handbrake adjustment on mitsubishi canter

You search PDF repair manual about handbrake adjustment on mitsubishi canter, if there are search results will appear below. If search results do not exist, please search by others keyword.



  handbrake adjustment on mitsubishi canter Direct Download speed 5432 Kb/s

  handbrake adjustment on mitsubishi canter Full Version speed 8172 Kb/s



2004 Mitsubishi Lancer O-Z Rally TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 06-06-2012

download
Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.

Related Content:

2005 mazda 3 2 3l push rod clearance, manual book 1G FE throtle sensor, p2263 mitsubishi canter

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, montero crank shaft pully removal, montero xls bleeding cooling system how, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero

1997 Jeep Cherokee 2WD Serpentine Belt INSPECTION ADJUSTMENT REMOVAL And INSTALLATION

0

Filed Under (Jeep Manuals) by admin on 05-01-2012

download
INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure. Loosen the pump upper pivot bolt, lower locknut and pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 1. Use a belt tension gauge placed in the middle of the belt being tested. Proper tension for a new belt is 180-200 lbs. (800-900 N) and 140-160 lbs. (623-712 N) for a used belt. 2. Tighten the pump adjusting bolt to achieve proper tension and recheck the belt tension. 3. Fig. Fig. 1: Loosen the pivot bolt (1), then the locking bolt (2) to loosen the power steering pump from behind Fig. Fig. 2: Use a ratchet and 13mm size socket to rotate the power steering pump Fig. Fig. 3: Adjustment points on the 2.5L engines without power steering (rear view) Fig. Fig. 4: Adjustment points on the 2.5L engine (front view) Removal & Installation 2.5L and 4.0L Engines With Power Steering See Figures 5, 6 and 7 Fig. Fig. 5: Proper belt routing diagram can usually be found on a sticker located in the engine compartment Fig. Fig. 6: Common 4.0L engine serpentine belt routing Fig. Fig. 7: Common 2.5L engine serpentine belt routing Loosen the rear power steering pump mounting bolts using a ratchet and 13mm socket or a 13mm box wrench. 1. Loosen the pump upper pivot bolt, lower locknut and the pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 2. Remove the belt. 3. To install: Install the belt. 4. Tighten the pump adjusting bolt to achieve proper tension. 5. Install the pump rear mounting bolts, pivot bolt and locknut. Tighten the bolts to 20. ft. lbs. (27 Nm). 6. Check the belt for proper tension. If tension is incorrect, refer to the adjustment procedure in this section. 7. 5.2L and 5.9L Engines See Figures 8, 9 and 10

Related Content:

1986 jeep cherokee serpentine belt route, serpintin belt diagram for 2006 jetta, kia 3 5 crank bolt for sale, jetta 2006 fan belt totation, GM 10 Bolt Rebuild Manual, gm 10 bolt instructions, 99 Jeep Cherokee Owners Manual pdf, 2010 Kia Forte Serpentine Routing Belt Diagram, 2004 honda civic serpentine belt, 1995 Jeep 2 5L ccv orfice and emissions

Toyota Landcruiser Rear Brake Upgrade Package / Installation Manual

0

Filed Under (Toyota Manuals) by admin on 23-03-2012

download
Toyota Landcruiser Rear Brake Upgrade Package HOPPERS STOPPERS HOPPERS STOPPERS HOPPERS STOPPERS HOPPERS STOPPERS 4 4 4 4 Rear Brake Upgrade Package 78/79 Series Toyota Landcruiser Cause of Rear Brake Problems 1 Combining a drum handbrake and a disc rotor and caliper within the confines of a 16-inch wheel necessitates a small brake caliper and small pad radial section, resulting in an undersized pad area. The standard design has a thin disc and a handbrake of small diameter and swept area relative to the weight of the vehicle. 2 The backing plate and handbrake arrangement allow mud and slurry to enter but not exit, causing abrasives to accumulate and rapidly destroy the handbrake, including its function as an emergency brake. 3 The small disc pad contact area is at odds with the affects of loading under abrasive conditions where rates of wear are parabolic for wear rate versus load. 4 The handbrake design is fiddly and complicated with many small parts that prove to be difficult to assemble correctly. Hoppers Stoppers design solution There appear to be a few possible ways to approach this problem, with a couple of companies proposing designs. Some take unconventional and unusual approaches but appear expensive to purchase and repair; with their application probably only justified if they perform perfectly for a very long time. Hoppers Stoppers’ approach is to stick to proven principles and overcome the basic weakness of the existing design. By all reports, the front brakes on these Toyotas work adequately, and considering their environment do not give significant problems in the field. In our view these brakes are not particularly special in their engineering, just the same basic front brakes that they have made for many years. If we built a rear brake set as solid and even better designed than the front it should last as long. This requires a big, thick disc rotor and brake lining swept area similar to the front

1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Timing Belt: Service and Repair Manual

0

Filed Under (Mitsubishi Manuals) by admin on 23-01-2011

download
.Removal of crankshaft pulley. Using special tools remove the crankshaft pulley from the crankshaft. CAUTION: -Use only the specified special tools, or a damaged pulley damper could result. 10.Removal of engine support bracket. Remove the engine support bracket in the numbered sequence shown in the illustration. Spraying lubricant, slowly remove the bolt (reamer bolt) indicated by the arrow. CAUTION: -Keep in mind that the reamer bolt is sometimes heat seized on the engine support bracket. 12.Removal of timing belt. (a)Align the timing marks.
1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 3 (b)Make a mark on the back of the timing belt indicating the direction of rotation so it may be reassembled in the same direction it it is to be reused. (c)Loosen the center bolt on the tensioner pulley to remove the timing belt. CAUTION: -Water or oil on the belt shorten its life drastically, so the removed timing belt, sprocket, and tensioner must be free from oil and water. These parts should not be washed. Replace parts if seriously contaminated. If there is oil or water on each part check the front case oil seals, camshaft oil seal and water pump for leaks. 1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 13.Installation of auto tensioner. (a)If the auto tensioner rod is in its fully extended position, reset it as follows:1993 Mitsubishi 3000GT V6-2972cc 3.0L DOHC 8.80 Page 5 1)Keep the auto tensioner level and, in that position. clamp it in the vise with soft jaws. 2)Push in the rod little by little with the vise until the set hole (A) in the rod is aligned with that (B) in the cylinder. CAUTION: -Push in the rod slowly to prevent the push rod from being damaged. 3)Insert a wire [1.4 mm (0.055 in.) in diameter] into the set holes. 4)Unclamp the auto tensioner from the vise. (b)Install the auto tensioner. CAUTION: -Leave the wire installed in the auto tensioner. 12.Installation of timing belt. (a)Align the timing marks on the respective sprockets. In case of the camshaft sprockets in the front bank, proceed as follows: 1)Install the crankshaft pulley. Shift the timing mark on the crankshaft sprocket by three teeth to lower the piston in No. 1 cylinder slightly from the top dead center on compression stroke. CAUTION: -Turning the camshaft sprocket with the piston in No.1 cylinder located at TDC on compression stroke may cause the valves to interfere with the piston

Related Content:

case 446 repair manual, 1993 bmw 525i owners manual, 1993 corvette vats, 1993 infiniti g20 repair manual, Free Mitsubishi 3000GT Repair Manual, remove optic park in 93 vette, removing camshaft sprocket 3000 gt, renew vss sensor, video of oil pump install for 3000gt

1995 Mazda MX-6 FRONT DISC BRAKE PADS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mazda Manuals) by admin on 16-02-2012

download
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. Fig. 2: Exploded View Of Front Brake Disc Assembly Courtesy of MAZDA MOTORS CORP. MINIMUM PAD LINING SPECIFICATIONS (FRONT) Application Thickness In. (mm) MX-6, 626 FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove front disc brake caliper with brake hose connected. See FRONT DISC BRAKE CALIPER . Wire caliper aside. Remove rotor-to-hub screws (if equipped). Remove rotor. 2. Machine rotor if lateral runout exceeds specification. Replace rotor if measured thickness is less than specified minimum thickness. See DISC BRAKE SPECIFICATIONS table. To install, reverse removal procedure. REAR DISC BRAKE PADS Removal & Installation 1. Raise and support rear of vehicle. Remove rear wheel assemblies. Release parking brake and disconnect parking brake cable from caliper. Remove manual adjustment gear concealment plug from caliper. See Fig. 3 . Insert an appropriate size Allen wrench through hole and turn manual adjustment gear counterclockwise to retract caliper piston. 2. Remove upper guide bolt from caliper. Rotate caliper downward and support using wire. Remove “M” springs. Remove pads, shims and guide plates. Replace pad if lining thickness is less than .04″ (1.0 mm). 3. To install, reverse removal procedure. Turn manual adjustment gear clockwise until brake pads slightly touch rotor. Turn manual adjustment gear back 1/3 turn.

