Skip to content

ford flat rate

You search PDF repair manual about ford flat rate, if there are search results will appear below. If search results do not exist, please search by others keyword.

Ford SVT Contour/ Mercury 2.5L V-6 Cougar (5 Speed Manual Transmission Only) Supercharger System Installation Manual

download
1998-2000 FORD SVT CONTOUR/ MERCURY 2.5L V-6 COUGAR Installation Instructions For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change spark plugs at least every 20,000 miles and spark plug wires at least every 50,000 miles. TOOL & SUPPLY REQUIREMENTS: •Factory Repair Manual •3/8″ Socket and Drive Set: SAE & Metric •1/2″ Socket and Drive Set: SAE & Metric •3/8″ NPT Tap and Handle •Adjustable Wrench •Open End Wrenches: 3/8″, 7/16″, 1/2″, 9/16″ •Center Punch •Ford Springlock 3/8″ Fuel Fitting Disconnect Tool •5 Quarts SH/CF Rated Quality Engine Oil •Oil Filter and Wrench •Flat #2 Screwdriver •Phillips #2 Screwdriver •Heavy Grease •Silicone Sealer •Drill Motor •1/8″, 3/16″, 27/64″ Drill Bits •9/16″ Rota Broach Tool (also available from Vortech) •Molylube •Wire Strippers and Crimpers •Utility Knife If your vehicle has in excess of 10,000 miles since its last spark plug change, then you will also need: •Spark Plug Socket •NEW Spark Plugs

FORD 4-PANEL With New Automatic Latch System Truck WITH Factory Tailgate Lock CLASS 3 Installation Manual

download
1) Clean rail surfaces really well with denatured alcohol and make sure they are dry. 2) Press Gasket down firmly the entire length of the gasket 1) Use thin foam double stick tape to hold the clamped hardware in place on inside side rails. The reason we suggest you use this foam is that it is just an extra added protection to keep your clamped hardware from shifting on the sometimes slick surface of some sprayed-in bedliners. • ALL HARDWARE PROVIDED: Stainless steel nuts (18) Part # 9723 or 9723-A – Low Profile Cast aluminum “C” Clamps (16 of them) The only difference with 9723 and 9723-A is that A is a little deeper “C” clamp which is required on some trucks because of the way the inside rail is made. These cast aluminum “C” clamps uninstalled are about the size of a 1 dollar coin and about ¾ inch thick. Part # 9724-T : Latch Installation Tape – (4 pcs.) Part # 9724 – Latch Catch Bracket (4) – These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. Part # 9731 – Center Latch Catches (2) Part # 9736 – D Shaped Seals (2) – Described Above Part # 9714 or 9758 – Stainless Steel Screws (18) (Depending on “C” clamps required above) Part # ST-114 – Keyhole Bracket (2) (Mounted at the Hinge closest to the cab of the truck on the inside of the side rail of the truck at that hinge point). Part # 9727 – Box Seal (2) – Described above INSTALLATION OVERVIEW: 1) Measure and make your marks for your masking tape to put your gaskets on each side. 2) Put down masking tape the entire length of the truck 3) Follow masking tape and install peel and stick gaskets (don’t trim in the rear just yet). 4) Place cover onto truck (you will use the measurements provided to make sure the cover is located exactly in the right position 5) Install Keyhole Bracket (holds the 3rd Leg Hinge) Explanation of 3rd Leg Hinge : • 3rd Leg hinge is a flap of metal that is integrated into the hinge • This flap is on the first hinge right behind the cab of the truck • When you mount the cover, this flap hangs straight down, and slides right into the keyhole bracket 6) Install two “C” Clamps to each Keyhole bracket to secure to the truck 7) Install your stainless steel bolt with lock nut that secures the 3rd Leg Hinge (the flap) into the keyhole bracket on each side. That is “your” permanent point of attachment. (THESE ARE THE SAME TWO BOLTS THAT YOU REMOVE TO TAKE OFF THE COVER) *Remember, the cover is now “installed” and cannot slide around – so you MOUNT ALL THE HARDWARE TO FIT THE COVER from here on out 8) Attach center latch catch on inside of side rails using “C” Clamps. *Center Latch Catch: holds center hinge and the 2 panels in the middle down when the cover is closed. When you close the last panel flat onto the tailgate, a stainless steel “button” along each side of the cover is depressed between the 2 panels at the hinge. When this button is squeezed, it actually pushes a stainless steel latch towards the front of the truck catching the center latch on each side rail. 9) Attach Rear Latch Catch Brackets* using “C” Clamps * These are angled pieces of metal that give your cover’s latches something to “latch to” and are installed with “C” clamps. 10) Install Front Latch Catch Brackets using “C” clamps 11) THIS STEP IS ONLY FOR THE Ford F250/F350 SuperDuty Installations ONLY: The outer seal that comes with your cover and is attached on this rail is called a “Side Box Seal” Because the plastic Ford rails on the SuperDuty are ridged/grooved a little deeper and wider than those on the other Ford trucks, a set of small matte black screws are used in addition to the adhesive on the seal to ensure a snug fit. These screws only slightly penetrate the plastic side rail cover and do not come in contact with the underlying metal side rail

2003-2005 FORD Excursion 6.0L TURBOCHARGER CARBON DEPOSIT DIAGNOSTICS AND SERVICE MANUAL

download
For F-Super Duty, Excursions, and E-Series Once each of the tests are complete, use the IDS vehicles built on or after 9/30/2003, install the VPS help icon on the right side of the screen in each tool 418-626 along with IDS/VMM. The 418-626 test to help analyze the results. If the turbo fails was shipped in kit TKIT-2007VP-F and and leads to turbocharger replacement, continue TKIT-2007TV-F. Dealers should have received one with the Turbocharging Inspection Procedure to or the other of these two kits. check for internal turbocharger oil leakage and to determine if the turbocharger can be repaired with a To Install VPS CHRA replacement, or if it can be cleaned, instead of replacing the entire turbocharger. 1. Remove the threaded pipe plug from center housing of turbo. If the turbocharger passes the turbo tests, do not continue with this TSB. Follow the online KA pin 2. Remove the oil supply flange bolt closest to the point test found on the Professional Technician turbo label. Society (PTS) website and continue air 3. Drop in the VPS and secure with provided management diagnosis without replacing the clamp flat side up. turbocharger. 4. Torque the oil supply line bolt 7 lb-ft (10 N•m). NOTE VEHICLE PERFORMANCE ISSUES RELATED TO 5. The gasket is reusable and need only be FUEL QUALITY, MAINTENANCE AND replaced if an oil leak is present after final AFTERMARKET MODIFICATIONS ARE NOT assembly. COVERED BY FORD MOTOR COMPANY WARRANTY. To run test, start new session in IDS with VPS/VMM connected to the vehicle. Then select the Turbocharger Inspection Procedure Toolbox-Powertrain-Air Management-Boost test and follow the IDS screen prompts, and then continue 1. Remove the turbocharger for inspection with VVT test. Both the boost and VVT test should following Workshop Manual, Section 303-04D: be run in order. Fuel Charging and Controls. 2. Inspect compressor and turbine wheel fins for damage. Replace the turbocharger if fins are damaged. If fins are damaged, inspect the air intake system for damage allowing dirt or contamination to bypass the air filter

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.

Honda Navigation System Information and DVD Information and Inspection Manual

download
REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system