Skip to content

fuse panel 2002 buick rendezvous

You search PDF repair manual about fuse panel 2002 buick rendezvous, if there are search results will appear below. If search results do not exist, please search by others keyword.

1994 Ford Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION/ INSTALLATION MANUAL

download
1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron. Fig. 5: Underhood Fuse Panel Identification (1994 -95 Models) Courtesy of FORD MOTOR CO. Fuse & Relay Identification 1 – 15 Amp DRL Module, Foglights 2 – 5 Amp Memory 3 – 20 Amp Ignition Coil 4 – 20 Amp Auto Shock WARNING: Always disconnect battery ground cable before servicing “high-current fuses. It is recommended that “high-current” fuses be replaced by a qualified technician. 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. Virtual Wrench

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

2002 Daewoo Leganza SE Dashboard / Instrument Panel Service and Repair Manual

download
Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the floor console. 3. Remove the sun sensor and the automatic temperature controls assembly. 4. Remove the tweeter speakers and the stereo cassette AM/FM radio. Refer to Section 9F, Audio Systems. 5. Remove the screws and the instrument panel storage compartment. 6. Remove the instrument cluster dimmer switch assembly. 7. Remove the instrument cluster. 8. Remove the chime module. 9. Remove the kick panels. 10. Remove the glove box. 11. Remove the screws and the glove box housing. 12. Disconnect the glove box housing electrical connectors. 13. Remove the knee bolster. 14. Remove the nuts and the bolts securing the steering column. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 2 15. Disconnect the steering column electrical connectors. 16. Lower the steering column. 17. Remove the screw behind the stereo cassette AM/FM radio. 18. Remove the screw securing the instrument panel to the heater air distributor case. 19. Remove the bolts and the glove box brace. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 3 20. Remove the instrument panel screw behind the glove box brace. 21. Remove the instrument panel bolts below the windshield. 22. Remove the bolts securing the bottom of the instrument panel to the floor. 23. Remove the bolts securing the sides of the instrument panel to the body. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 4 24. Disconnect the instrument panel electrical connectors. 25. Remove the instrument panel. Installation Procedure 1. Position the instrument panel in the vehicle. 2. Connect the instrument panel electrical connectors. NOTE: Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion. 3. Install the bolts securing the sides of the instrument panel to the body. Tighten Tighten the instrument panel-to-body bolts to 22 N.m (16 lb-ft) . 4. Install the bolts securing the bottom of the instrument panel to the floor. Tighten Tighten the instrument panel-to-floor bolts to 22 N.m (16 lb-ft) .

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

1998 Ford F 150/250 Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

download
Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. Remove the passenger air bag. For additional information, refer to Section 501-20B . 3. Remove the driver air bag. For additional information, refer to Section 501-20B . 4. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Carefully pry to release the (A) clips and remove the (B) steering column opening cover. 5. Position the electrical connector aside. * Release the push clip from the lower instrument panel steering column cover (044F08). 6. Pull to release the three (A) clips and remove the (B) fuse door. 7. Position the hood latch release handle aside. 1. Remove the screws. 2. Position the hood latch release handle aside. 8. Position the parking brake release handle aside. 1. Remove the screws. 2. Position the parking brake release handle aside. 9. If equipped, remove the instrument panel floor duct panel. * Remove the two push clips and release the expander clip. 10. Remove the lower instrument panel steering column cover (04459). 1. Remove the bolts. 2. Remove the lower instrument panel steering column cover. 11. Remove the LH and RH scuff plates. 12. Remove the LH and RH cowl side trim panels. 13. Disconnect the brake pedal position (BPP) switch electrical connector. 14. Remove the (A) radio ground and the (B) GEM/CTM ground bolts. 15. Disconnect the LH instrument panel main harness connectors. 16. Remove the bulkhead wiring harness electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 17. Remove the bulkhead electrical connector from the dash panel. 1. Release the six locking tabs. 2. Remove the bulkhead connector from the dash panel. 18. Disconnect the air bag diagnostic monitor electrical connectors. 19. Disconnect the inertia fuel shutoff switch electrical connector. 20. Remove the RH ground bolts. 21. Disconnect the RH instrument panel main harness connectors. 22. Disconnect the electronic blend door actuator electrical connector. 23. Disconnect the climate control head vacuum harness connector. 24. Remove the instrument panel steering column opening cover reinforcement (04502). 1. Remove the nuts. 2. Remove the instrument panel steering column opening cover reinforcement. 25. Disconnect the air bag sliding contact electrical connectors and the anti-theft sensor electrical connector.