Skip to content

ford windstar steering column removal

You search PDF repair manual about ford windstar steering column removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

1997 Ford Thunderbird/ Cougar Steering Column Removal And Installation Manual

download
Steering Column Disassembly CAUTION: Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle unless the column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated, as this will damage the air bag sliding contact. 1. Disconnect battery ground cable (14301). Refer to Section 14-01 . 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725), steering column upper bearing spring (3520), suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539). Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) assembly. 7. Remove bearing retainer (3C610) and steering column upper bearing spring. . Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518). 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear. 12. Remove two pivot bolts. Use caution becausesteering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511). 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723). 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681).

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

2000 Ford Windstar Intake Manifold-Lower Removal And installation manual

download
Intake Manifold—Lower Removal 1. Partially drain the cooling system. For additional information, refer to Section 303-03 . 2. Remove the upper intake manifold (9424). For additional information, refer to Intake Manifold—Upper in this section. 3. Remove the fuel supply manifold (9F792). For additional information, refer to Section 303-04B . 4. Disconnect the EGR vacuum tube (9E498). 5. Disconnect the EGR-to-exhaust manifold tube (9D477). * Loosen the nut. 6. Disconnect the upper radiator hose (8260). * Reposition the clamp. * Disconnect the hose. 7. Disconnect the heater hose (18472). * Compress the fitting * Disconnect the hose. 8. Disconnect the intake manifold runner control (IMRC). 9. Position the water bypass tube (8555) aside. 1. Remove the bolts. 2. Position the tube aside. 10. NOTE: Note the location of the six long bolts. Remove the lower intake manifold (9J447). 1. Remove the bolts. 2. Remove the intake manifold. 11. Remove the intake manifold runner control (IMRC) if necessary. For additional information, refer to Section 303-14 . 12. Remove and discard the lower intake manifold sealing components. Installation 1. Refer to the illustration for intake manifold sealing component locations. 2. Install the lower intake manifold front and rear end seals. 1. Apply a bead of sealant to the intake manifold front and rear end seal mounting points as indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Install the lower intake manifold front and rear end seals. 3. Install the intake manifold gaskets (9439). 4. Install the intake manifold runner control (IMRC) if required. For additional information, refer to Section 303-14 . 5. NOTE: The lower intake manifold must be installed within four minutes of applying sealant. Position the lower intake manifold. 1. Apply a bead of sealant to the lower intake manifold mounting at the points indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Position the lower intake manifold.

1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.