bearing preload. If reduced drive pinion bearing preload is required, a new drive pinion collapsible spacer and pinion nut must be installed or damage to the component may occur. NOTE: Remove the special tool while taking drive pinion bearing preload readings with the Nm (lb-in) torque wrench. Using the special tool to hold the pinion flange, tighten the pinion nut. ? Rotate the drive pinion occasionally to make sure the drive pinion bearings are seating correctly. ? Install a Nm (lb-in) torque wrench on the pinion nut. ? Rotating the drive pinion through several revolutions, take frequent drive pinion bearing preload readings until the original recorded drive pinion bearing preload reading is obtained. ? If the original recorded drive pinion bearing preload is lower than specification, tighten to the appropriate specification for used drive pinion bearings. If the drive pinion bearing preload is higher than specification, tighten the pinion nut to the original reading as recorded. For additional information, refer to the Specification portion of this section. 8. Position the driveshaft and align the index mark on the pinion flange.

Related Content:

guide differential f53 1997, replacing 94 camaro rack and pinion, how to repair noise driveshaft in a ford expedicion 2001, cummins n14 accessory drive torque specs, cost to replace a rack and pinion on 2002 suburban, 2004 ford f150 yoke, meritor pinion seal installer, mercedes exhaust pipe torque spec, mercury drive shaft socket, how to change rack and pinion 05trailblazer

1985 -1995 5.0L Ford V8s with Hydraulic Roller Lifter Cams ACCU-DRIVE CAM GEAR DRIVE SYSTEM Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-01-2012

download
1. Remove stock timing cover. Rotate engine to Top Dead Center of cylinder #1 so that the timing marks on the original crank and cam sprockets are directly lined up with each other, i.e. the mark on the crank sprocket will be straight up and the mark on the cam sprocket will be straight down. Using suitable gear puller, remove stock crank and camshaft sprockets and timing chain. Refer to repair manual if necessary for individual steps. 2. Assemble Accu-Drive as shown in Figure 1. 3. Install crank gear with the large inside chamfer toward rear of engine and timing mark toward front of engine. Make certain crankshaft drive key is aligned with keyway of the crank gear before assembling. 4. See Figure 2 “Camshaft Gear Assembly”for correct assembly. (a) Place well-lubricated thrust washer on the rear (block) side of cam gear. (b) The Edelbrock Accu-Drive system is furnished with an 0.032″ thick thrust ring that installs between the back side of the cam gear and the front side of the camshaft thrust plate. Torque the thrust plate retaining capscrews to 9-12 ft./lbs. NOTE: No thrust button is used on Ford engines. (c) Select the desired keyway in the crank gear “0″ (standard), “A” (4ºadvanced at the crank, 2º at the cam), or “R” Place a small amount of clay on the front end of both axles as shown in Figure 3. NOTE: It will be necessary to cut material off rib inside front cover to hold idler gears in place. (b) Install front cover with gasket in place. (c) Remove cover and measure the thickness of the compressed clay. It should be .005″-.030″. Do not tighten cover down until proper clearance has been obtained. Without sufficient clearance, there is risk of cracking the cover when tightened down. (d) If clearance is less than .005, you will need to grind off idler axle as shown to obtain proper clearance. If clearance is greater than .090, replace left side (larger idler side) stud with tapered end axle provided in the kit. Re-install idler assembly and recheck for minimum clearance between block and front cover. 8. With all gears correctly in mesh and timed, tighten the camshaft capscrew to 35 ft./lbs. It would also be a good idea to use Locktite™ or equivalent on the bolt threads prior to final assembly. 9. Lubricate all gears and bearings with engine oil. 10. Re-install the front cover. 11. Re-install all components removed in preparation for step 1

Related Content:

P30 bellcrank assy, 1989 ford escort 1 3 thrust washer end play, 1995 ford 6 cylinder cam gear marks, ford 200 camshaft

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

How to Fix Po446 Code ford escape xls, 555 ford backhoe repair manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, Ford E 450 Cutaway Manual, ford 9 inch repair manual, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, Ford OBD1 Codes and Fixes for Them, how many quarts of transmission fluid does 2012 ford e450 take?

3406E TRUCK ENGINE 2WS Camshaft Gear Removal And Installation Manual

0

Filed Under (More Manuals) by admin on 28-05-2012

download
1. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 2. Remove top bolt (2) from camshaft gear (1) . Install Tooling (A) in place of the bolt. 3. Remove remaining bolts (2) and remove camshaft gear (1) . 4. NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. Remove Tooling (A) . 5. Installation Procedure Required Tools Tool Part Number Part Description Qty A 9U-6896 Guide Bolt 1. Align the hole in the back of camshaft gear (1) with the dowel in the adapter. Install camshaft gear (1) over Tooling (A) . Note: Camshaft timing is critical. The timing mark on the camshaft gear must be aligned with the timing mark on the front cover when the No. 1 piston is at the top center of the compression stroke. Refer to Testing and Adjusting, “Gear Group (Front) – Time”. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 3. Note: If the timing marks are not aligned, remove camshaft gear (1) and rotate the camshaft until the timing marks are aligned. Install bolts (2) . Remove Tooling (A) and install remaining bolt (2) . 4. 5. Check the backlash between the camshaft gear and the adjustable idler gear. The backlash should be 0.216 ± 0.114 mm (0.0085 ± 0.0045 inch). Refer to Testing and Adjusting, “Gear Group (Front) – Time” for the backlash adjustment procedure. 6. End By: Install the front cover. Refer to Disassembly and Assembly, “Front Cover – Install”

Related Content:

volvo s40 cam alignment instructions, 3406e front cover removal, 3406e timing gear backlash, c15 cam gear backlash, Cat C15 rotation, mazda timing marks 1991 mx6

Ford V6 And V8 Timing Set Installation Instructions

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Installation Instructions 1. Clean everything! Make sure that the engine mounting surfaces and your new timing set have been thoroughly cleaned with a good solvent. 2. If you are using a timing set with three keyways, select the appropriate keyway for your camshaft timing specifications. COMP Cams ® recommends the standard timing position for most applications. This position uses the round or “O” timing and keyway marks. Standard Timing Location: This is the same as original O.E.M. setting. Use keyway and crankshaft gear tooth marked “O”. É 4 Degree Advance: Use keyway and crankshaft tooth marked . Note: The or advanced position should not be used without degreeing the camshaft. Many camshafts have the proper advance built in. Advancing the cam will reduce intake valve to piston clearance and increase exhaust piston to valve clearance. É 4 Degree Retard: Use keyway and crankshaft gear tooth marked . Note: The or retarded position should not be used without degreeing the camshaft. Many cams have the proper advance built in. Retarding the cam will reduce exhaust valve to piston clearance and increase intake piston to valve clearance. 3. Install your lower timing gear on the crankshaft making sure that the timing marks are facing out toward you. 4. Now that the lower timing gear has been installed check the timing mark alignment in your engine manual. Rotate the crankshaft using your crankshaft socket until the timing mark on the gear is in the proper position (12 o’clock). For 240-300 6 cyl. see Note 1 before proceeding! 5. If your engine is equipped with a camshaft retaining plate or thrust plate, it should be installed at this time. Note that many Ford thrust plates are marked “back – bottom”. Before final installation check to make sure that the thrust plate is fitted correctly. 351W owners see Note 2 before proceeding! 6. Temporarily install your camshaft timing gear and rotate the camshaft until the timing mark on the camshaft gear is in the proper position per your engine manual instructions (6 o’clock) Ford Timing Set Installation Instructions

2002 Dodge Truck RAM 2500 Symptom Related Diagnostic Procedures/ Installation Manual

0

Filed Under (Dodge Manuals) by admin on 16-02-2012

download
46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING Before road testing, be sure the fluid level and control cable adjustments have been checked and adjusted if necessary. Verify that diagnostic trouble codes have been resolved.Observe engine performance during the road test. A poorly tuned engine will not allow accurate analysis of transmission operation. Operate the transmission in all gear ranges. Check for shift variations and engine flare, which indicates slippage. Note if shifts are harsh, spongy, delayed, early, or if part throttle downshifts are sensitive. Slippage indicated by engine flare, usually means clutch , band or overrunning clutch problems. If the condition is advanced, an overhaul will be necessary to restore normal operation. A slipping clutch or band can often be determined by comparing which internal units are applied in the various gear ranges. The Clutch and Band Application chart provides a basis for analyzing road test results. Note that the rear clutch is applied in all forward ranges (D, 2, 1). The transmission overrunning clutch is applied in first gear (D, 2 and 1 ranges) only. The rear band is applied in 1 and R range only. Note that the overdrive clutch is applied only in fourth gear and the overdrive direct clutch and overrunning clutch are applied in all ranges except fourth gear. For example: If slippage occurs in first gear in D and 2 range but not in 1 range, the transmission overrunning clutch is faulty. Similarly, if slippage occurs in any two forward gears, the rear clutch is slipping. Applying the same method of analysis, note that the front and rear clutches are applied simultaneously only in D range third and fourth gear . If the transmission slips in third gear, either the front clutch or the rear clutch is slipping. If the transmission slips in fourth gear but not in third gear, the overdrive clutch is slipping. By selecting another gear, which does not use these clutches, the slipping unit can be determined. For example, if the transmission also slips in Reverse, the front clutch is slipping. If the transmission does not slip in Reverse, the rear clutch is slipping. If slippage occurs during the 3-4 shift or only in fourth gear , the overdrive clutch is slipping. Similarly, if the direct clutch were to fail, the transmission would lose both reverse gear and overrun braking in 2 position (manual second gear). If the transmission will not shift to fourth gear , the control switch, overdrive solenoid or related wiring may also be the problem cause.

Related Content:

replacing a torque converter clutch solenoid on a kia, torque converter cluch selenoid on 1999 odyssey, cd4e application chart, 47 no forward gears, ax4n clutch and band chart, ford cd4e automatic gear chart, ford cd4e gear chart, How to fix f150 torque converter clutch solenoid, Overdrive Solenoid Symptoms, ranger ac clutch solenoid 2001

2002 Dodge Truck RAM 2500 46RE AUTOMATIC TRANSMISSION DIAGNOSIS AND TESTING – ROAD TESTING

0

Filed Under (Dodge Manuals) by admin on 20-02-2011

download
The Clutch and Band Application chart provides a basis for analyzing road test results. Note that the rear clutch is applied in all forward ranges (D, 2, 1). The transmission overrunning clutch is applied in first gear (D, 2 and 1 ranges) only. The rear band is applied in 1 and R range only. Note that the overdrive clutch is applied only in fourth gear and the overdrive direct clutch and overrunning clutch are applied in all ranges except fourth gear. For example: If slippage occurs in first gear in D and 2 range but not in 1 range, the transmission overrunning clutch is faulty. Similarly, if slippage occurs in any two forward gears, the rear clutch is slipping. Applying the same method of analysis, note that the front and rear clutches are applied simultaneously only in D range third and fourth gear . If the transmission slips in third gear, either the front clutch or the rear clutch is slipping. If the transmission slips in fourth gear but not in third gear, the overdrive clutch is slipping. By selecting another gear, which does not use these clutches, the slipping unit can be determined. For example, if the transmission also slips in Reverse, the front clutch is slipping. If the transmission does not slip in Reverse, the rear clutch is slipping. If slippage occurs during the 3-4 shift or only in fourth gear , the overdrive clutch is slipping. Similarly, if the direct clutch were to fail, the transmission would lose both reverse gear and overrun braking in 2 position (manual second gear). If the transmission will not shift to fourth gear , the control switch, overdrive solenoid or related wiring may also be the problem cause. This process of elimination can be used to identify a slipping unit and check operation. Proper use of the Clutch and Band Application Chart is the key. Although road test analysis will help determine the slipping unit, the actual cause of a malfunction usually cannot be determined until hydraulic and air pressure tests are performed. Practically any condition can be caused by leaking hydraulic circuits or sticking valves.Unless a malfunction is obvious, such as no drive in D range first gear , do not disassemble the transmission. Perform the hydraulic and air pressure tests to help determine the probable cause.

Related Content:

Manual Overdrive Units

Related Content:

how to check the backlash between the camshaft gear and the adjustable idler gear for 3406 e monel, used set of pistons for 2000 nissan altima with2 2, how to fix a shifter in a 2000 chevy malibu, VVTI GEAR POSITION DETERMINED BY CAM SENSOR WAVEFORM, how to fix a broken column shifter on a 2003 toyota sequoia, how to change shift boot hummer h3, how do i replace the rear differential seal in my 2006 kia sorento ex 4wd, Gear shift nob broken on 2000 Chev Malibu, gear selector for 00 rodeo only goes in first and reverse, how to fix a loose metal knob control panel on a window whirlpool room ac