freelander propshaft diagram

You search PDF repair manual about freelander propshaft diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  freelander propshaft diagram Direct Download speed 5432 Kb/s

  freelander propshaft diagram Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix, igt savp parts diagram

Steering, Brake And Suspension Specialists Proportioning Valve Diagram

0

Filed Under (More Manuals) by admin on 01-10-2011

download
This diagram is the most common way to plumb a proportioning valve. In some cases, the right front line will be plugged off at the proportioning valve and the left front line will go to a “T” fitting. From the “T” fitting, the front lines then split off and go to the left and right wheels. Our proportioning valve has a warning light switch built in (this is not a stop light switch.) The warning light will detect any loss of pressure, for example, a leaky wheel cylinder. We recommend you wire this light into your system. Any two wire light socket will work. One wire goes to the accessory power and the other goes to the warning light. Our proportioning valves provide four functions: 1. Proportion pressure front and rear 2. 10 psi. residual check valve 3. Metering valve to apply pressure to the rear brakes before the front brakes 4. A brake warning light to detect a loss in pressure Proportioning Valve Plumbing Diagram: There are two proportioning valve lines that connect to the master cylinder provided in our kits. The first is a 90 degree bend with one leg longer than the other. This line must be oriented with the long leg connected into the front top hole of the proportioning valve and the short end in the front hole on the master cylinder. The second line has two 90 degree bends and has color coded fittings. The larger blue fitting goes into the back hole on the master cylinder and the smaller gold fitting goes into the back top hole on the proportion valve as shown in the diagram

Related Content:

wire diagram brake light pressure switch, brake residual valve, residual pressure valve installation diagram, Residual Valve Brake System

1999 – Current Toyota Tundra Installation Manual

0

Filed Under (Toyota Manuals) by admin on 03-03-2012

download
Step 1: Bedliner Modification Note: If the truck is equipped with a plastic drop-in bedliner, some alteration will be necessary. Ifno bedliner is present, proceed to Step 2. A. The dotted lines in Diagram 1 depict the more common under-the-rail liner modifications. A. 1. Using a jig saw with a medium tooth blade, remove the bulkhead portion of the liner as indicated. A. 2. Be sure to trim the bedliner’s plastic tailgate panel as shown. B. The dotted lines in Diagram 2 depict the less common over-the-rail liner modifications. A. 1. Using a jig saw with a medium tooth blade, remove the top cap and bulkhead portions of the liner as indicated. A. 2. If a rear notch is necessary, placethe tracks on their respective bedrails and mark the positions of the most rearward clamps prior to removing the liner. (The correct position of the track is with the black plastic track end-cap touching the inside surface of the tailgate.) A. 3. When the modification is complete, push the wall of the liner under the bedrail. A. 4. Be sure to trim the bedliner’s plastic tailgate panel as shown Step 2: Shim the OE Bedrail Caps (units 546 & 565) A. Remove the plastic bedrail caps, starting at the tailgate and lifting slowly (Photo 3) . Allow each snap to release as you proceed, being careful not to overstress the rail cap. B. Place the correct stick-on shim pads at the locations shown in Diagram 4. Note: The measurements shown in the graph below are taken beginning from the bulkhead end of the bedrail cap down-flange. Be sure to center the shims at each location and place them agains the down flange as shown in Diagram 5 . Product Code ABCD 546 (all 1/4″ shims) 16″ 37″ 49″ 61″ 1 / 8 ” shim @1/ 4 ” shim @3/ 8 ” shim @1/ 2 ” shim @ 565 18 1/ 2 “37 1/ 2 ” 49″ 60″ C. With

Related Content:

2000 toyota tundra front end parts diagram

2002 Toyota Truck 4 Runner Engine, Cooling and Exhaust Cooling System Radiator Removal and Installation Manual

0

Filed Under (Toyota Manuals) by admin on 21-03-2012

download
REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE RADIATOR GRILLE Remove the 7 clips and radiator grille. 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT RADIATOR RESERVOIR HOSE 5. DISCONNECT LOWER RADIATOR HOSE 6. REMOVE RADIATOR NO.2 FAN SHROUD 7. A/T: DISCONNECT OIL COOLER HOSES 8. REMOVE RADIATOR Remove the 4 bolts and the radiator. DISASSEMBLY 1. REMOVE NO.1 FAN SHROUD Remove the 4 bolts and No. 1 fan shroud. 2. REMOVE RADIATOR SUPPORTS 3. REMOVE DRAIN PLUG 4. ASSEMBLE SST SST 09230-01010 a. Install the claw to the overhaul handle, inserting it in the hole in part “A” as shown in the diagram. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram is 0.2 – 0.3 mm (0.008 – 0.012 inch). NOTICE: If this adjustment is not done, the claw may be damaged. 5. UNCAULK LOCK PLATES Using SST to release the caulking, squeeze the handle until stopped by the stopper bolt. SST 09230-01010 6. REMOVE TANKS AND O-RINGS a. Lightly tap the radiator port (inlet or outlet) with a soft faced hammer, and remove the tank. b. Remove the O-ring. REASSEMBLY 1. INSPECT LOCK PLATE Inspect the lock plate for damage. HINT: If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. NOTICE: The radiator can only be recaulked 2 times. After the 2nd time, the radiator core must be replaced. 2. INSTALL NEW O-RINGS AND TANKS a. After checking that there are no foreign objects in the lock plate groove, install the new O-ring without twisting it. HINT: When cleaning the lock plate groove, lightly rub it with sand paper without scratching it. b. Install the tank without damaging the O-ring. c. Tap the lock plate with a soft-faced hammer so that there is no gap between it and the tank. 3. ASSEMBLE SST 09230-01010 a. Install the punch assembly to the overhaul handle, inserting it in the hole in part “A” as shown in the illustration. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram. Dimension “B”: 8.4 mm (0.34 inch) 4. CAULK LOCK PLATE

Related Content:

2001 ford taurus radiator replacement, 2005 kia sorento radiator diagram, 96 taurus radiator diagram, 1999 cadillac seville how to drain radiator, RADIATOR PRESSURE ADAPTER FOR 95 TOYOTA 4-RUNNER, radiator flush on 2002 crown vic, radiator flush 2000 poniac montana you tube, position of fan switches on peugoet 307 1 4 16 valve, pontiac G6 GT radiator schematics, radiator support hole Plugs 67 mustang

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

0

Filed Under (Land Rover Manuals) by admin on 11-07-2012

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

Related Content:

2002 land rover freelander 2 5 v6 head bolt torque specs, buick lacrosse glove compartment latch, kv6 rod bolts

REV / SPEED METER Vehicle Specific Wiring Diagram Installation

0

Filed Under (Toyota Manuals) by admin on 08-04-2012

download
Installation Precautions ?Do not use electro taps in the installation of this product. Electro taps can become loose over time causing the unit to malfunction. This can also lead to vehicle and product damage. Be sure to use wire crimpers and the included splices for a secure connection. ?Be sure that the harness is not exposed to metal. Always wrap all connections with electrical tape. ?How to use the Fittings Strip 5mm from wire Insert sleeve over wire Bend back exposed wire Place male fitting over This ECU terminal arrangement diagram is viewed from the direction of the arrow. The direction of the ECU varies depending upon the vehicle. Perform the installation work after confirming the connector shape and the number of pins. ?If any abnormal noise or abnormal smell is sensed during the installation work of this product stop the work immediately and contact the distributor or your nearest A*PEX business office Continuing the installation under such conditions may cause an electric shock or fire causing damage to electric devices.

Related Content:

s13 speed meter diagram

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 28-06-2012

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

Related Content:

2001 dodge ram central timer module location, can you repair a central timer unit?, 2000 mazda mpv p0755 code Broken wire, UT Scan Plan, scan tool will not communicate for air bag codes, programing a CTM, ct 20 turbo diagram, control time module rear bumper for 2002 dodge dakota, central timer module 2003 Dodge Dakota replacement, central time moduale dodge durango 2001

1984-1998 Jeep Wagoneer/ Commando/ Cherokee Emission Controls Crankcase Ventilation System (PCV/CCV)

0

Filed Under (Jeep Manuals) by admin on 01-06-2012

download
CCV Fitting See Figures 2 and 3 1. With the engine running, remove the CCV fitting. a. If the fitting is not plugged, a hissing noise will be heard as air passes through the valve. A strong vacuum should also be felt when a finger is placed over the fitting. b. Install the CCV fitting. c. Remove the fresh air hose from the air cleaner assembly and loosely hold a piece of paper over the open end of the hose. After allowing about one minute for the crankcase pressure to reduce, the paper should be sucked against the opening with a noticeable amount of force. 2. Turn the engine OFF . Remove the metered orifice fitting, and check for a plugged condition. A clicking noise should be heard to indicate that the valve mechanism is free. 3. If the crankcase ventilation system meets the tests in Steps 1 and 2 above, no further service is required. If not, the CCV fitting must be cleaned and the system checked again. 4. If Step 1c fails when the CCV fitting is cleaned, it will be necessary to replace the molded vacuum hose with a new one, and to clean the metered orifice port. 5. Clean or replace the engine air cleaner filter element with a new one-for more details, refer to the air cleaner procedure located in General Information & Maintenance. Fig. 2: CCV system diagram for 4.0L engine Fig. 3: CCV system diagram for the 2.5L engine Evaporative Emission Control System OPERATION The evaporative emission control system prevents the release of unburned hydrocarbons, from gasoline or gasoline vapor, into the atmosphere. When pressure in the fuel tank is below 3 psi (20 kPa), the pressure relief/rollover valves open allowing fuel vapors to flow to the evaporative canister where they are absorbed by a charcoal mixture. This prevents excessive pressure buildup in the fuel system. Most canisters are equipped with a calibrated orifice at the inlet to the canister.

Related Content:

dae woo lanos 02 specs vacum emission hoses, crankcaseventalationhosefor4000gasonangenset, Free 1998 Jeep Service Manual, free download service and repair manual cherokee 1999 year, jeep noise release pressure

2005 TOYOTA TACOMA BULKHEAD INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 10-04-2012

download
STEP 1: INSTALL BULKHEAD ADAPTER ( CONTINUED ) B. Lay Bulkhead Adapter Flange onto the bulkhead (Photo 3) and position the threaded blocks between the knockouts so the holes line up (Photo 4) . Use ¼ – 20 x 1″ counter-sunk screws to secure the Adapter Flange to the bulkhead. STEP 2: INSTALL HOUSING A. Place the Housing Assembly onto the bed rails (Photo 5) . Center it between the rails and leave about ½” of space between the bulkhead and the back of the Housing. Do not fasten the Housing in place. B. Lift the Lid on the Housing and lean it against the cab (Photo 6) . Place a rag between the Lid and cab to prevent scratches. STEP 3: INSTALL TRACKS A. Making sure to leave the Pull Strap connected to the threaded Shipping Stud, rotate the Lock Lever to the 10 o’clock position (Photo 7) . B. Loosely assemble six Track Clamp assem- blies (Photo 8) . Remove the End Caps from the bed rail “C” channels and slide three Track Clamp assemblies into each channel (Photo 9) . Note that the Clamps are labeled “front” , “middle” , and “rear” and must be located accordingly (Photo 10) . Leave the Clamps loose. D. Key the Tracks onto the Housing Stems (Diagram 11), being sure that the Handle is properly engaged into the Tracks and carefully lay the Tracks onto the bed rail (Photo 12) so that the fi n on the underside of each Track seats into the slot in the Clamps (Diagram 13) . E. Use 10 – 24 x ½” truss head screws and Cargo Nuts to secure the Tracks to the Housing Stems (Photo 14) . F. Slide the Clamp assemblies into position so they line up with the double hole patterns located at each end and center of the Track. G. Use 10 – 24 x ½” truss head screws to secure the Clamps to the Tracks (Photo 15) and double check to be sure that Tracks are properly nested into the Clamps. Do not tighten Clamps in place yet and go to step four

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, 1998 Dodge Dakota Service Manual, 2003 s10 airbag wiring diagram, zimmatic pivot wiring, dodge durango 2002 suspension layout, abs and Anti Theft Passive 2000 mercury cougar, free 1997 buick regal gs wiring diagrams, Service manual dodge durano 2002 pdf, 2000 Buick LeSabre Wiring Diagram