Related Content:

2007 chevy tahoe min disc thickness after machining, 95 chevy monte carle front brake rotor minimum thickness, Minimum Rotor Thickness Spec Sheet, pontiac pursuit parking brake cable, minuem roter tickness, minimum rotor thickness for chrysler pacifica, min spec for 2008 mada brake rotor thickness, mimimum rotor thickness for a 2000 chrysler sebring, mazda 626 pin size brake pads, how do i replace the rear brake caliper guide pin on a 2005 kia spectra

2007-Up Toyota Tundra 2WD/4WD ADJUSTABLE UPPER STRUT FRONT LIFT/ LEVELING KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Step 1: Measure current front ride height. Take a measurement from the bottom of the wheel/rim to the lip of the fender on each side of the vehicle. Write down measurements to help in determining ride height after new kit is installed. (Figure A) Step 2: Position vehicle on a flat surface or automotive lift. Suspend front wheels , lifting by the frame with a floor jack or lift jack. Secure using jack stands and wheel chocks. Be sure engine is turned OFF and vehicle is in PARK. Remove tire/wheel assembly on ONE side of vehicle . Step 3: Support Spindle to protect ABS system and brake lines! LOOSEN, but don’t completely remove upper ball joint nut, outer tie rod nut and sway bar link nut at the lower control arm. Step 4 : Break Outer tie rod and ball joint from their tapers using tools specific to this procedure. CAREFULLY, while supporting the spindle assembly, completely remove upper ball joint nut & tie rod nut, leaving the loosened sway bar link nut in place. ( Figure B) Step 5: Remove strut assembly from the vehicle. Remove LOWER strut bolt first, followed by the three (3) upper strut nuts. CAUTION! BE EXTREMELY CAREFULL TO SUPPORT STRUT ASSEMBLY WHEN REMOVING UPPER STRUT NUTS! The Strut/Spring assembly is heavy and can cause injury to technician or damage to other components if released too quickly! (Figure C) Step 6: Apply 50% of the INCLUDED Synthetic Grease to the TOP of the THREADED INNER ADJUSTMENT SCREW, as illustrated. (Figure D) Step 7: Using the original OEM stud nuts , secure new Adjustable Upper Strut Kit to OEM upper strut studs and torque to manufacturer’s specifications. (Figure E) IMPORTANT! Be sure the Threaded Adjustment Screw Rotates FREELY after securing kit to OEM top of strut! If not, slightly loosen the three upper stud nuts and reposition Threaded Adjuster Screw UPWARD slightly. Retorque upper stud nuts to manufacturer’s specifications and recheck that Inner Adjuster Screw rotates freely. Step 8: Install the Top Connection Plate ONLY, studs directed UPWARD, into position in the strut tower, and secure with the NEW Nylock stud nuts supplied with this kit. Torque stud nuts to OEM specifications. (Figure F) Step 9: Reinstall strut assembly . Be sure the new Adjustable Upper Strut Kit is THREADED DOWN in the MOST COMPACT POSITION for easiest reassembly, then pass exposed threaded area of the kit THROUGH the center of the Top Connection Plate already installed. HINT: The use of a pry bar or breaker bar may simplify reinstallation of the Strut Assembly. (Figure G) Step 10: Install Large 1-1/4-12 Adjustment Locking Jam Nut included with this kit and tighten until snug to Top Connection Plate. Install Snap Ring included with kit.

EDELBROCK ROLLER ROCKER ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 21-02-2012

download
INSTALLATION: Rotate the main trunnion of the rocker arm so that the flat machined surface is facing up, then lower the rocker arm onto the rocker stud so that the roller tip is contacting the valve and the pushrod is seated into the cup. Rotate the engine by hand until cylinder #1 is at TDC on the compression stroke (the rotor on the distributor should be lined up with cylinder #1′s spark tower). If you are using hydraulic lifters, rotate the pushrod between your fingers as you tighten the rocker arm adjustment nut, once you start to feel drag in the pushrod you are at zero lash. Continue tightening the adjustment to set the lifter preload according to your camshaft installation instructions, then use an allen wrench to tighten the posi-lock. If you are using mechanical lifters, use a feeler gauge while tightening the adjustment nut to set your valve lash to the clearance listed in the camshaft installation instructions, then use an allen tool to tighten down the posi-lock. Complete this procedure for both the intake and exhaust rockers, then rotate the crankshaft 90° and repeat this procedure on the next cylinder in the firing order. Continue doing so until all 16 rocker arms have been properly installed and adjusted. Proper operation can be verified by rotating the crank by hand and observing the motion of the pushrod and the position of the roller on the valve tip. The pushrods must never contact the cylinder head walls and the roller tip must maintain at least 50% contact with the valve tip during a full rotation of the camshaft. If the pushrod contacts the cylinder head or the roller fails to maintain sufficient contact with the valve tip you will need to loosen your rocker stud and adjust your pushrod guideplate until proper valvetrain alignment is achieved.

Renault Laguna II A195 Door function control module driver

0

Filed Under (Renault Manuals) by admin on 13-01-2012

download
Battery – 30 Battery + A195 Door function control module, driver A196 Door function control module, passenger M27 Door mirror adjustment motor, driver M28 Door mirror adjustment motor, passenger S98 Door mirror adjustment switch EP10Earth point location 10 EP4 Earth point location 4 EP5 Earth point location 5 EP9 Earth point location 9 M14 Electric window motor, driver M15 Electric window motor, passenger S64 Electric window switch, driver’s door S65 Electric window switch, passenger door F Fuse X28-IIFuse box/relay plate, engine bay X28-IFuse box/relay plate, fascia 1 K79 Ignition main circuits relay 15 Ignition switch – ignition ON A11 Multifunction control module X92 Shorting link connector bl = blue br = brown el = cream ge = yellow gn = green gr = grey nf = neutral og = orange rs = pink rt = red sw = black vi = violet ws = white hbl = light bluehgn = light green rbr = maroon x = braided cabley = high tensionz = non-cable connection NOTE: In certain diagrams (Citroen, Peugeot & Renault), colour codes are replaced by numbers which are used to identify a particular cable and not the colour. In this instance, the cables will be numbered at each end close to the harness connector.

Related Content:

renault laguna no ingntion, renault laguna relays

2002 BMW M3 Coupe A/T – SMG Transmission Clutch Does Not Engage Repair Manual

0

Filed Under (Bmw Manuals) by admin on 17-06-2012

download
SITUATION Gear indicator in instrument cluster flashes while driving, or, when stationary, gear can be selected, but clutch does not engage, and indicator flashes. CAUSE “Hood closed” status is not recognized by SMG control module because one or both hood latch micro switches are not functioning properly. 1. If ONE of the micro switches has failed, it is possible to drive off, but gear indicator in instrument cluster will flash. 2. If BOTH micro switches have failed, gear can be selected but clutch will not engage and gear indicator in instrument cluster will flash. The micro switch failure could be caused by damage during assembly, or incorrect adjustment. Another possible cause is improper handling of the micro switches during a workshop visit. In the workshop, care should be taken to ensure that no tools are pushed into the lower hood latch assemblies as the switching element on the micro switch could be bent or damaged. The opening must not be used for holding tools! CORRECTION On a customer complaint basis, check function of both hood latch micro switches using DISplus or GT1. Replace faulty lower/lower hood latch assembly, or correct hood adjustment as needed. Adjustment procedure and specifications can be found in Repair Instructions 41 61 014. PROCEDURE During diagnosis, the switching element of the lower must not be pressed too hard (illustration shows internal view of hood latch assembly). Illustration shows a bent switching element Illustration shows an intact micro switch. PARTS INFORMATION

Related Content:

2005 mazda 3 2 3l push rod clearance, manual book 1G FE throtle sensor, p2263 mitsubishi canter