Skip to content

free repair manual for 1999 honda crv

You search PDF repair manual about free repair manual for 1999 honda crv, if there are search results will appear below. If search results do not exist, please search by others keyword.

HONDA Accord V6, Odyssey, Pilot Idle Vibration or Harsh Shifting Repair Manual

download
SYMPTOM There is a vibration at idle or harsh engagement when shifting the transmission between between Park, Drive, and Reverse. PROBABLE CAUSE The front hydraulic engine mount may have deteriorated and torn. PARTS INFORMATION Front Engine Mount Assembly: 1998-02 Accord V6 – P/N 50810-S87-A82, H/C 7981657 1999-04 Odyssey – P/N 50800-S0X-A04, H/C 7978927 2003-05 Pilot – P/N 50800-S3V-A82, H/C 7984560 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Failed Part: P/N 50810-S87-A81 H/C 5438593 Defect Code: 01102 Symptom Code: 04501 Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. DIAGNOSIS 1. Bring the engine up to operating temperature, and fully apply the parking brake. 2. Have an assistant view the top of the front engine mount while standing to the side of the vehicle. Shift the transmission to Drive. With your foot firmly on the brake pedal, quickly depress the accelerator pedal and release it. Your assistant should look for contact between the top of the engine mount and the bottom of the front engine mount bracket, and listen for noise from that area. REPAIR PROCEDURE 1. Drive the vehicle onto a lift, but do not raise it. 2. Odyssey – Remove the intake manifold cover and the front ignition coil cover: •See page 9-4 of the 1999-04 Odyssey Service Manual. •Online, enter keyword INTAKE , and select Intake Manifold Removal and Installation from the list. 3. Odyssey – Remove the radiator cover: •See page 10-16 of the 1999-04 Odyssey Service Manual. •Online, enter keyword RADIATOR , and select Radiator and Fan Replacement from the list

1996-1998 Civic HX With CVT Shudder, Judder, Surging, Shock, Noise, or Idle Fluctuation Repair Manual

download
PROBABLE CAUSE The problem may have one or more of these causes: •TCM control unit programming is too sensitive. •The start clutch assembly is worn. •The start clutch control valve is contaminated. CORRECTIVE ACTION Replace the start clutch assembly, the start clutch control valve, and the TCM. PARTS INFORMATION Start Clutch Kit: P/N 06220-P2M-305, H/C 7073448 Honda ATF-Z1 (seven quarts required): P/N 08200-9001, H/C 6512628 REQUIRED SPECIAL TOOLS Start Clutch Remover: T/N 07TAE-P4VA120 Start Clutch Installer: T/N 07TAE-P4VA130 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 219167 Flat Rate Time: 6.0 hours Failed Part: P/N 22020-P4V-325 H/C 5192349 Defect Code: 034 Contention Code: C99 Template ID: 02-003A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE NOTE: Make sure the work surface and the CVT are completely clean. Use lint-free towels, and use a dedicated, clean solvent tank for cleaning the CVT parts. If you do not keep everything very clean, the repair may not be successful. 1. Soak the new start clutch assembly in Honda ATF-Z1 for at least 30 minutes. 2. Remove the transmission from the vehicle. See page 14-304 of the 1996-00 Civic Service Manual. 3. Cover with clean shop towels all of the openings in the transmission and anything else that might get damaged by water and cleaning chemicals (axle openings, breather, and electrical connectors). Clean all the dirt and grease off of the transmission before you start disassembly

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

1999 FORD EXPLORER/ RANGER TRANSMISSION-4R44E OR 5R55E-SLIPPING SHIFT/ DELAYED OR NO ENGAGEMENT REPAIR MANUAL

download
SERVICE PROCEDURE F87Z-7A100-DB Main Control (4.0L EI Explorer) F87Z-7A100-EB Main Control (4.0L SOHC Explorer) 1. Perform normal diagnosis for this concern. XL2Z-7L491-AA Bracket XL2Z-7G383-AA Electronic Pressure Control (EPC) 2. Perform Line Pressure Tests as listed in the Solenoid 1999 Explorer/Mountaineer, Ranger Workshop Manual. OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The 3. If pressures are low, perform Pinpoint Test for Provisions Of Bumper To the EPC solenoid. Bumper Warranty Coverage And Emissions Warranty 4. Inspect the bracket that attaches the Torque Coverage Converter Clutch (TCC), Shift Solenoid B OPERATION DESCRIPTION TIME (SSB), Shift Solenoid D/Coast Clutch Solenoid 991610A Replace Electronic 1.2 Hrs. (SSD/CCS), and EPC solenoids to the main Pressure Control (EPC) control for damage. If the bracket is damaged, Solenoid And Clean Main replace both the bracket and solenoid. Control (Includes Time For 5. If the bracket is not damaged, inspect the Road Test) – 4R44E Or solenoid for the affected date code (refer to the 5R55E following Manufacturing Date Code Chart) and 991610B For Line Pressure And ID marking (Figure 1, Views 1, 2, and 3). If the Pinpoint Tests, Use “A” solenoid is one of the affected, replace it. Time As Outlined In The Warranty And Policy MANUFACTURING DATE CODE Manual Date Code Month/Year DEALER CODING 868xx August 1998 CONDITION 869xx September 1998 BASIC PART NO. CODE 870xx October 1998 7G383 01 871xx November 1998 OASIS CODES: 501000, 502000, 50300

Honda Idle Fluctuation and/or the MIL Is On With DTC P1129 and/ or P0505 Repair Manual

download
DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation? Yes – Odyssey : Go to REPAIR PROCEDURE A. Pilot : Go to REPAIR PROCEDURE B. No – Go to step 2. 2. Connect the HDS to the vehicle’s DLC, and check for DTCs. Is DTC P1129 or P0505 stored? Yes – Go to REPAIR PROCEDURE B. No – Continue with normal troubleshooting. REPAIR PROCEDURE A 1. Connect the HDS to the vehicle’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading 4. From the System Selection Menu screen, select PGM-FI . 5. From the Mode Menu, select DATA LIST . 6. Scroll down the list to PSP SWITCH . Watch the reading in the Value column. 7. Check for a broken power steering pressure switch wire by wiggling the P/S pressure switch wire harness at the switch while you check the Value column reading. •If the reading changes between on and off when you wiggle the harness, go to step 8. •If the reading does not change between on and off when you wiggle the harness, go to REPAIR PROCEDURE B. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. NOTE: You may need to disconnect the Secondary HO2S connector to free the end of the harness from the body. 10. Lower the vehicle, and pull the harness up for easier access to make the repair. 11. Remove the rubber seal from the connector, and remove the terminals from the connector noting the GRN wire and BLK wire locations. 12. Remove the tape from the corrugated tube and the wires up to the harness clip; mark the wires at the end of the corrugated tube