gm fog light installation instructions

You search PDF repair manual about gm fog light installation instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gm fog light installation instructions Direct Download speed 5432 Kb/s

  gm fog light installation instructions Full Version speed 8172 Kb/s



TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

200-92010 Toyota Camry/ Corolla OE Fit Fog Light Install Instruction

0

Filed Under (Toyota Manuals) by admin on 28-04-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties. 2. Attach the ring terminal with 2 black wires to the 10mm bolt next to the relay 3. Connect the ring terminal from the relay (12v red wire) to the positive terminal of the battery 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector. Seal with 3M Silicone sealant (see picture 1) Picture 1 5. Run the fog light wire harness on the driver side of the car. Use wire ties as needed. 6. Remove dash panels 7. Mount switch into switch knockout on left side of dash 8. From inside the cabin, locate the small connector that were pushed through in step 4. It will be the grommet above the gas pedal 9. Install switch harness 10. T-tap green/black wire from fog light harness to connector E21 pin 11, light green wire (first pin on right). Connector E21 is located on the left side of the steering column (picture 2) Picture 2 11. T-Tap orange/black wire from fog light harness to connector ID pin 3, pink wire (middle third pin from left). Connector ID is left of steering wheel (picture 3) Picture 3 12. Secure with wire ties. 13. Reinstall dash panels 14. Route the fog light wire under car. 15. Remove fog light cover plates and lower splash shields on both sides 16. Insert one side of the fog light into the plastic sleeve and secure other side with supplied Phillip screws (see picture 4

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

2009 HONDA ACCORD 2-DOOR EX, EX-L FOG LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 20-10-2011

download
INSTALLATION 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), and write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the front bulkhead cover (seven clips). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 740220AY FOG LIGHT HARNESS FOG LIGHT HARNESS LEFT FOG LIGHT RIGHT FOG LIGHT LIGHT/TURN SIGNAL SWITCH 742306BE FRONT BUMPER FRONT BULKHEAD COVER 7 CLIPS 4. Remove the front bumper (two self-tapping screws and 10 clips). Have an assistant help you when removing the front bumper. 5. Remove the three self-tapping screws (save for reuse) from the front bumper, and remove the left fog light cover

2009 HONDA CIVIC 2-DOOR EX-L FOG LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 02-10-2011

download
Illustration of Fog Lights Installed on the Vehicle EX-L model 851302AK RELAY SUB HARNESS SWITCH HARNESS COMBINATION LIGHT SWITCH LEFT FOG LIGHT FOG LIGHT HARNESS RIGHT FOG LIGHT 20 A FUSE INSTALLATION 1. Make sure you have the anti-theft codes for the audio system and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. Remove the radiator cover (two expansion clips and two clips). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.

2005 CIVIC 2- AND 4- DOOR FOG LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 20-10-2011

download
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Open the hood and disconnect the negative cable from the battery. Cutting the Front Bumper 3. Remove these parts from the front bumper (four top clips, six bottom clips, two bottom self- tapping screws, and two fender area screws). Remove the front bumper by pulling it out toward you. Place the front bumper on a blanket, to prevent damage while installing the fog lights

Related Content:

2006 isuzu kb300 valvebody teardown diagram

2000-2002 Toyota Celica GTS PowerMax Turbo System Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 19-09-2011

download
installation Please follow the directions below carefully, making sure to perform each step in its listed order. We would like to stress to you that, when the directions call for you to remove or install any of your vehicle’s factory components, you must follow the instructions given in your factory service manual. 1. Remove the bumper cover, fog lights and bumper reinforcement assembly. Also, remove the splashguards and undertray. Note: the fogs lights and bumper reinforcement will not be reinstalled. 2. Drain the engine oil from the oil pan. 3. Remove the airbox. 4. Remove both O2 sensors and exhaust ‘B-pipe’. 5. Remove ‘B-pipe’ heat shield. 6. Remove exhaust manifold’s lower heat shield. 7. Remove the passenger side axle. Keep this unit clean as it will be reinstalled at a later step. 8. Remove the exhaust manifold and upper heat shield. 9. Install the included Exhaust Manifold. 10. Place the included Air Filter Assembly in to its approximate final position. 11. Install the Turbocharger Assembly and then install the air filter onto the turbocharger. 12. Install the Exhaust Manifold Bracket. 13. Reinstall the axle

Related Content:

2000 cellca remove engine, 2000 celica gts engine rebuilding, free 2000 toyota celica gt repair manual

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry