ford taurus fuel tank sensor location

You search PDF repair manual about ford taurus fuel tank sensor location, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ford taurus fuel tank sensor location Direct Download speed 5432 Kb/s

  ford taurus fuel tank sensor location Full Version speed 8172 Kb/s



2000 Ford Windstar INCORRECT FUEL GAUGE INDICATION Workshop Manual

0

Filed Under (Ford Manuals) by admin on 12-05-2012

download
The fuel gauge does not change indication unless there has been at least 3 gallons of fuel added or deleted between ignition switch cycle. Use recorded REM and instrument cluster DTCs from the Continuous and On- Demand self-test. ? Are any DTCs recorded? Yes If REM DTC B1201 or IC DTC U1131 is retrieved, GO to D6 . No GO to D2. D2 CARRY OUT THE ICM FUEL GAUGE ACTIVE COMMAND IC Active Command Select the IC FUEL GAUGE CONTROL active command. Trigger FUELLEVEL active command. Toggle and monitor the fuel gauge while adjusting the FUELLEVEL active command to read 50% and 100% Did the fuel gauge needle start at empty (E), move to half at 50%, and full (F) at 100%? Yes GO to D3. No INSTALL a new instrument cluster; REFER to Instrument Cluster. CLEAR the DTC. REPEAT the instrument cluster self-test. D3 CHECK THE FUEL GAUGE READING Fuel Pump Module C412 Connect one lead of Instrument Gauge System Tester to fuel pump module C412 Pin 5, Circuit 1357 (LB/YE), harness side. Connect the other lead to fuel pump module C412 Pin 8, Circuit 1356 (LG/VT), harness side. Set the power switch on Instrument Gauge System Tester to the ON position Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Set Instrument Gauge System Tester to 160 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read full or above. Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read empty or below Does the fuel gauge operate correctly? Yes GO to D4. No GO to D6. D4 INSPECT THE FUEL TANK Visually inspect the fuel tank for any damage or deformation. ? Is the fuel tank OK? Yes GO to D5. No INSTALL a new fuel tank. REFER to Section 310-01. TEST the system for normal operation. D5 INSPECT THE FUEL LEVEL SENSOR AND PUMP ASSEMBLY Visually inspect the fuel pump assembly for damaged wiring or connectors. Visually inspect the float and float rod for damage or obstruction

Related Content:

are there any adj to the vp44, 2005 kia sorento normal teperature, 2005 aztek gas gauge not working, isuzu rodeo self calibrate fuel gauge calibration, ford explorer gas gauge not working, fuel canister disassemble 2001 nissan sentra, fuel guage 2003 buick century, How to fix a gas gauge 2005 impala, how to repair 1996 buick regal temperature gauge, how to repair 2006 f160 cluster

2004 Audi A4 L4-1.8L Turbo FWD Fuel Pump Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 18-04-2011

download
FWD Notes Removing And Installing Fuel Pump CAUTION: To remove the Fuel Pump (FP), the fuel tank may only be filled to a maximum of 3/4. Empty fuel tank if necessary. Recommended special tools and equipment 3087 wrench for tank sensor VAS5190 fuel siphoning device Empty fuel tank Observe safety precautions. Observe rules for cleanliness. CAUTION: Observe safety precautions when disconnecting the battery. Disconnect battery Ground (GND) strap with the ignition switched off. CAUTION: Secure Ground (GND) wire of VAS5190 to a blank portion of the chassis. Pull cone piece -2- from shaft piece -1- of VAS 5190. Using insulating tape, apply a mark -arrow- on hose at length a = 1465 mm from end of suction hose. Remove fuel filler cap from fuel filler tube Screw shaft piece -1- of VAS 5190 fuel siphoning device on to fuel filler tube of fuel tank . Now slide suction hose as far into fuel tank until the mark applied earlier -arrow- stands on shaft piece. NOTE: If using a siphoning device without shaft piece, proceed principally in the same manner In this case, apply a mark -arrow- on hose at length a = 1400 mm from end of suction hose using insulating tape. The suction hose is inserted correctly when the marking applied earlier stands opposite the lip of fuel filler tube. If the hose can only be inserted with difficulty, smear it thinly with engine oil. Never use lubricants containing silicon. Drain fuel tank through fuel filler tube. Carefully remove siphoning hose. Removing Sedan: Remove luggage compartment lining. Push forward the right backrest of rear seat, if necessary. Avant: Remove left 1/3 backrest. Remove left side trim in luggage compartment and dirt tray. All: Remove cover for connector flange (arrows). Release and disconnect harness connector -1-. Disengage electrical harness connector -2- and lay it aside. CAUTION: Work on the fuel system must only be performed when engine is cold. Fuel system is under pressure. Before opening system, place rags around the connection area. Then release pressure by carefully loosening connection Mark and disconnect fuel supply line -1- and fuel return line -3- (press release tab). Disconnect ventilation line -2- (press release button).

Related Content:

2010 ford f-150 ventline on fuel tank, 99 Isuzu Amigo Fuel Tank Pressure sensor, @tacomatank com, 2003 frontier fuel tank removal, 2004 chevy suburban fuel system, fuel line diagram for 2004 impala, fuel tank size xj8 1999, is the fuel filler neck discontinued for 99 ford contour

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

0

Filed Under (Ford Manuals) by admin on 28-05-2012

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

Related Content:

where to measure fuel pressure cat 3126, Ford Fusion Open Gas Tank, ford 755 backhoe crank no start, how change fuel pressure regulator on 2006 toyota tocoma, chevy uplander keeps popping fuel line off of tank, gpz 500 fuel tank is it pressurized, grand marquis fuel tank pressure sensor location, how much fuel pressure for 2002 ford 5 4, how to change fuel pressure regulator on 2000 bonniville, how to drain fuel tank rav4 2 2

1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, bp44 repair manual pdf, toyota so5d engine fule pump control wireing diagram pdf, lucas cav injection pump diagram, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 2002 isx cummins manual pump installation, how to change water pump on a dewoo, isuzu dmax fuel pump, cav injector pump governor spring, rager injection pump parts manual

2002 Chevrolet Tahoe – 4WD Fuel Line Disconnect Tool for Fuel Filter Removal/ Installation Procedure on 5.3L Flexible Fuel Engine

0

Filed Under (Chevrolet Manuals) by admin on 17-05-2011

download
2. Install the J 34730-1A . 3. Loosen the fuel fill cap in order to relieve fuel tank vapor pressure. 4. Open the valve on the J 34730-1A in order to bleed the system pressure. The fuel connections are now safe for servicing. 5. Drain any fuel remaining in the gauge into an approved container. 6. Once the system pressure is completely relieved, remove the J 34730-1A . 7. Raise and suitably support the vehicle. Important Clean the fuel filter connections and surrounding area before disconnecting the fuel lines in order to avoid possible fuel system contamination. 8. Using a flare nut wrench and a backup wrench, disconnect the fuel line fitting from the fuel filter. 9. Pull the quick-connect fitting back until the internal retainers hit the filter stop. 10. Twist one end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 11. Twist the opposite end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 12. Once the J 46363 – Fuel Line Disconnect Tool is inserted, ensure the tool is parallel to the filter and the fitting. 13. While holding the filter, push the quick-disconnect fitting towards the filter in order to disconnect the quick- connect fitting. 14. Remove the quick-connect fitting from the filter. 15. Remove the filter from the bracket. 16. Install the new fuel filter, P/N 15173334 or P/N 25164003 (A/C Delco P/N GF847), to the bracket. 17. While holding the filter, push the fitting towards the filter in order to connect the quick-connect fitting. 18. Using a flare nut wrench and a back up wrench, connect the fuel line fitting to the filter. 19. Position the fuel sensor bracket into place and install the two nuts. Tighten Tighten the two nuts to 17 N·m(13 lb ft). 20. Lower the vehicle. 21. Tighten the fuel cap. 22. Connect the negative battery cable.

Related Content:

2002 tahoe fuel line, fuel pump gas line hose diagram kia optima, fuel line diagram for 2002 ford taurus, 2011 Rav4 fuel filter location, 01 sable fuel pump wireing, fuel filter isuzu 8981499820 replacement vic & device, firing order 2005 chev uplander 3 5 L, Echo ES 210 Fuel Line, 87 chevy fuel line routing, 2011 e350 ford fuel filter

1997 Ford F-250/350/Super Duty Fuel Tank, Filters, Tubes and Electric Fuel Pump, Gasoline Engines Repair Manual

0

Filed Under (Ford Manuals) by admin on 17-05-2011

download
Item Part Number Description 1 370443-S32 Push-On Clip 2 9G291 Rear Fuel Vapor Return Tube 3 9A317 Fuel Tube Clip 4 9J337 Rear Fuel Supply and Return Tube 5 2269 Brake Tube 6 N802769-S Clip, Double 7 9291 Fuel Tube 8 N808716-S190 Retainer with Tether 9 9J338 Fuel Rail Tube 10 N802768-S Clip, Single 11 N605895-S2 Bolt 12 9K337 Fuel Tube Clip Support Bracket 13 N620480-S2 Nut 14 9002 Fuel Tank 15 9B033 Fuel Vapor Tube 16 9H334 Dual Fuel Supply and Return Tube 17 44878 Washer 18 N802826-S Screw 19 N620482-S2 Nut 20 383521-S Clamp 21 381114 Hose, 3/8-Inch 22 9H336 Front Fuel Tube and Hose 23 9A335 Fuel Filter Bracket 24 9B273 Fuel Filter to Fuel Pump Tube 25 N606678 Bolt

Related Content:

2004 ford f150 fuel vapor tube

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

Related Content:

MERCEDES BENZ KE JETRONIC FUEL SYSTEM TROUBLE TRACER, ford 550 backhoe operator manual, procedure for overhauling a gear pump, dpa injector pump govenor spring settings, ford 555c alternator wiring diagram, Lucas feul injector pump type 908 for tractor, how to repair fuel injectors on 2003 GMC Envoy, n14 cummins troubleshooting, j-38791 moore, mack 2001 fuel system

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

wire diagram on a 2002 grand prix headlight, 1998 jimmy fuel pump install, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, 2005 tundra speed pulse signal wire location, location of vent valve solenoid on 2010 ford ranger, pontiac grand am fuel pump wireing harness replacement instructions, vcm ground wire

1996 Ford Taurus Camshaft Position Sensor removal and installation manual

0

Filed Under (Ford Manuals) by admin on 16-06-2012

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on ocator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate CMP sensor electrical connector in the pre-removal position. 4. Rotate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear. 5. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees. 6. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14- 22 lb ft)

Related Content:

2003 explorer impact sensor, howtoinstallnewairbagsenscoron2004chevy1500pickuptruck, how to change 2010 hhr cam sensor, 2004 nissan quest o2 sensor, 2005 chevy trailblazer camshaft position sensor install, Is there a resister on a 2008 ford 5 4 triton, 2007 toyota tundra camshaft position sensor removal, testing Catipiller cam senser, 2005 Tahoe Repair Manual PDF, how much to repair cam timing sensor in nissan frontier

2000 Toyota Celica GT-S L4-1762cc 1.8L FUEL PUMP ASSEMBLY Removal and Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 08-11-2011

download
Protect the disconnected fuel tube from damage and foreign material by covering it with a plastic bag. a. Remove the 8 bolts and fuel tank vent tube set plate. b. Pull out the fuel pump assembly. NOTE: Do not damage the fuel pump filter. Be careful that the arm of the sender gauge should not bent. c. Remove the gasket from the pump assembly. a. Install the new gasket to the fuel pump assembly. b. Install the fuel pump assembly to the fuel tank . NOTE: Do not damage the fuel pump filter. Be careful that the arm of the sender gauge should not bent. c. Install the 8 bolts and fuel tank vent tube set plate from the fuel tank . Torque: 4.0 Nm (40 kg.cm, 35 in.lb) a. Clean up around the fuel tube. b. Connect the fuel tube and emission tube to the fuel pump assembly. c. Connect the tube joint clip to the fuel suction plate. HINT: Start the engine, check for fuel leakage

Related Content:

are there any adj to the vp44, 2005 kia sorento normal teperature, 2005 aztek gas gauge not working, isuzu rodeo self calibrate fuel gauge calibration, ford explorer gas gauge not working, fuel canister disassemble 2001 nissan sentra, fuel guage 2003 buick century, How to fix a gas gauge 2005 impala, how to repair 1996 buick regal temperature gauge, how to repair 2006 f160 cluster