ford escape cylinder head remove replace

You search PDF repair manual about ford escape cylinder head remove replace, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford escape cylinder head remove replace Direct Download speed 5432 Kb/s

  ford escape cylinder head remove replace Full Version speed 8172 Kb/s



2009 Ford Escape 3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/ THUMP NOISE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 25-01-2012

download
3.0L INTERMITTENT CYLINDER HEAD CAMSHAFT KNOCK/THUMP NOISE This article supersedes TSB 09-11-6 to update the b. Isolate noise to LH – Listen to the cylinders Service Procedure and Part List. 4 and 6 valve cover fasteners (number 6 is by the coolant pump). There will be a ISSUE significant difference in transmitted noise Some 2009 Escape and Mariner vehicles, equipped between the cylinder 4 and 6 fasteners with 3.0L engine, may exhibit an intermittent when noise is present. Noise from LH – go knocking or thumping type noise from the cylinder to Step 4. head. After engine temperature reaches 210-220 °F NOTE (99-104 °C), the noise is typically heard from the THE RH AND LH NOISES HAVE DIFFERENT rear of the engine as the vehicle comes to a stop. CAUSES. FOLLOW ALL STEPS CAREFULLY FOR An example would be coming to a stop at the end PROPER DIAGNOSIS AND REPAIR. of a highway exit ramp. Noise will continue 45-60 seconds and then diminish. Noise will occur again 3. Replace the RH cylinder head per Workshop once engine reaches 210-220 °F (99-104 °C) and Manual (WSM), Section 303-01B. vehicle comes to another stop. a. Verify repair by repeating Step 2. If noise is ACTION still present then proceed with normal Follow the Service Procedure steps to correct the engine NVH diagnostics per WSM, Section condition. 100-04. SERVICE PROCEDURE 4. Remove LH valve cover. Refer to WSM, Section 303-01. 1. Is noise a 45-60 second knock/thump from a hot engine as the vehicle comes to a stop? a. Rotate the engine clockwise until cylinder number 6 exhaust cam lobes are pointing a. Yes – Go to Step 2. up and valves are fully closed. Exhaust camshaft needs to be left in this position for b. No – Stop as this procedure does not apply. all bearing caps in Step 4b. (Figure 1) Proceed with normal Workshop Manual (WSM), Section 100-04 diagnostics. 2. Using Chassis Ears, isolate the noise to Right Hand (RH) (Bank 1) or Left Hand (LH) (Bank 2) cylinder head. Noise is typically heard as 45-60 second knock/thump as the vehicle comes to a stop after engine reaches 210-220 °F (99-104 °C). a. Isolate noise to RH – Listen to the cylinder head by the variable camshaft timing (VCT) solenoid connectors. There will also be a vibration felt at the VCT solenoid connector when noise is present. Noise from RH – go to Step 3.

Related Content:

02 kia rio 1 5 will idle no accelaration, 2013 f-150 click noise at stop and start, causes of ford escape 2001 engine vibration, 2005 tundra tailgate noisey, ticking noise and misfire 4 8 litre gmc, chevy silverado catalytic converter 2004 v6 knocking tapping noise, Ford Escape motor mount removal and installation how to, GMC noise when brakes applied or released, how do i change the VCT solenoids on 2009 ford escape, installing engine in a 2008 ford escape

Related Content:

02 kia rio 1 5 will idle no accelaration, 2013 f-150 click noise at stop and start, causes of ford escape 2001 engine vibration, 2005 tundra tailgate noisey, ticking noise and misfire 4 8 litre gmc, chevy silverado catalytic converter 2004 v6 knocking tapping noise, Ford Escape motor mount removal and installation how to, GMC noise when brakes applied or released, how do i change the VCT solenoids on 2009 ford escape, installing engine in a 2008 ford escape