Skip to content

free download 2001 dodge durango 5 9l v8 sevice manual

You search PDF repair manual about free download 2001 dodge durango 5 9l v8 sevice manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

2002 Dodge Neon Power Steering Belt Service and Repair Manual

download
Power Steering Belt REMOVAL POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be removed from power steering pump pulley. Gently, release spring tension on tensioner. 2. Remove the drive belt (Fig. 3). Clean all foreign debris from belt pulley grooves. The belt pulleys must be free of oil, grease, and coolants before installing the drive belt. INSPECTION Belt replacement under any or all of the following conditions is required: ^Excessive wear ^Frayed cords ^Severe glazing Poly-V Belt system may develop minor cracks across the ribbed side (due to reverse bending). These minor cracks are considered normal and acceptable. Parallel cracks are not (Fig. 6). NOTE: Do not use any type of belt dressing or restorer on Poly-V Belts. INSTALLATION NOTE: When installing drive belt on the pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves. POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Install the drive belt (Fig. 3) over all the pulleys except for the power steering pump pulley 2. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be installed on the power steering pulley Release spring tension onto belt. 2002 Dodge Neon L4-2.0L VIN C Copyright © 2009, ALLDATA 9.90 Page 4 3. After belt is installed, inspect belt length indicator marks (Fig. 7). The indicator mark should be within the minimum belt length and maximum belt length marks. On a new belt, the indicator mark should align approximately with the nominal belt length mark

1996-2001 Honda Civic – ALL Civic Rear Main Oil Seal Leaks Repair manual

download
REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine warm up to its normal operating temperature (the cooling fan cycles twice). Let the engine idle (throttle fully closed with all electrical items turned off) for 10 minutes. 8. 2001 2-door EX and LX models only. Drive the vehicle above 40 mph for 5 to 10 minutes with the cruise control on. (This lets the cruise control actuator learn how much slack there is in the throttle cable.)

2003-2007 Dodge (DR/DH/D1/DC) Ram Truck Front EndShimmy On 4×4 Vehicles When Traveling Over Rough Surfaces In The Road

download
REPAIR PROCEDURE: 1. Raise the vehicle on an alignment rack (drive-on lift). 2. Verify the road tires are correctly sized and the tire tread is not excessively worn. Replace any worn tire before proceeding. Any new or old replacement tire should be equal to the original tires that came with the vehicle when it was new. Tire wear is not covered by the vehicle warranty. 3. Set the tire pressure for the FRONT TIRES to the following specification, regardless of the load being carried by the vehicle . Tire Size FRONT Tire Pressure LT235/80R17EorLT245/70R17E 448 Kpa (65 psi) LT265/70R17EorLT285/70R17E 414 Kpa (60 psi) 4. Set the tire pressure for the REAR TIRES as recommended for the vehicle configuration and load that is being carried at the time. Tire Size REAR Tire Pressure LT235/80R17EorLT245/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. LT265/70R17EorLT285/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. 5. Verify that the steering damper is operating correctly. a. Unbolt the end of the damper at the axle end. b. Cycle the damper rod by hand. c. There should be resistance to motion in both directions of the damper rod. d. Replace the damper if no resistance is present. 6. Verify both outer tie rod ends dustcovers are not worn. a. Attempt to rotate the dustcover by hand. b. If the dustcover on an outer tie rod end can be rotated, or is free and loose, then replace the tie rod (regardless of joint wear). 7. Inspect each outer tie rod end for internal wear. a. Maximum allowed wear (joint travel) fora tie rod end is 1.15 mm (0.045 in.). b. Install a dial indicator to the tie rod end (in-line with the vertical stud of the tie rod end). c. With a pry bar placed between the steering linkage and the axle tube, pry upwards while measuring the amount of joint travel (wear). d. Measure the amount of wear in the other outer tie rod end joint. e. If wear (joint travel) in either outer tie rod end is greater than 1.15 mm (0.045 in.), then replace the worn tie rod end. 8. Verify the torque on each outer tie rod end stud nut. The nut should be tightened to 122 Nm (90 ft. lbs.). 9. Make sure any worn outer tie rod ends have been replaced before proceeding further. 10. Verify all other steering linkage connections are tightened to their torque specifications.