free download dodge dakota 4x4 repair

You search PDF repair manual about free download dodge dakota 4x4 repair, if there are search results will appear below. If search results do not exist, please search by others keyword.



  free download dodge dakota 4x4 repair Direct Download speed 5432 Kb/s

  free download dodge dakota 4x4 repair Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 6m70 engine manual pdf, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, pdf kancil 850 manual tranission, 2006 ford focus ses repair manual, 1996 buick regal 3800 owners mAnuel

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, Replacing the reverse band Dodge 1500, 2010 silverado 1500 4 3 liter canister vavle solenoid, repair manual for 1998 chevrolet 1500, ax12-1500 nut torque, downloadable schematic for 99 Chevy suburban evap system, parts manual for lazy boy reclin, Pcv valve 2005 gmc 1500

Honda Idle Fluctuation and/or the MIL Is On With DTC P1129 and/ or P0505 Repair Manual

0

Filed Under (Honda Manuals) by admin on 07-05-2012

download
DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation? Yes – Odyssey : Go to REPAIR PROCEDURE A. Pilot : Go to REPAIR PROCEDURE B. No – Go to step 2. 2. Connect the HDS to the vehicle’s DLC, and check for DTCs. Is DTC P1129 or P0505 stored? Yes – Go to REPAIR PROCEDURE B. No – Continue with normal troubleshooting. REPAIR PROCEDURE A 1. Connect the HDS to the vehicle’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading 4. From the System Selection Menu screen, select PGM-FI . 5. From the Mode Menu, select DATA LIST . 6. Scroll down the list to PSP SWITCH . Watch the reading in the Value column. 7. Check for a broken power steering pressure switch wire by wiggling the P/S pressure switch wire harness at the switch while you check the Value column reading. •If the reading changes between on and off when you wiggle the harness, go to step 8. •If the reading does not change between on and off when you wiggle the harness, go to REPAIR PROCEDURE B. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. NOTE: You may need to disconnect the Secondary HO2S connector to free the end of the harness from the body. 10. Lower the vehicle, and pull the harness up for easier access to make the repair. 11. Remove the rubber seal from the connector, and remove the terminals from the connector noting the GRN wire and BLK wire locations. 12. Remove the tape from the corrugated tube and the wires up to the harness clip; mark the wires at the end of the corrugated tube

1999 GMC Truck Yukon PRNDL Display Inaccurate or Inoperative PRNDL Inaccurate Repair Manual

0

Filed Under (GMC Manuals) by admin on 15-02-2012

download
Did you perform the Instrument Cluster System Check? — Go to Step 2 Go to Instrument Cluster System Check 2 1. Disconnect the Transmission Range (TR) Switch connector C2. 2. Turn the ignition switch to the RUN position. 3. Conduct the PRNDL Logic Input Test by connecting fused jumper wires between ground and the appointed cavities of the TR Switch connector. Refer to PRNDL Logic Input Test PRNDL Logic Input Test . 4. Repeat for each transmission range. Do all ranges illuminate? — Go to Step 3 Go to Step 4 3 Adjust the transmission range switch. Refer to Park/Neutral Position Switch Adjustment (4L60E); Park/Neutral Position Switch Adjustment (4L80E) Automatic Transmissions. Replace the PNP Switch. Refer to Park/Neutral Position Switch Replacement (4L60E); Park/Neutral Position Switch Replacement (4L80E) in Automatic Transmissions. Is the repair complete? — Go to Instrument Cluster System Check — 4 1. Remove the I/P Cluster. 2. Connect a J 39200 DMM (continuity) between the I/P Cluster connector and connector C2 of the TR Switch to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 6 Go to Step 5 5 Locate and repair the open in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 6 Connect a J 39200 DMM (continuity) between the I/P Cluster connector and ground to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 7 Go to Step 8 Locate and repair the short to ground in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring 7 Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 8 Replace the I/P Cluster. Refer to Instrument Panel Cluster (IPC) Replacement . Is the repair complete?

Related Content:

07tahoe dashboard repair kit, 1996 buick instrument cluster problems, 1999 yukon radiator removal instructions, 2006 buick torrent PRNDIL?, 2006 nissan quest odometer repair sacramerto area, GM IPC CIRCUIT BOARDS

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

0

Filed Under (Honda Manuals) by admin on 17-02-2012

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

Related Content:

2004 isuzu axiom how to bypass security, 02 saturn sl2 no start, free 1996 Honda accord lx repair manual, Free Transmission Manuals Downloads, honda civic 2007 cvt transmision sensors detail pdf, honda civic 2009 repair manual pdf, honda civic shudder ac, Honda Fit Clutch Replacement, how to use a compressor clutch tool honda civic, ISUZU AXIOM P0346

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

how to replace solenoid e on a245e transmission problems, yhs-lavasoft, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2004 saturn Clutch Assembly Exploded View, rf-d9br-7006-ab gear radio

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

4t65e documentation pdf, atsg 4t65e tech manual, 01J atsg technical repair manual torrent, 4t65e pdf

1999 Audi A6 Sedan Timing Belt Service and Repair

0

Filed Under (Audi Manuals) by admin on 04-06-2011

download
Toothed belt, removing and installing Removing – Remove engine cover (arrows). – Remove noise insulation panel (arrows). – Remove front bumper. Refer to Body and Frame/Bumper/Service and Repair – Move lock carrier to service position. Refer to Body and Frame/Radiator Support/Service and Repair – Remove ribbed belt. Refer to Engine/Drive Belts, Mounts, Brackets and Accessories/Drive Belt/Serpentine Belt/Service and Repair See: Drive Belt/Service and Repair CAUTION: Mark the running direction of the belt with a crayon or marker before removing. Reinstalling a used belt in reversed running direction could damage the belt. – Unclip toothed belt guard on both sides and remove. – Turn crankshaft by hand to TDC. Marks -A- and -B- must align – Check position of camshafts. Larger holes (arrow) of securing plates on camshaft sprockets must be on inside and must align If they are not in this position: Turn crankshaft one revolution further. – Remove sealing plug from left-side of cylinder block. Top Dead Center (TDC) mark on crankshaft must be visible or can be felt Crankshaft Holder 3242 Shown In Installed Position – Install 3242 crankshaft holder into opening. – Remove tensioner for ribbed belt. – Remove center and left belt guards. Notes: The toothed belt tensioner is oil-dampened. Compress it by slowly applying constant pressure. Use spring clamp from 2024A. – Using 8 mm hex wrench, turn toothed belt tensioning roller -1- counter-clockwise, opposite direction shown (arrow), until tensioning lever -2- compresses tensioner -3- so that spring clamp (2 mm dia.) can be inserted into bore and lifter. – Insert pin and release tension. – Remove vibration dampener. Refer to Engine/Cylinder Block Assembly/Harmonic Balancer/Service and Repair – Remove idler for ribbed belt and guard under vibration dampener (arrows). – Remove toothed belt.

Related Content:

Repair roller lifter

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram