Skip to content

free 2001 hyundai xg300 repair manual

You search PDF repair manual about free 2001 hyundai xg300 repair manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996-2001 Honda Civic – ALL Civic Rear Main Oil Seal Leaks Repair manual

download
REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine warm up to its normal operating temperature (the cooling fan cycles twice). Let the engine idle (throttle fully closed with all electrical items turned off) for 10 minutes. 8. 2001 2-door EX and LX models only. Drive the vehicle above 40 mph for 5 to 10 minutes with the cruise control on. (This lets the cruise control actuator learn how much slack there is in the throttle cable.)

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following: