Skip to content

free video repair of 2005 kia sorento piston in engine block

You search PDF repair manual about free video repair of 2005 kia sorento piston in engine block, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005-2006 (LX) Chrysler 300/ Magnum/ Charger/ Pacifica Multiple Cylinder Misfire Or Rough Idle Repair Manual

download
REPAIR PROCEDURE: VALVE ROTATION: 1. Relieve the fuel pressure. Refer to the detailed service information available in TechCONNECTunder: Service Info>14-Fuel System>Fuel Delivery >Standard Procedure>Fuel System Pressure Release Procedure. 2. Remove upper intake manifold. Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Manifolds>Intake Manifold> Removal. 3. Remove cylinder head cover(s). Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Cylinder Head>Cylinder Head Cover(s) >Removal. 4. Remove rocker arm and shaft assembly. Refer to the detailed service information available in TechCONNECT under: Service Info >9-Engine>Cylinder Head> Rocker Arm/Adjuster Assembly >Removal). 5. Clean and mark the tip of each exhaust valve stem at the 12 O’clock position witha paint marker. The paint mark will be used later to assist with determining the amount of valve rotation. 6. Remove the sparkplugs. 7. Rotate the crankshaft clockwise, until the number 1 piston is at Top Dead Center (TDC) on the compression stroke. 8. Install the compression tester sparkplug adapter in cylinder#1 sparkplug hole. With air hose attached to sparkplug adapter, apply 620.5 to 689 kPa (90 to 100 psi) air pressure. This is to hold valves into place while servicing components. 9. Using Tool MD 998772A (1) with adapter 6527 (4) or equivalent, slightly compress the exhaust valve spring to release tension against the valve and valve spring retainer ( Fig. 1 ). 10. Remove the valve spring retainer locks and discard the locks. NOTE: It is important that the valve rotation section of this repair procedure be performed.

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

download
HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle