Skip to content

ford ranger heater hose diagram 98

You search PDF repair manual about ford ranger heater hose diagram 98, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Ford Windstar Intake Manifold-Lower Removal And installation manual

download
Intake Manifold—Lower Removal 1. Partially drain the cooling system. For additional information, refer to Section 303-03 . 2. Remove the upper intake manifold (9424). For additional information, refer to Intake Manifold—Upper in this section. 3. Remove the fuel supply manifold (9F792). For additional information, refer to Section 303-04B . 4. Disconnect the EGR vacuum tube (9E498). 5. Disconnect the EGR-to-exhaust manifold tube (9D477). * Loosen the nut. 6. Disconnect the upper radiator hose (8260). * Reposition the clamp. * Disconnect the hose. 7. Disconnect the heater hose (18472). * Compress the fitting * Disconnect the hose. 8. Disconnect the intake manifold runner control (IMRC). 9. Position the water bypass tube (8555) aside. 1. Remove the bolts. 2. Position the tube aside. 10. NOTE: Note the location of the six long bolts. Remove the lower intake manifold (9J447). 1. Remove the bolts. 2. Remove the intake manifold. 11. Remove the intake manifold runner control (IMRC) if necessary. For additional information, refer to Section 303-14 . 12. Remove and discard the lower intake manifold sealing components. Installation 1. Refer to the illustration for intake manifold sealing component locations. 2. Install the lower intake manifold front and rear end seals. 1. Apply a bead of sealant to the intake manifold front and rear end seal mounting points as indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Install the lower intake manifold front and rear end seals. 3. Install the intake manifold gaskets (9439). 4. Install the intake manifold runner control (IMRC) if required. For additional information, refer to Section 303-14 . 5. NOTE: The lower intake manifold must be installed within four minutes of applying sealant. Position the lower intake manifold. 1. Apply a bead of sealant to the lower intake manifold mounting at the points indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Position the lower intake manifold.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

1998 Ford Ranger Heavy Duty Floor Crane Workshop Manual

download
1. Relieve the fuel pressure. For additional information, refer to Section 310-00 . 2. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 3. Drain the engine cooling system. For additional information, refer to Section 303-03 . 4. Remove the hood (16612). 5. Remove the air cleaner outlet tube (9B659). For additional information, refer to Section 303-12 . 6. Remove the accelerator control splash shield (9E766). 7. Remove the upper radiator hose (8260). 8. Remove the lower radiator hose (8286). 9. Remove the two bolts and position the fan shroud (8146) on the fan blade (8600). 10. Remove the water pump pulley, fan and shroud; refer to Section 303-03 . 11. Disconnect the radiator overflow tube. 2. On vehicles equipped with automatic transmissions, disconnect the transmission cooler lines. 13. Disconnect the mass air flow sensor. 14. Disconnect the heater water hoses (18472) at the inlet and outlet; refer to Section 303-03 . 15. Disconnect the power connection from the generator (10346). 16. Disconnect the vacuum connection to the vacuum reservoir. 17. Disconnect the throttle body heater hose. 18. Disconnect the A/C cycling switch. 19. Disconnect the connector from the powertrain control module (PCM) (12A650). 20. Remove the nut. 21. Remove the ground wire stud from the powertrain control module. 22. Recover the A/C system; refer to Section 412-00 . 23. Disconnect the power steering cut-out switch. 24. Disconnect the peanut fitting from the A/C condenser core (19712). 25. Disconnect the A/C high pressure cut-out switch. 26. Disconnect the A/C manifold hose. 27. Remove the nut. 28. Disconnect the accelerator cable (9A758) and the speed control cable. 29. Disconnect the brake booster vacuum hose and vacuum tube at the upper intake manifold assembly. 30. Disconnect the EVR vacuum supply hose and the vacuum reservoir vacuum line. 31. Disconnect the wiring connector. 32. Disconnect the fuel line; refer to Section 310-01 . 33. Remove the A/C compressor; refer to Section 412-03 . 34. Disconnect the power steering pressure and return hoses. 35. Remove the nut retaining the wiring harness. 36. Disconnect the block heater if equipped. 37. Raise the vehicle on a hoist; refer to Section 100-02 . 38. Disconnect the engine ground cable

2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.