Skip to content

gmc envoy shifter cable

You search PDF repair manual about gmc envoy shifter cable, if there are search results will appear below. If search results do not exist, please search by others keyword.

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Toyota Echo, Toyota Yaris TWM Performance Installation Manual Shifter Cable Bushing Kit

download
1. Working in the engine bay, unscrew the two battery terminals using a ratchet with a 10mm socket. Remove the battery tie-down using a 10mm deep socket for the two bolts. The throttle cable must be removed from the bracket as shown to the left. Take note of how the battery tie down is installed and put it aside for re-installation later.
2. Remove the battery and plastic battery tray from the engine bay. Put them aside in a safe place for re-installation later. 3. Begin removal of the intake by loosening the bolt highlighted to the left with a 10mm socket and a ratchet and disconnect the outlet tube from the air box. Unplug both sensors highlighted on the picture from the air box. Unclip the two latches on the air box. Remove the top part of the air box and air filter to have access to the bottom part of the air box. Put them aside for re-installation later. 4. Remove the three bolts at the bottom of the air box using a 10mm socket and a ratchet with an extension. Put them aside for re-installation later. Unscrew the bolt holding the intake near the driver side headlight using a 10mm socket and a ratchet with an extension. Remove the bottom part of the intake from the engine bay and put it aside for reinstallation later. 6. You now have access to both cable bushings. Remove the cotter hairpins using needle nose pliers. Also remove the metal washers holding down the stock rubber bushings. These washers wildit=aiosp_edit

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Toyota V6 Adapter Plate Installation Manual

download
Apply silicone to face of single or dual transfer case assembly. Install adapter plate on face of transfer case, using 4 M10-1.25×35 bolts (provided). We recommend applying blue LocTite® to threads before installation. Torque four plate bolts to 30 ft. lbs. Step 2 Install M-10-1.25×30 allen head bolt using blue Loc- Tite® torque to 30 ft. lbs. Step 3 Remove rear transmission seal using a seal remover or claw hammer. Step 4 Step 5 Install M-10-1.25x 35 bolt using blue LocTite® torque to 30 ft. lbs. Using degreaser, clean the rear transmission seal sur- face. Step 6
Ensure two dowels are in place in the transmission. If dowels are in the transfer case move them to the trans- mission. Step 8 Step 11: Apply silicone to rear face of transmission Slide coupler into place on the back of the transmis- sion. Step 7 Step 9 Step 10 Apply silicon to smaller end of seal adapter Install Seal Adapter into rear of transmission. Gently seat seal adapter into place using rubber mallet Step 11 After Assembling Adapter Plate & T/Case(s): Install replacement v6 dual transfer case crossmember Reconnect 4 wheel drive indicator (This may require cutting and splicing connector from original case) 1988-1991 Application, reconnect speedometer cable (Use speedometer extension cable for dual case applications) 1992-1995 Application will need a replacement VSS for the transfer case Reattach front and rear drive shafts (drive shaft lengths may need to be changed) Fill transfer case with 90W GL5 gear oil, check gear oil level in transmission Reinstall transfer case shifter and boot Drain and replace transfer case oil after first 1,000 miles and every 30,000 thereafter Full synthetic gear oil may be used. Step 12 Using 6 of the 9 stock bolts, 1 allen head bolt and 2 M10-1.25×35 bolts, attach transfer case to transmission. Use blue LocTite® on all bolts. Tighten bolts to 30 ft. lbs. The second allen head bolt should be installed in position shown on the upper right (passenger) side. Step 13 These instructions are designed as a general installation guide. Installation of many Trail-Gear Products require specialized skills such as metal fabrication, welding and mechanical trouble shooting. If you have any questions or are unsure about how to proceed, please contact our shop at 559-252-4950 or seek help from a competent fabricator. Using fabrication tools such as welders, torches and grinders can cause serious bodily harm and death. Please operate equipment carefully and observe proper safety procedures. Rock crawling and off-road driving are inherently dangerous activities. Some modifications will adversely affect the on-road handling characteristics of your vehicle. All products sold by Trail-Gear Inc are sold for off road use only. Any other use or application is the responsibility of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may under certain circumstances void your original dealer warranty. Modification of your vehicle may create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or death. Buyers and users of these products hereby expressly assume all risks associated with any such modifications and use.

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything