Skip to content

ford door reinforcement

You search PDF repair manual about ford door reinforcement, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

1991-1994 FORD TEMPO VEHICLE WIRING

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.

1998 Ford F 150/250 Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. Remove the passenger air bag. For additional information, refer to Section 501-20B . 3. Remove the driver air bag. For additional information, refer to Section 501-20B . 4. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Carefully pry to release the (A) clips and remove the (B) steering column opening cover. 5. Position the electrical connector aside. * Release the push clip from the lower instrument panel steering column cover (044F08). 6. Pull to release the three (A) clips and remove the (B) fuse door. 7. Position the hood latch release handle aside. 1. Remove the screws. 2. Position the hood latch release handle aside. 8. Position the parking brake release handle aside. 1. Remove the screws. 2. Position the parking brake release handle aside. 9. If equipped, remove the instrument panel floor duct panel. * Remove the two push clips and release the expander clip. 10. Remove the lower instrument panel steering column cover (04459). 1. Remove the bolts. 2. Remove the lower instrument panel steering column cover. 11. Remove the LH and RH scuff plates. 12. Remove the LH and RH cowl side trim panels. 13. Disconnect the brake pedal position (BPP) switch electrical connector. 14. Remove the (A) radio ground and the (B) GEM/CTM ground bolts. 15. Disconnect the LH instrument panel main harness connectors. 16. Remove the bulkhead wiring harness electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 17. Remove the bulkhead electrical connector from the dash panel. 1. Release the six locking tabs. 2. Remove the bulkhead connector from the dash panel. 18. Disconnect the air bag diagnostic monitor electrical connectors. 19. Disconnect the inertia fuel shutoff switch electrical connector. 20. Remove the RH ground bolts. 21. Disconnect the RH instrument panel main harness connectors. 22. Disconnect the electronic blend door actuator electrical connector. 23. Disconnect the climate control head vacuum harness connector. 24. Remove the instrument panel steering column opening cover reinforcement (04502). 1. Remove the nuts. 2. Remove the instrument panel steering column opening cover reinforcement. 25. Disconnect the air bag sliding contact electrical connectors and the anti-theft sensor electrical connector.