Skip to content

free 2000 montero sport manual

You search PDF repair manual about free 2000 montero sport manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Mitsubishi Truck Montero Sport Evaporator Core Removal and Installation Manual

download
EVAPORATOR REMOVAL AND INSTALLATION REMOVAL SERVICE POINT SUCTION PIPE OR HOSE, DISCHARGE PIPE DISCONNECTION CAUTION: Seal the hoses completely, otherwise the compressor oil and receiver will absorb water vapor easily, possibly damaging the condenser and deteriorating performance. Plug the disconnected hose and the evaporator nipple to prevent foreign material from getting into them. INSTALLATION SERVICE POINT >A< EVAPORATOR INSTALLATION When replacing the evaporator, refill it with the specified amount of compressor oil and install it (to the vehicle).

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

download
2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS The mounting procedure outlined below covers the 2000 – 2006 Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the bumper and the rear cross member. Remove the skid plate. Some vehicles are equipped with an additional skid plate that wraps up in front of the bumper. This skid plate must be removed also. 2. Remove the bolts connecting the tow hook, tie down brackets, and skid plate brackets (Refer to Figure 1) to the bottom of the frame. The bolts and tow hook will be used in the undercarriage installation. 3. Assemble Driver Side Push Beam Support Plate (62B) to the bottom of the driver side frame rail. Begin by installing the bolts removed in Step 2 into the two holes in the bottom of Diver Side Push Beam Support Plate (62B) . Tighten these two bolts. Next, drill the inside and outside frame wall for the upper hole in Driver Side Push Beam Support Plate (62B). Install one ½”-13 X 4-1/2″ Hex Head Bolt (D) and one ½”-13 Lock Nut (B) in the drilled hole. Tighten this bolt. 4. Repeat Step 3 on the passenger side frame rail. Include the tow hook over Passenger Side Push Beam Support Plate (62A). The skid plates, tie down brackets, and skid plate brackets (See Figure 1) will no longer be used but should be retained in case the undercarriage is ever removed. 5. Install Push Beam Assembly (62) between Push Beam Support Plates (62A & 62B) using eight ½”-13 X 1-1/2″ Hex Head Bolts (A) and eight ½”-13 Lock Nuts (B). For Light Duty Plow applications, the center of the receiver hole in Push Beam Assembly (62) should be 14-1/2″ from the ground. Leave hardware finger tight. 6. Assemble Angle Bracket (75) to the back of Push Beam Assembly (62) using four ½”-13 X1- 1/2″ Hex Head Bolts (A) and four ½”-13 Lock Nuts (B). Leave hardware finger tight. 3 7. Assemble the rear portion of Angle Bracket (75) to the truck’s cross member using two Nut Plates (101), two ½” Split Lock Washers (C) and two ½”-13 X 1-1/2″ Hex Head Bolts (A) . Nut Plates (101) must be inserted into the cross member through the large hole in the rear of the cross member. 8. Tighten all hardware beginning at the rear of Angle Bracket (75) and working forward. 9. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

2000 Saturn SL2 L4-1.9L DOHC VIN 7 Body/ Electrical Service Manual

download
1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^If ignition lock cylinder cannot be rotated to RUN position, continue with next step. 5. Using a light hammer and brass drift, tap lightly on the top side of the ignition housing assembly at the location indicated in the illustration, while trying to turn the ignition key. ^If the ignition key turns, proceed to step 30. ^If the ignition key does not turn replace the ignition module/passlock sensor by continuing with next step. 6. Disable SIR system. Refer to “Disabling Frontal Inflators” procedure in the 2000/2001 S-Series Body Electrical Volume II Service Manual