Skip to content

free download 4r70w rebuild

You search PDF repair manual about free download 4r70w rebuild, if there are search results will appear below. If search results do not exist, please search by others keyword.

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

How To Build a High Performance Cummins Diesel

download
CEO/ Diesel Injection of Pittsburgh Keep in mind while reading this document that it is a gathering of all the articles Bruce has written over the last ten years. There may be some old prices discussed so, to get the latest pricing, check the main page. If you have any questions feel free to call us at 724-274-4080 and we can discuss your horsepower needs. Please have your CPL#. If you are looking for upgrades for your Electronic Celect/Celect Plus Cummins engine visit our Pittsburgh Power site at Pittsburghpower.com. HOW TO BUILD A HIGH-PERFORMANCE CUMMINS DIESEL ENGINE This is a very controversial subject and 99% of the mechanics who build diesel engines will disagree with what we have to say and will probably refuse to build the engine for you. For the owner-operator who loves horsepower do not give up when you speak to the negative mechanic. There are a few good shops throughout the states that will build the ultimate performance engine. Or you can build it yourself as long as you have mechanical knowledge and tools. BUILDING THE ENGINE: In order to have the engine live with high horsepower and run efficiently you must have the right combination of compression ratio, fuel, air and timing. Please do not try to get extreme power simply by increasing the fuel pressure on a stock engine. You will obtain some horsepower, however your compression ratio, air and timing will be wrong. The best time to obtain horsepower is during a rebuild. Since you are going to buy new parts anyway you might as well buy the right combination that produces horsepower and generally the price of the high performance parts is the same as the stock parts. NOW TO THE NUTS AND BOLTS : The compression ratio of the pistons and the timing must go together. High compression pistons belong only in gasoline engines that are naturally aspirated. Turbocharged diesel engines must have low compression pistons in order to produce high horsepower. The lower the compression ratio the less wear on rod bearings and the lower the internal pressure will be when the injector fires. High internal pressure is very detrimental to the life of a piston. When you see a piston with a hole burned through, it’s not the fault of the injector it is a result of internal pressure. To control the pressure we lower the compression ratio and retard the timing. If you compare the compression ratio and timing of an NTC 290 versus an NTC 400 you will see the difference. Where do you think we have to be on the timing to produce 700 horsepower from an NTC?

2003-2007 Dodge (DR/DH/D1/DC) Ram Truck Front EndShimmy On 4×4 Vehicles When Traveling Over Rough Surfaces In The Road

download
REPAIR PROCEDURE: 1. Raise the vehicle on an alignment rack (drive-on lift). 2. Verify the road tires are correctly sized and the tire tread is not excessively worn. Replace any worn tire before proceeding. Any new or old replacement tire should be equal to the original tires that came with the vehicle when it was new. Tire wear is not covered by the vehicle warranty. 3. Set the tire pressure for the FRONT TIRES to the following specification, regardless of the load being carried by the vehicle . Tire Size FRONT Tire Pressure LT235/80R17EorLT245/70R17E 448 Kpa (65 psi) LT265/70R17EorLT285/70R17E 414 Kpa (60 psi) 4. Set the tire pressure for the REAR TIRES as recommended for the vehicle configuration and load that is being carried at the time. Tire Size REAR Tire Pressure LT235/80R17EorLT245/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. LT265/70R17EorLT285/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. 5. Verify that the steering damper is operating correctly. a. Unbolt the end of the damper at the axle end. b. Cycle the damper rod by hand. c. There should be resistance to motion in both directions of the damper rod. d. Replace the damper if no resistance is present. 6. Verify both outer tie rod ends dustcovers are not worn. a. Attempt to rotate the dustcover by hand. b. If the dustcover on an outer tie rod end can be rotated, or is free and loose, then replace the tie rod (regardless of joint wear). 7. Inspect each outer tie rod end for internal wear. a. Maximum allowed wear (joint travel) fora tie rod end is 1.15 mm (0.045 in.). b. Install a dial indicator to the tie rod end (in-line with the vertical stud of the tie rod end). c. With a pry bar placed between the steering linkage and the axle tube, pry upwards while measuring the amount of joint travel (wear). d. Measure the amount of wear in the other outer tie rod end joint. e. If wear (joint travel) in either outer tie rod end is greater than 1.15 mm (0.045 in.), then replace the worn tie rod end. 8. Verify the torque on each outer tie rod end stud nut. The nut should be tightened to 122 Nm (90 ft. lbs.). 9. Make sure any worn outer tie rod ends have been replaced before proceeding further. 10. Verify all other steering linkage connections are tightened to their torque specifications.

1999 Mercury Sable V6-3.0L DOHC A/ T-Cooler Flushing Service Manual

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers. ^They do not provide the volume necessary to remove heavy contaminants. ^They evaporate quickly and essentially leave contaminants in pockets, bends, or wherever they are as the solvent dries. ^TORQSHIFT, 4R100, E40D, C6 – The REAR transmission case filling receives the return line. ^4R70W, AODE, AOD – The TOP transmission case filling receives the return line. ^A4LD, 4R44/55E, 5R55E, 5R55N, 5R55W, 5R55S The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

download
INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.