Skip to content

free 2002 honda odyssey repair manual online

You search PDF repair manual about free 2002 honda odyssey repair manual online, if there are search results will appear below. If search results do not exist, please search by others keyword.

HONDA Accord V6, Odyssey, Pilot Idle Vibration or Harsh Shifting Repair Manual

SYMPTOM There is a vibration at idle or harsh engagement when shifting the transmission between between Park, Drive, and Reverse. PROBABLE CAUSE The front hydraulic engine mount may have deteriorated and torn. PARTS INFORMATION Front Engine Mount Assembly: 1998-02 Accord V6 – P/N 50810-S87-A82, H/C 7981657 1999-04 Odyssey – P/N 50800-S0X-A04, H/C 7978927 2003-05 Pilot – P/N 50800-S3V-A82, H/C 7984560 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Failed Part: P/N 50810-S87-A81 H/C 5438593 Defect Code: 01102 Symptom Code: 04501 Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. DIAGNOSIS 1. Bring the engine up to operating temperature, and fully apply the parking brake. 2. Have an assistant view the top of the front engine mount while standing to the side of the vehicle. Shift the transmission to Drive. With your foot firmly on the brake pedal, quickly depress the accelerator pedal and release it. Your assistant should look for contact between the top of the engine mount and the bottom of the front engine mount bracket, and listen for noise from that area. REPAIR PROCEDURE 1. Drive the vehicle onto a lift, but do not raise it. 2. Odyssey – Remove the intake manifold cover and the front ignition coil cover: •See page 9-4 of the 1999-04 Odyssey Service Manual. •Online, enter keyword INTAKE , and select Intake Manifold Removal and Installation from the list. 3. Odyssey – Remove the radiator cover: •See page 10-16 of the 1999-04 Odyssey Service Manual. •Online, enter keyword RADIATOR , and select Radiator and Fan Replacement from the list

HONDA CR-V Moan or Groan From the Rear Differential REPAIR PROCEDURE

REPAIR PROCEDURE: 2002-04 MODELS 1. Replace the rear differential fluid: •Refer to page 15-13 of the 2002-04 CR-V Service Manual , or •Online, enter keywords REAR DIFF, and select Rear Differential Fluid Inspection and Replacement (4WD) from the list. 2. Raise the vehicle on a lift until all four wheels are completely off the ground and can rotate freely. 3. Start the engine, and let it idle until the radiator fan cycles on and off twice. 4. Burnish the rear differential clutches: Automatic transmission models – •Set the parking brake, and shift the transmission to D. Let the engine idle for 5 minutes. •With the shift lever in D, release the parking brake, keep the wheel speed at 10 mph, and let all four wheels rotate freely for 5 minutes. •Apply the brakes to stop the wheels, repeat the bulleted steps one more time, then go to step 5. Manual transmission models – •With the engine idling and the parking brake released, shift the transmission into 1st, release the clutch, and let the wheels rotate for 5 minutes. •Disengage the clutch, and apply the brakes to stop the wheels. Shift the transmission into reverse, release the clutch, and let the wheels rotate for 5 minutes. •Shift the transmission into neutral, then apply the brakes to stop the wheels. •Repeat the bulleted steps one more time, then go to step 5. 5. Shift the transmission to P (A/T) or neutral (M/T), and turn off the engine. 6. Let the rear differential cool for 10 minutes

Honda Navigation System Information and DVD Information and Inspection Manual

REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system


FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Honda Idle Fluctuation and/or the MIL Is On With DTC P1129 and/ or P0505 Repair Manual

DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation? Yes – Odyssey : Go to REPAIR PROCEDURE A. Pilot : Go to REPAIR PROCEDURE B. No – Go to step 2. 2. Connect the HDS to the vehicle’s DLC, and check for DTCs. Is DTC P1129 or P0505 stored? Yes – Go to REPAIR PROCEDURE B. No – Continue with normal troubleshooting. REPAIR PROCEDURE A 1. Connect the HDS to the vehicle’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading 4. From the System Selection Menu screen, select PGM-FI . 5. From the Mode Menu, select DATA LIST . 6. Scroll down the list to PSP SWITCH . Watch the reading in the Value column. 7. Check for a broken power steering pressure switch wire by wiggling the P/S pressure switch wire harness at the switch while you check the Value column reading. •If the reading changes between on and off when you wiggle the harness, go to step 8. •If the reading does not change between on and off when you wiggle the harness, go to REPAIR PROCEDURE B. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. NOTE: You may need to disconnect the Secondary HO2S connector to free the end of the harness from the body. 10. Lower the vehicle, and pull the harness up for easier access to make the repair. 11. Remove the rubber seal from the connector, and remove the terminals from the connector noting the GRN wire and BLK wire locations. 12. Remove the tape from the corrugated tube and the wires up to the harness clip; mark the wires at the end of the corrugated tube