ford escape evaporative emmission dust collector

You search PDF repair manual about ford escape evaporative emmission dust collector, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford escape evaporative emmission dust collector Direct Download speed 5432 Kb/s

  ford escape evaporative emmission dust collector Full Version speed 8172 Kb/s



2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, where is the vct solenoid located on a 2009 ford escape, 1988 ford f150 302 where is Diagostic Link Connector located, ford 9 inch repair manual, how many quarts of transmission fluid does 2012 ford e450 take?, free Ford Motorhome Chassis F53 Manual pdf

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

K40016 ADD-A-LEAF SPRING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 19-04-2012

download
CHEVY 1982-98 S Series all 2WD/4WD 1972-82 LUV PU 2 WD DODGE 1994-99 Ram 1500 2WD 1994-00 Ram 1500 4WD FORD 1990-96 F 150 std or ext cab 2WD 1982-89 F 150 std or ext cab 2WD 1983-1996 Ford Bronco II 4WD 1983-1996 Ford Bronco II 2WD 1983-1997 Ford Ranger 2WD/4WD 1990-00 Ford Ranger 2WD 1983-97 Ford Explorer 2WD/4WD 1972-84 Ford Courier 2WD K40016 ADD-A-LEAF SPRING KIT JEEP 1984-01 Jeep Cherokee 1974-86 CJ-5/CJ-7/CJ-8 4WD 1967-73 Jeepster/C101/C101 w multileaf Jeep Wrangler 1987-96 Front and Rear LAND ROVER 1959-1981 All 4wd MITSUBISHI 1986-91 Montero 1982-84 PU 2WD/4WD NISSAN 1968-1997 PU/Pathfinder 2WD/4WD TOYOTA 1963-98 Toyota PU/4 Runner with 2.5″ rear springs The K40016 Add-A-Leaf Spring Kit retrofits onto the following vehicles: The kit consists of two each 28″ Leaf Springs and two sets of two each longer bolts and nuts of different diameters. The same diameter bolt currently on the vehicle should be used and the other set discarded. • PLEASE READ ALL INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION • You must use 2-large “C-clamps” or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed. • The new leaf spring will be placed in the existing spring assembly in a progressive pyramid shape. Example – if your number 1 Spring is 32″ long and the next one is 25″ long, the new Add-A-Leaf Spring should be place between them. • Some vehicles will have a flat helper stack. SEE ILLUSTRATION – DO NOT INSTALL THE NEW ADD-A-LEAF SPRING IN OR BELOW THE HELPER SPRIN(S). Helper spring assembly. Do not install Add-A-Leaf in or below this assembly Lowest allowable position for Add-A-Leaf

Related Content:

1969 ford truck ranger 390 overheating did not start till change water pump, fluid spec for 2004 ford ranger, f53 96 manual, 83 ranger wiring diagram, 1996 Ford RV specifications, 1996 Ford Explorer Repair Manual, 1996 ford explorer manual, 1996 f53 manifold exhaust repair, 1986 555b ford backhoe injector pump, ford ranger 2 3 engine diagram

4.6L Mustang Bassani Mid Length Headers INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 05-12-2011

download
INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Safely raise & support vehicle to a comfortable working height. (One jack stand at each corner of vehicle.) 3. Spray attaching hardware and base of o2 sensors with WD40 or similar Lubricant. Remove 02 sensors from stock system. (Be careful not to damage or contaminate sensor). Stock gasket will be re-used upon assembly. 4. Remove both connector tubes between stock exhaust manifold and Bassani Modular X pipe. It may be necessary to loosen downstream clamps on the Bassani Modular X pipe. 5. Loosen EGR fitting on drivers side exhaust manifold. It will be necessary to remove nuts from the motor mounts at the K member to jack engine up. Motor mount heat shields have to be removed. 6. Loosen & remove both exhaust manifolds. 2 valve, stock manifold gaskets, depending on condition, may be re-used . Remove studs from both sides. Use supplied, and/or stock hardware. See note following #10. 7. Label wiring on starter and remove it. (Will be necessary for header installation) 8. You may also need to remove oil filter to ease installation and tightening on drivers’ side. 9. IMPORTANT! It will be necessary to unbolt steering shaft from rack. With a marker draw a straight line on shaft down to rack to index them both. Do not move front wheels or steering wheel. 10. It will be necessary to lift engine up enough to slide header tubes in and have access to install supplied header bolts. After loosening motor mount bolts, lifting engine (using a wooden block under oil pan) and removing motor mounts, one side at a time only, will ease installation. Removal of motor mounts is not mandatory. **Anti seize must be applied to all threads (header bolts and studs). It may be necessary to use a combination of header bolts and stock studs & nuts on certain tubes due to clearance between the tube and hardware. ie; stud nut or header bolt. The use of either is the installers preference. 11. Start on passenger side, with tube #1R. Push as far forward as possible to allow clearance for #2R. Once #2R is in position, install gaskets, and header bolts. When this is completed commence installation of #3R and #4R tubes following previous procedure. Leave bolts loose, DO NOT TIGHTEN UNTIL COLLECTOR IS INSTALLED. 12. When Collector R is ready for right side, place Bassani anti seize jet lube , on slip connectors to ease installation. When collector lines up with tab on header tube, fasten them together and tighten all header tubes. 13. When all hardware is properly tightened, lower engine, re-install motor mount hardware, starter and O2 sensors in collector. The use of Bassani anti seize Jet Lube is recommended on O2 sensor threads. Do not to contaminate O2 sensor bulb with lube. 14. Proceed to drivers’ side. Install #1L with gasket installed. Install supplied fasteners with Bassani anti seize jet lube on the threads. DO NOT TIGHTEN ALL THE WAY, leave semi loose. Install tube #3L, then #2L. You will need to experiment with pipes #2L and #3L. #2L will slip between #3L and #1L. Now install #4L, fasten and screw air fitting to tube #4L. Install Collector L . When collector tab lines up with header tab, tighten all hardware, and bolt on EGR, and any smog fittings. Lower engine and re-install motor mount hardware. Reconnect steering shaft using loctite 271 thread locker on bolt.

Related Content:

2002 chevy s10 exhaust flange seal, ebay ford 555 backhoe cheap service manual, replacing choke heater tube in 57 chevy exaust manifold

FORD, MERCURY, LINCOLN WHITE FLAKES COMING FROM A/ C VENTS SERVICE PROCEDURE

0

Filed Under (More Manuals) by admin on 25-01-2012

download
FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT. WARNING Clean A/C Ducts: MAY CAUSE EYE AND RESPIRATORY TRACT 1. Remove floor duct trim. IRRITATION. PROLONGED REPEATED EXPOSURE MAY CAUSE BONE DAMAGE 2. Using masking tape, connect one end of the (FLUOROSIS) AND HARM TO THE vacuum cleaner hose to the floor duct on driver RESPIRATORY SYSTEM (BASED ON ANIMAL side. DATA). • Avoid inhaling dust. 3. Tape closed all the other floor duct openings. • Avoid contact with eyes. 4. Obtain about two feet (61 cm) of rubber • Store away from acids. vacuum line large enough to fit the end of a small shop air blowgun. Secure the hose to the • Wash thoroughly after handling. end of the blowgun using a worm clamp. • Avoid release to the environment. 5. Close all instrument panel registers. NOTE THE USE OF DUST PROOF GOGGLES, 6. Set temperature setting to full cold. CHEMICAL RESISTANT GLOVES (PVC) AND 7. Place mode in floor / panel. DUST MASK IS RECOMMENDED. 8. Turn on vacuum cleaner

Related Content:

2008 focus door panel removal, 1994 grand marquis service manual, pdf on fixing ford town car, u2023 2005 mercury mariner, 1994 mercury grand marquis ls manual, removing a 2013 edge door panel, remove engine from 2007 focus, w584a lincoln ls, lincoln ls part number PA66-GF30, how to remove drivers door panel 2012 edge

2008 Ford F-250/350/450 6.4L Powerstroke diesel aft-filter system Installation Manual

0

Filed Under (Ford Manuals) by admin on 08-12-2011

download
Installation instructions: 1.) Raise and support vehicle. 2.) Lubricate all factory rubber hangers and pipe slip-connectors with penetrating oil. 3.) Loosen clamp, attaching inlet of stock muffler to inlet pipe. 4.) Remove muffler/tailpipe assembly from inlet pipe and rubber hangers; remove from vehicle. Removal of muffler/tailpipe can be made easier by first cutting the tailpipe from the muffler with a reciprocating saw. 5.) Remove hanger rod on inlet pipe from rubber frame hanger. 6.) Loosen clamp attaching inlet pipe to outlet of converter and remove pipe from vehicle. 7.) Place supplied 3.5? clamp with hole over small end of supplied adapter and install onto outlet of converter. Engage slot in adapter with index bump on converter outlet and place hole in clamp over bump. Tighten clamp fully. 8.) Place one supplied 4? clamp over inlet pipe slip-connector and install pipe onto adapter. Insert hanger rod on pipe into corresponding rubber hanger on frame. 9.) Rotate inlet pipe as needed to orient end of hanger rod, which is inserted into rubber hanger, in a horizontal position and tighten clamp at slip-connector fully 10.) Place one supplied 4? clamp over muffler inlet and install muffler onto inlet pipe. 11.) Place one supplied 4? clamp over inlet of tailpipe section “A” and install pipe onto muffler and into corresponding factory rubber hangers just above muffler. 12.) Place one supplied 4? clamp over inlet of tailpipe section “B” and install pipe into rear-most rubber frame hanger and onto outlet of tailpipe section “A”. 13.) Place remaining 4? clamp over tip inlet and install tip onto outlet of tailpipe section “B”. 14.) Align all components for desired fit and tighten all clamps fully

Related Content:

6 0work shop manual pdf, 1957 ford o matic transmission torque convertor torque spec, 1995 Ford Mustang conv owners manual, 2003 windstar exhaust hanger rubber, 99 ford windstar rubber exhaust support, 99 ford windstar tail pipe rubber hanger, Muffler hanging silencer hanger exhaust hanger auto shock absorber, replacing the exhaust grommet 2000 windstar

Ford Mustang GT Stainless Steel longtube headers Installation instructions

0

Filed Under (Uncategorized) by admin on 06-12-2011

download
Installation instructions: 1.) Open hood and disconnect negative battery cable from battery. 2.) Remove air box assembly from driver side of engine compartment to provide needed space to install header tubes. 3.) Raise and support vehicle on a suitable lift as per lift instructions. 4.) Disconnect all four oxygen sensor electrical harness connectors and remove sensors from exhaust system with a 7/8 wrench. Mark each sensor so as to enable reinstallation in the same location. 5.) Remove all fasteners and clamps attaching stock H-pipe to exhaust manifolds and over-axle pipes. Remove H-pipe from vehicle. 6.) Remove all fasteners (nuts and studs) attaching exhaust manifolds to cylinder heads and remove manifolds from engine. 7.) Loosely assemble passenger side header on the ground or bench top to obtain a mental picture of the relationship of the header tubes to each other and the collector. 8.) Disassemble header assembly and load passenger side header tubes into the car from bottom of engine. Do not bolt any tube to cylinder head until you are able to get all four into approximate position. Exercising patience during this step will help to prevent scratching the header coating. 9.) Attach passenger side header tubes to cylinder head using stock gaskets and supplied 8mm header bolts but do not fully tighten until last step. Be sure to use supplied anti-seize compound on bolt threads. 10.) Apply a thin coat of Permatex Ultra Copper high-temp silicone to inside of collector slip joints æ of the way to the bottom and install collector over ends of header tubes with oxygen sensor bung facing driveshaft. Use your finger to evenly spread sealant. 11.) Install supplied 1/4″ hardware into tabs on collector and corresponding header tubes. Do not tighten fasteners until last step of installation. 12.) Proceed to driver side. 13.) Loosely pre-assembly header assembly as before to obtain a mental picture of tube positions relative to each other then disassemble. 14.) Feed the number 2 header tube between steering column and frame and into its approximate installed position. You will need the assistance of a pry bar to accomplish this as the flange is slightly too large to pass through this point without doing so. 15.) Working through the top of engine compartment, install the number 1 header tube into position with the number two header tube. Now attach both header tubes to cylinder head with stock gaskets and supplied fasteners but do not fully tighten until last step. 16.) Install number 3 and number 4 tubes into position from underneath vehicle and attach to cylinder head with supplied fasteners; do not fully tighten until last step. 17.) Apply a thin coat of Permatex Ultra Copper high-temp silicone to inside of collector slip joints æ of the way to the bottom and install collector over ends of header tubes with oxygen sensor bung facing driveshaft. Use your finger to evenly spread sealant. 18.) Install pre-catalyst oxygen sensors into header collectors and connect to electrical harness with supplied harness extensions. 19.) If you are installing headers with a Bassani “X” style crossover pipe, install the crossover pipe as per the included instructions. The two oxygen sensor bungs included with these headers can to be used to install these headers with any custom fabricated mid-pipe assembly if you choose to not install a direct fit, Bassani off-road or catalyzed “X” style crossover pipe. 20.) Connect rear oxygen sensors installed in Bassani crossover pipe to electrical harness with supplied extensions. It will be required to trim off index lugs from male side of O2 sensor connectors to enable insertion into mating female connector of extension. 21.) Tighten all fasteners on left and right header assemblies. 22.) Reinstall air filter housing assembly and reconnect negative battery cable

2006 Ford F-SUPER DUTY Class A Motorhome Chassis INCOMPLETE VEHICLE MANUAL

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
Certain exhaust system components, including exhaust heat shielding systems, have been installed on some vehicles in our assembly plants in an effort to provide protection against engine compartment and exhaust system temperatures. Subsequent aftermarket installers/manufacturers are responsible for providing thermal protection (e.g. underbody heat shields) for any structure and/or equipment added to the vehicle and should not remove any components or exhaust heat shielding installed on the vehicle by Ford Motor Company. All exposed interior sheet metal of closed structures (e.g. fl oor pan of cab and/or secondary structure, tool boxes, etc.) should be covered with an insulating material capable of protecting vehicle occupants and contents from temperatures potentially up to 700°F. OZONE DEPLETING SUBSTANCE (ODS) OZONE DEPLETING SUBSTANCE (ODS) The Clean Air Act of 1990, Section 611 requires any product (i.e., completed vehicle) containing or manufactured with any Class I Ozone Depleting Substance on, or after May 15,1993 must be identifi ed with a “clearly and conspicuously attached label.” Ford Motor Company has eliminated Class I ODS from its manufacturing processes. All 2006 Ford Truck incomplete vehicles will not have Class I ODS content. Manufacturers, including subsequent stage manufacturers, are required to label their products if the product, including any component (whether manufactured by that manufacturer or not), contains a Class I ODS or if the manufacturer used a Class I ODS in the manufacturing of the product. In the case where Ford Motor Company provides a label saying the incomplete vehicle contains a Class I ODS that information must be placed on the product warning label. (See EPA regulation on wording, placement, size, and combining labels.) In Canada consult the appropriate Provincial or Territorial Ministry of Environment. EMISSION CONTROL INFORMATION LABEL To meet United States Environmental Protection Agency regulations, the Important Vehicle Information (tune-up and fuel tank capacity) labels must be affi xed in a location that is readily visible after installation and in such a manner that it cannot be removed without destroying or defacing the label. The label shall not be affi xed to any equipment that is easily detached from the vehicle. When emission control labels are supplied but not attached to the vehicle (i.e., tune-up label or fuel tank label), they must be permanently mounted in a readily visible location to meet the preceding requirements. In addition, whether the label is already affi xed or to be affi xed, no components shall be installed which visibly obscure the label in any way that fails to satisfy the visibility requirements described in the California Emission Control Label Specifications. For Canadian requirements consult Section 1100 8 (1) (d) (i), (ii), & (iii). CALIFORNIA FUEL VAPOR RECOVERY California regulations require that the vehicle fuel systems be designed to accommodate a vapor recovery fueling nozzle including unobstructed access to the fi ll pipe. Fuel fi ller pipes installed per the Figure B on page 15 will comply with the “Specifi cations For Fill Pipes and Openings of Motor Vehicle Fuel Tanks” referenced in Title 13 California Administrative Code provided no part of the aftermarket body, as installed, intrudes within a 254mm [10 in] radius cylinder which has its axis parallel to the ground at point “Z” and extends outward from the Ford Motor Company supplied fuel pipe housing component. The fuel pipe housing component is shown on the referenced fi gures and is attached to the aftermarket body via 4.76 mm [.188 in.] diameter rivets. Fuel fi ller pipes installed using the alternative bracket shown in Figure B, will comply with the above California vapor recovery regulations provided the aftermarket body does not interfere with the access zone as defi ned by the California Air Resources Board, and the areas adjacent to this opening cannot foreseeably damage the nozzle bellows or face plate of nozzles during insertion, latching, disposing or removal

Related Content:

ford class c chassis cruise control operation manual, 1990 Ford Class B motor home how to manual, 1996 ford e super duty motorhome specifications, 1998 F-Series Super Duty Class A Motorhome Chassis Manual, 1999 Ford F-250 Truck OBD II Powertrain Control & Emissions Diagnosis Manual, 2006 Ford F-53 motorhome chassis wheel bearing part numbers, how to replace a blend door actuator in a 2002 fourwinds class c motorhome, u2023 code ford explorer

2001 Ford Truck F 150 Engine – Spark Plug Hole Thread Repair Procedure

0

Filed Under (Ford Manuals) by admin on 26-04-2012

download
SERVICE PROCEDURE Ford Motor Company now authorizes LOCK-N-STITCH aluminum insert and tool kit as a proper repair procedure. Follow the procedure included in the tool kit for using the tools and inserts. Tool kits and inserts can be ordered from Rotunda by calling 1-800-Rotunda (768- 8632). Choose option two (2), part number 302-00001. NOTE FORD MOTOR COMPANY HAS DETERMINED THAT REPAIRS MADE WITH THESE ALUMINUM INSERTS AND LOCK-N-STITCH TOOLS DO NOT AFFECT THE HEAT TRANSFER FUNCTION BETWEEN THE SPARK PLUG AND THE CYLINDER HEAD. NOTE THIS PROCEDURE IS NOT AUTHORIZED AS A FORD WARRANTY REPAIR. FOR VEHICLES WITHIN WARRANTY, REPLACEMENT OF THE CYLINDER HEAD IS RECOMMENDED. NOTE THIS IS THE ONLY FORD AUTHORIZED PROCEDURE FOR SPARK PLUG THREAD REPAIRS. NOTE THIS PROCEDURE IS AUTHORIZED FOR ESP REPAIRS AND RETAIL REPAIRS. WARRANTY STATUS: Information Only – Not Warrantable

Related Content:

2001 ford taurus repair manual, 2001 Ford Excursion Manual, ford focus 2001 repair manual, ford focus 2001 manual free, F53 King pin specs, cost to replace cooling sydtem taurus, 2010 ford f150 sunroof parts, 2010 ford f 150 lariat sunroof repair, 2001 ford sport trac rear window wont go up, 2001 Ford Ranger EdgeV6 owners manuel

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

0

Filed Under (Ford Manuals) by admin on 10-07-2012

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.

Related Content:

2002 ford ranger cooling system diagram, WSS-M97B44-D and d2 different, m440 cooling system pdf, cooling system diagram for a 1999 ford expedition, cooling system in 2012 mazda 6, diagram of coolant system of a Ford 2008 Expedition, diagram of cooling system for a 2005 ford explorer, radkitplus1, FREE 2002 LINCOLN LS COOLING SYSTEM DIAGRAM, isuzu 3 2l cooling system diagram

Related Content:

555 ford backhoe repair manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, where is the vct solenoid located on a 2009 ford escape, 1988 ford f150 302 where is Diagostic Link Connector located, ford 9 inch repair manual, how many quarts of transmission fluid does 2012 ford e450 take?, free Ford Motorhome Chassis F53 Manual pdf