heater control valve 2004 nissan quest

You search PDF repair manual about heater control valve 2004 nissan quest, if there are search results will appear below. If search results do not exist, please search by others keyword.



  heater control valve 2004 nissan quest Direct Download speed 5432 Kb/s

  heater control valve 2004 nissan quest Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, 2008 hyundai elantra purge valve, c230 2005 removing pcv valve and hoses, clean egr valve lincoln, where is the pcv valve on chevy cruze, where is the pvc valve located on a 2008 toyota tundra, 2007 implala vent solenoid replacement, egr valve chevy trailblaxer 2005, fuel purge valve for 2006 chevy impala, pvc valve for 2001 merc sable 24 valve overhead cam

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB

Related Content:

toyota 4af valve clearance, how to replace the perge valve on a Saturn Vue, perodua kancil valve clearen instraction pdf, REPAIR MANUAL FOR KANCIL ENGINE PDF, yhs-ddc_bd, lifter replacement 2004 avalanche 5 3 engine, 4m51 engine valve clearance, 2012 chevy cruze pcv valve, 2010 Honda Accord valve cover Torque Specs, 2006 toyota tacoma 4 cyl valve cover gasket replacement

2008 Ford Focus A/T Main Control Valve Body Removal And Installation

0

Filed Under (Ford Manuals) by admin on 01-07-2012

download
Disassembly 12 7Z490 Separator plate and gasket assembly 1. Remove the solenoid body bolts and the 13 7A101 Body — control valve lower solenoid body. 14 7R294 Stop — main regulator valve 15 7F445 Retainer plate — main regulator valve 16 7A270 Spring — main fluid pressure regulator valve 17 7C338 Valve — main fluid pressure regulator 18 7G411 Spring — solenoid regulator valve 19 7H392 Valve — solenoid regulator valve 20 7D400 Spring — intermediate servo accumulator 21 7D398 Piston — intermediate servo 2. Remove and discard the solenoid body gaskets. accumulator 22 7G408 Valve — converter pressure relief 23 7G316 Spring — converter regulator valve 24 7M040 Valve — lock up control 25 7Z490 Gasket — solenoid body 26 7G179 Valve — low reverse shift 27 7M040 Valve — 3-4 shift 28 7H148 Shift Solenoid B (SSB) (on/off) valve 29 7H148 Shift Solenoid A (SSA) (on/off) valve ISASSEMBLY AND ASSEMBLY (Continued) 3. Remove and discard the seals. 3. Install the seals. 4. Disassemble the main control valve body. 4. Install a new solenoid body gasket. Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Tighten to 9 Nm (80 lb-in)

Related Content:

5R55E Valve Body manual, diagram for torque converter clutch for 2000 Venture, valve body torque specs chevy venture, how to chane the vent valve solenoid in 2008 gmc yukon, 2007 torqshift valvebody removal, how to change the vent valve seliod on a 2008 gmc, 2003 trailblazer valve body, exploded view toyota A650E valve body, free 5r55e valve body transmission gasket replacement instructions for 2001 ford explorer, how to remove sl2 bellhousing without removing valve body

Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System OPERATION MANUAL

0

Filed Under (Honda Manuals) by admin on 28-01-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines
SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum.

DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

0

Filed Under (Toyota Manuals) by admin on 11-04-2012

download
Tighten Tighten the bracket mounting bolt to 12 N?m (106 lb in). Connect the vent valve pipe to the EVAP canister. • Install the two vent valve pipe clips into the existing underbody holes. • Connect the EVAP canister vent valve electrical connector, if equipped. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. • Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward. • Raise the transmission and reinstall the transmission support. • Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch*points and heat sources. • Lower the vehicle. • 2004-2007 Model Year (Use Service Kit P/N 19152349) Raise the vehicle. Suitably support the vehicle. • Disconnect the EVAP canister vent valve electrical connector. • Disconnect the canister pipe from the vent valve. • Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. • Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end. Crew Cab Short Box Shown Below, Other Configurations Similar Extended Cab Short Box Shown Below, Other Configurations Similar Install the new canister vent valve to the fuel tank clip or mounting bracket. • Cut bulk 5/8″ heater hose to a length of approximately 76 mm (3 in). Install the hose between the vent valve and the canister pipe and secure using clamps. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. •

Related Content:

need to replace vent valve solenoid on 2005 chevy uplander, how to remove evap canister 2007 pontiac montana, how to replace evap canister purge solenoid valve 2001 pontiac montana, 2006 pontiac g6 gt evap vent part number, location of vent control valve on 1998 lexus es300, chevy uplander evap solenoid, 2004-2006 Volvo XC90 2 5T Crankcase Ventilation Hose [OEM], 2010dodge ram 1500 ac vent diagram, where to locate a vent canister solenoid on a 2007 pontiac torrent, Gas tank valve evap for c6 corvette

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 1995 accord repair manual pdf, 2003 buick lesabre lose power for instrument panel and a/c controls, 1989 corvette climate control panel, 2005 honda crv malfunction indicator lamp reset, honda accord 61-10 code, honda accord code 61-1, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord cooling fans

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

0

Filed Under (Ford Manuals) by admin on 20-04-2012

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

Related Content:

can a 2002 taurus transmission be removed without removing subframe, CLEAN THROTTLE BODY CHEVY ENVOY, how to replace the bumper cover on a 1998 Isuzu Rodeo, 03 Chevy impala removing valve cover, volvo xc90 2 9 rocker cover removal, valve cover gaskets on 2002 Escape V6, Removing Valvebody on 722 6, remove 2003 taurus transmission lowering only one side subframe, how to removed a valve body from volvo s 70, how to remove valve cover 5 4 32v navigator

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

1984-1995 Honda Accord/Prelude In­Tank Fuel Pumps TEST/REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 03-07-2012

download
Carbureted Fuel System GENERAL INFORMATION On these vehicles, the engine management system is considered part of the emission control system. The major components include the carburetor(s), feedback control system, the air injection system, a throttle control system and the EGR system. The system consists of sensors and switches that feed information to the Electronic Control Unit (ECU), which will then operate several solenoid valves to maintain the ideal air/fuel ratio under all conditions. As useful as the tests found in this section are, the first step in repair or service to engine management systems is still to gain as much information as possible about the problem; when and under what conditions it occurs. At highway speed? At idle only? Only under heavy load or hard acceleration? Wet weather? Defining the problem will eliminate many systems from consideration and possibly point to the affected system. Before diving into an extended electrical diagnosis, take the time to review the basics. Check every vacuum line for cracks or leaks. Check every electrical connector for corrosion or loose pins. Quite often, simply unplugging and reconnecting a connector will break up corrosion on the pins and restore the circuit. Watch out for poor grounds, particularly if the car has experienced major bodywork. COMPONENT TESTING Air Injection System The purpose of this system is to supply oxygen to the exhaust stream at a point in the exhaust manifold that is hot enough to burn off some of the hydrocarbon emissions. The main component is an air suction valve. The valve is spring loaded to stay closed, with engine vacuum supplied to a diaphragm that reduces the spring pressure and allows the reeds to open. The ECU regulates the engine vacuum to the diaphragm by operating a solenoid valve. 1. With the engine at normal operating temperature and at idle, remove the air cleaner and listen for a bubbling sound at the air suction port. There should be no sound at idle, meaning the air suction valve is closed. 2. If the noise is heard at the air suction port, disconnect the vacuum hose at the air suction valve and connect a vacuum gauge to the hose. There should be no vacuum. If there is vacuum and the noise stops, the problem is in the control system. If there is no vacuum and the bubbling sound is still there, the air suction valve is defective and must be replaced. 3. To test the valve, draw a vacuum at the air suction valve diaphragm and listen for a bubbling sound at the air suction port. If no sound is heard, the air suction valve or diaphragm is faulty. Throttle Control System

Related Content:

Honda Automotive Electrical Connectors Replacement

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram