ford 550 backhoe injector pump timing

You search PDF repair manual about ford 550 backhoe injector pump timing, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford 550 backhoe injector pump timing Direct Download speed 5432 Kb/s

  ford 550 backhoe injector pump timing Full Version speed 8172 Kb/s



1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, rager injection pump parts manual, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, cav injector pump governor spring, how to change water pump on a dewoo, isuzu dmax fuel pump, 89 dodge dakota fuel pump diagram, 2002 isx cummins manual pump installation, digram for cav fuel injectorpump for 2810 ford tractor

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture, NTC350 drive gear remova

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

1994 Mitsubishi Expo LRV TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 30-04-2012

download
Removal 1. Remove radiator shroud, cooling fan and pulley. Remove all drive belts and crankshaft pulleys. Remove upper timing belt covers and gaskets. Note bolt length and location. 2. Remove crankshaft sprocket bolt and washer. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with mark on cylinder head. See Fig. 5 . 3. Loosen timing belt tensioner adjustment bolt, and move tensioner toward water pump. Tighten bolt to secure tensioner. Remove front timing belt and tensioner. DO NOT rotate crankshaft after timing belt has been removed. 4. Remove camshaft sprocket (if necessary). Remove oil pump sprocket access plug from cylinder block. See Fig. 4 . Insert a .31″ (8.0 mm) diameter Phillips screwdriver to block left silent shaft. 5. Remove oil pump sprocket nut, and remove sprocket. Remove front crankshaft sprocket and flange. Note direction and order of installation for reassembly reference. 6. Remove rear timing belt tensioner assembly. Remove rear timing belt. Remove right silent shaft sprocket with spacer (if necessary). Remove rear crankshaft sprocket with key Installation 1. Install rear crankshaft sprocket and flange. Install right silent shaft sprocket and spacer. Spacer should be installed with chamfered end into oil seal. Align timing marks. See Fig. 5 . 2. Install rear tensioner. Hold tensioner tightly against belt while tightening bolts. Ensure deflection is .20- .28″ (5.0-7.1 mm). See Fig. 6 . Install camshaft sprocket. Tighten camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS . 3. Install front timing belt tensioner, tension spring and spacer. Ensure spring is properly engaged against water pump case. Rotate tensioner toward water pump, and temporarily tighten bolts. Ensure timing marks are aligned. See Fig. 5 . Install timing belt on crankshaft. 4. Apply pressure on tension side of timing belt while installing belt (in order) on crankshaft, oil pump and camshaft sprockets. Loosen tensioner to apply spring pressure to timing belt. 5. To apply tension to belt, rotate crankshaft clockwise until camshaft sprocket timing mark is offset by 2 teeth. Tighten tensioner bolt. Tighten tensioner spacer nut

Related Content:

04 volvo s60 2 5t how to align cam shafts to cam sprockets, adjusting cam sprockets, chrysler sprocket removal tool, ej25d enigine TORQUE, what are torque values for 2 2ecotec cam sprokets

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

wire diagram on a 2002 grand prix headlight, 1998 jimmy fuel pump install, 03 ford windstar fuel pump wiring, vcm ground wire, pontiac grand am fuel pump wireing harness replacement instructions, proper connection for horn relay 1968 chevelle, 2005 tundra speed pulse signal wire location, fan cable for 1998 dodge caravan, location of vent valve solenoid on 2010 ford ranger, 86 corvette wiring schematics

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 98 eclipse rs service manual, 2002 diamante timing belt, 2002 jetta crank mark, should the timing arrow on a zx2 move when belt is pressed, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, how to adjust belt on 2001 kia optima, kia rio 5 2007 timming belt, 3126 timing pin hole

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, where is the washer relay located in a 2009 chevy impala, where is the relay switch for liftgate in 2005 esclade, g5 sunroof relay, 1993 corvette power seat and power window shorting out breaker, 99 eldorado fuel pump relay test, l wiper delay control modual for85 ford thunderbird

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Related Content:

free download Service Manual for a 1992 Toyota Truck, Toyota 5K ignition, _1987_Nissan_pickup_v6 destributer timing marks

Ford V6 And V8 Timing Set Installation Instructions

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Installation Instructions 1. Clean everything! Make sure that the engine mounting surfaces and your new timing set have been thoroughly cleaned with a good solvent. 2. If you are using a timing set with three keyways, select the appropriate keyway for your camshaft timing specifications. COMP Cams ® recommends the standard timing position for most applications. This position uses the round or “O” timing and keyway marks. Standard Timing Location: This is the same as original O.E.M. setting. Use keyway and crankshaft gear tooth marked “O”. É 4 Degree Advance: Use keyway and crankshaft tooth marked . Note: The or advanced position should not be used without degreeing the camshaft. Many camshafts have the proper advance built in. Advancing the cam will reduce intake valve to piston clearance and increase exhaust piston to valve clearance. É 4 Degree Retard: Use keyway and crankshaft gear tooth marked . Note: The or retarded position should not be used without degreeing the camshaft. Many cams have the proper advance built in. Retarding the cam will reduce exhaust valve to piston clearance and increase intake piston to valve clearance. 3. Install your lower timing gear on the crankshaft making sure that the timing marks are facing out toward you. 4. Now that the lower timing gear has been installed check the timing mark alignment in your engine manual. Rotate the crankshaft using your crankshaft socket until the timing mark on the gear is in the proper position (12 o’clock). For 240-300 6 cyl. see Note 1 before proceeding! 5. If your engine is equipped with a camshaft retaining plate or thrust plate, it should be installed at this time. Note that many Ford thrust plates are marked “back – bottom”. Before final installation check to make sure that the thrust plate is fitted correctly. 351W owners see Note 2 before proceeding! 6. Temporarily install your camshaft timing gear and rotate the camshaft until the timing mark on the camshaft gear is in the proper position per your engine manual instructions (6 o’clock) Ford Timing Set Installation Instructions

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, rager injection pump parts manual, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, cav injector pump governor spring, how to change water pump on a dewoo, isuzu dmax fuel pump, 89 dodge dakota fuel pump diagram, 2002 isx cummins manual pump installation, digram for cav fuel injectorpump for 2810 ford tractor