guest battery isolator wiring diagram model

You search PDF repair manual about guest battery isolator wiring diagram model, if there are search results will appear below. If search results do not exist, please search by others keyword.



  guest battery isolator wiring diagram model Direct Download speed 5432 Kb/s

  guest battery isolator wiring diagram model Full Version speed 8172 Kb/s



2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 2003 s10 airbag wiring diagram, abs and Anti Theft Passive 2000 mercury cougar, 1998 Dodge Dakota Service Manual, dodge durango 2002 suspension layout, zimmatic pivot wiring, troubleshooting front blower motor resistor in a 2005 dodge durango, 97 buick riviera Ignition Switch Diagram

1999 Chrysler LHS V6-3.5L VIN G Battery Replacement Manual

0

Filed Under (Chrysler Manuals) by admin on 24-06-2012

download
Battery Replacement Notes WARNING: TO PROTECT THE HANDS FROM BATTERY ACID, A SUITABLE PAIR OF HEAVY DUTY RUBBER GLOVES, NOT THE HOUSEHOLD TYPE, SHOULD BE WORN WHEN REMOVING OR SERVICING A BATTERY. SAFETY GLASSES ALSO SHOULD BE WORN . REMOVAL 1. Turn the steering wheel all the way to the right. 2. Verify that the ignition switch and all accessories are OFF. 3. Disconnect and isolate the negative battery cable remote terminal from the remote battery post. 4. Remove air cleaner housing. 5. Remove battery splash shield. 6. Remove two short bolts to battery hold down. 7. Slide battery rearward to disconnect the negative and positive battery terminals from battery. 8. Slide battery toward rear of vehicle and lift out through wheel well opening. 9. Remove battery from vehicle. 1. Tighten clamp nuts to 8.5 N.m (75 in. lbs.) torque.INSTALLATION For installation, reverse the above procedures. Inspect and clean battery and attaching components before installation. WARNING: DO NOT OVER TIGHTEN BATTERY CABLE CLAMPS, DAMAGE TO CLAMPS CAN RESULT .

Related Content:

where is the battery located on a dodge journey 2010, what size battery for a 1997 buick regal, NOCO Battery Isolator Instructions, how to remove battery chevy cruze, how to charge battery in 2012 chevy equinox, battery location 2013 dodge journey, 2012 honda crv heavy duty battery, 2012 Dodge Avenger Battery, 2003 hummer battery drain, 01 evony battery drain test light

Ford Sierra Service and Repair Manual Download

0

Filed Under (Ford Manuals) by admin on 20-05-2012

download
Puddles on the garage floor or drive, or obvious wetness under the bonnet or underneath the car, suggest a leak that needs investigating. It can sometimes be difficult to decide where the leak is coming from, especially if the engine bay is very dirty already. Leaking oil or fluid can also be blown rearwards by the passage of air under the car, giving a false impression of where the problem lies. Warning: Most automotive oils and fluids are poisonous. Wash them off skin, and change out of contaminated clothing, without delay. Identifying leaks The smell of a fluid leaking from the car may provide a clue to what’s leaking. Some fluids are distinctively coloured. It may help to clean the car carefully and to park it over some clean paper overnight as an aid to locating the source of the leak. Remember that some leaks may only occur while the engine is running. Sump oil Gearbox oil Brake fluid Power steering fluid Oil from filter Antifreeze Engine oil may leak from the drain plug… …or from the base of the oil filter. Leaking antifreeze often leaves a crystalline deposit like this. Gearbox oil can leak from the seals at the inboard ends of the driveshafts. A leak occurring at a wheel is almost certainly brake fluid. Power steering fluid may leak from the pipe connectors on the steering rack. 0•9 Roadside repairs When jump-starting a car using a booster battery, observe the following precautions: ? Before connecting the booster battery, make sure that the ignition is switched off. ? Ensure that all electrical equipment (lights, heater, wipers, etc) is switched off. ? Make sure that the booster battery is the same voltage as the discharged one in the vehicle. ? If the battery is being jump-started from the battery in another vehicle, the two vehcles MUST NOT TOUCH each other. ? Make sure that the transmission is in neutral (or PARK, in the case of automatic transmission). Jump starting will get you out of trouble, but you must correct whatever made the battery go flat in the first place. There are three possibilities: 1 The battery has been drained by repeated attempts to start, or by leaving the lights on. 2 The charging system is not working properly (alternator drivebelt slack or broken, alternator wiring fault or alternator itself faulty). 3 The battery itself is at fault (electrolyte low, or battery worn out). Connect one end of the red jump lead to the positive (+) terminal of the flat battery Connect the other end of the red lead to the positive (+) terminal of the booster battery. Connect one end of the black jump lead to the negative (-) terminal of the booster battery Connect the other end of the black jump lead to a bolt or bracket on the engine block, well away from the battery, on the vehicle to be started. 1 2 3 4 Make sure that the jump leads will not come into contact with the fan, drive- belts or other moving parts of the engine. 5 Start the engine using the booster battery, then with the engine running at idle speed, disconnect the jump leads in the reverse order of connection

Related Content:

2005 ford escape battery drain, ac leaking in chevy trailblazer, antifreeze for a 2013 chevy cruze, chevy cruze coolant leak

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 16-01-2012

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

Related Content:

020139007 service bulletin, battery restoration procedure, servicing a battery module honda insight

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 06-02-2012

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

Related Content:

IDLE RELEARN 02 CAMRY, 04 rav4 idle at 6000 rpm after battry change, 2001 malibu throttle position sensor relearn procedure, 2006 cheverolet impala will not idle, 2008 dodge grand caravan coolant fan runs continuasly, dodge caravan1997 transm autom 3 3l how connected with radiator, Dodge Cruise Control Repair 2012 caravan, IRRATIC IDLING 87 2 8 V6 BLAZER

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, PIN DATA 2005 скачать, what pins are positve and negative on a 40 pin cat ecm

1992 Toyota Cressida Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 30-11-2011

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

Related Content:

toyota matrix ecu diagram, ECU power steering module diagram 2009 Toyota Matrix

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, 2007 chevy silverado brake switch installation, what causes 2005 toyota sienna starter relay to burn out, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, ignition switch removal on 2003 buick century, ignition switch wiring diagram 2006 chevrolet uplander, no power between starter and ignition uplander, relay system in a 2002 buick centry

Toyota Landcruiser / Scout Weatherproof Harness Wire Harness Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-03-2012

download
Grounding the Automobile A perfectly and beautifully wired automobile will nevertheless have bugs and problems if everything is not properly grounded. Do not go to the careful effort of installing a quality wire harness only to neglect proper grounding. Note: The Painless Wire Harness Kit includes no ground wire except the black wire from the two headlamp connectors. You must supply ground wire (14-16 gauge) for all circuits. 6.3.1 Connect a Ground Strap or Cable (2-gauge minimum) from the Negative Battery terminal to the automobile chassis (frame). 6.3.2 Connect a Ground Strap from the Engine to the chassis (even a 10-gauge wire is too small) . DO NOT RELY UPON THE MOTOR MOUNTS TO MAKE THIS CONNECTION . 6.3.3 Connect a Ground Strap from the Engine to the Body. 6.3.4 If you have a fiberglass body you should install a terminal block to ground all your Gauges and Accessories. Ground the Terminal Block with at least a 12-gauge wire to the chassis. 6.4 Terminal Installation and Making Connections Note: In the following steps you will be making the circuit connections. Before you start, you should carefully read Sections 7.0 through 10.0 , as appropriate, and continually refer to Section 10.0 , DOUBLE- CHECKING your routing and length calculations before cutting any wires and making connections. Give special attention to Turn Signal and Ignition Switch connections. These can be somewhat confusing. 6.4.1 Have all needed tools and connectors handy. 6.4.2 Select the correct size terminal for the wire and stud application. 6.4.3 Determine the correct wire length and cut the wire. Remember to allow enough slack in the harness and wires at places where movement could possibly occur, such as automobile body to frame, frame to engine, etc. Double-check your calculations. 6.4.4 Strip insulation away from wire. Strip only enough necessary for the type of terminal lug you are using. Note: In the following step, make sure that the terminal is crimped with the proper die in the crimping tool. An improper crimp will NOT make a good connection. 6.4.5 Crimp the terminal onto the wire. CAUTION: DO NOT OVER-CRIMP! 6.4.6 Connecting the harness throughout the groups is a redundant process. Make sure that each wire is FIRST properly routed and THEN attach. DO NOT ATTACH FIRST THEN ROUTE AFTERWARD. 6.4.7 When all wires are attached, tighten the mounts and ties to secure harness permanently. 6.5 Testing The System 6.5.1 Use a small (10 amp or less) battery charger to power up the vehicle for circuit testing. If there is a problem anywhere, the battery charger’s low amperage and internal circuit breaker will provide circuit protection. CAUTION: IF YOU HAVE NOT YET DISCONNECTED THE BATTERY FROM THE AUTOMOBILE, DO SO NOW! DO NOT CONNECT THE BATTERY CHARGER WITH THE BATTERY CONNECTED. Connect the battery charger’s NEGATIVE output to the automobile chassis or engine block and its POSITIVE output to the automobile’s positive battery terminal. 6.5.2 INDIVIDUALLY turn on each light, ignition, wiper circuit, etc. and check for proper operation. Note: The turn signals will not flash properly if you do not have both the front and rear bulbs installed and connected. 6.5.3 When all circuits check out THEN attach the battery cable to the battery for vehicle operation

Related Content:

where are the battery terrminals on a 2012 pruis, 1996 ford f53 chassis circuit board diagram, 1996 ford F53 wiring diagrams, 97 cadillac deville ground location, FORD E-450 FUEL PUMP WIRING

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

wire diagram on a 2002 grand prix headlight, 1998 jimmy fuel pump install, 03 ford windstar fuel pump wiring, vcm ground wire, pontiac grand am fuel pump wireing harness replacement instructions, proper connection for horn relay 1968 chevelle, 2005 tundra speed pulse signal wire location, fan cable for 1998 dodge caravan, location of vent valve solenoid on 2010 ford ranger, 86 corvette wiring schematics

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, free 1997 buick regal gs wiring diagrams, 2003 s10 airbag wiring diagram, abs and Anti Theft Passive 2000 mercury cougar, 1998 Dodge Dakota Service Manual, dodge durango 2002 suspension layout, zimmatic pivot wiring, troubleshooting front blower motor resistor in a 2005 dodge durango, 97 buick riviera Ignition Switch Diagram