heater motor 04 bonneville

You search PDF repair manual about heater motor 04 bonneville, if there are search results will appear below. If search results do not exist, please search by others keyword.



  heater motor 04 bonneville Direct Download speed 5432 Kb/s

  heater motor 04 bonneville Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

mitsubishi canter (4D35) repair manual pdf, starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 27-02-2011

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

Related Content:

replace 2002 suburban fan motor, what screws are used to install a lacrosse blower resistor, 2004 cavalier stepper motors, hino blower motor replace procedure, installing heaterfan motor dodge grand caravan 2011, instructions for replacing 2004 pontiac grand prix blower motor, is the resisistor built in the blower motor on a 2012 chevy sonic?, remove heat blower motor 67 grand prix, to replace an a/c motor on a 2003 civic, wireing for blower control 2004 silverado

2005 Chevy Truck Silverado 1500 2WD Blower Motor Resistor Replacement

0

Filed Under (Chevy Manuals) by admin on 29-04-2012

download
Blower Motor Resistor Replacement Notes BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.

Related Content:

2005 chevy blower motor resistor ground connections, testing mazda 5 for faulty blower moror, resistor sl1, part number 05 silverado blower resistor fix, 07-2012 Tahoe blower motor resistor replacement, fan blower resistor for 1998 buick regal, how to change blower motor 2005 hummer h2, how to rotate resistor in schematics, NISSAN CHANGED BLOWER RESISTOR MAKING NOISE WHEN CRANK, removal/replacement of stepper motor in a 05 tahoe

Windshield Wiper Linkage Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
Installation Instructions 1. Place the Wiper Motor Mount Plate (FFR# 25391) along the edge of the ¾” shock tower support tube on the passenger side and the top of the footbox front wall aluminum. Mark the location for the riv nuts (4 total). 2. Drill the riv nut holes using a 25/64″ drill bit. You may want to begin by using a smaller drill bit to drill a pilot hole first (shown). 3 3. Intsall the 1/4″ riv nuts (4) using the supplied riv nut tool. 4. Install one of the rod ends (FFR# 25724) with the supplied jam nut (FFR# 25725) onto the wiper motor arm (1/2″, 9/16″ wrenches). You will have to trim some of the excess thread off of the rod end in order for it to have sufficient clearance between it and the wiper motor mount plate. 4 5. Place the wiper motor in the mount plate (FFR# 25391) so the pins on the motor fit inside the holes in the mount plate and the three threaded holes in the motor line up with the corresponding holes in the mount plate. 6. Using the three Corvette screws that held the motor in place, fasten the motor to the mount plate (T- 30 Torx). 7. Place a nylon spacer (FFR# 10960) between the frame and the mount plate at each of the riv nuts and bolt the plate into positon using the supplied ¼”-20 x 1.5″ long bolts (4mm allen).
6 ATTENTION: For the bolt at the front corner of the plate, you may have to use the supplied washers as well as the nylon spacer to prevent the bolt from bottoming out before the plate is firmly in place (See photo). 8. Screw the supplied section of threaded rod (FFR# 25723) into the rod end on the wiper motor. 7 9. Slide the aluminum tube (FFR# 25934) over the threaded rod and measure how much of the aluminum tube will need to be trimmed once the rod end is screwed on. Trim the tubing with a tubing cutter/hacksaw/cutoff wheel. 10. As you did with the rod end on the wiper motor, you will have to trim the threads on the rod end to clear the aluminum. 11. Place the aluminum tube over the threaded rod, then screw the rod end (FFR# 25724) onto the rod until tight. 12. Before installing the wheel box to the body you will have to trial fit the wiper arm to the wheel box. It is a tight fit, so you may have to spray the splines with some WD-40 or some oil and tap the wiper arm onto the splines. Remove the wiper arm from the wheelbox so you can bolt it to the body. 8 13. Follow the instructions in the assembly manual for bolting the wheelbox to the body. 14. Install the rod end on the wiper wheel box arm with the supplied jam nut (FFR# 25725) (1/2″, 9/16″ wrenches). 15. Install the wiper blade (FFR# 25629) onto the wiper arm (FFR# 25552). 16. Clip the wiper arm onto the shaft of the wiper wheel box, making sure that the tab on the arm clips into the channel on the wheel box shaft (clip shown). 9 17. Spray the windshield with water, or glass cleaner. Check the sweep by turning the wipers on – start with the slowest setting to avoid damaging the linkage or running the wiper beyond the windshield. Make any necessary adjustments, and the linkage installation is complete

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage

2001-2004 FORD Taurus WATER IN THE BLOWER CASE—BLOWER MOTOR SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 14-06-2011

download
SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z-19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the Figure 1 – Article 04-15-3 screen is fully seated. Inspect the rubber seal on the vent screen which should be fully seated 5. Locate the tape as shown (Figure 2). Remove against the windshield. If the cowl vent screen the tape and apply Clear Silicone Rubber is not fully seated and appears warped, it must TA-32 to the small hole as shown (Figure 2). be replaced (4F1Z-54018A16-BAA) 3. Remove the cowl vent screen per the vehicle model years and build date information. Workshop Manual Section 412-01 Pollen Filter Removal and inspect the cabin filter to confirm ISSUE it is fully seated. Re-seat the filter as Some vehicles built between 5/1/2001 and necessary. Inspect rain-hat base to make sure 12/15/2003 may exhibit water in the blower case or it is secure and sealed to the body. Reposition on the passenger side floor, an inoperative climate and reseal as necessary using Clear Silicone control blower motor, a motor that operates on high Rubber TA-32. speed only, and/or a blower motor resistor failure. 4. Remove the foam sealant expulsion at lower front outboard corner base of the rain-hat ACTION (Figure 1). Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details.

Related Content:

2001 saab 9-3 shop manual, Replacing blower fan on 2008 F2 50

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, ford 9 inch repair manual, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, heaf bolt torque specs 655a backhoe, windstar dtc u1131

Toyota Sequoia SR5 2001-2006, Toyota Tundra 2000-2006, Toyota Tundra D-Cab 2005-2006 Signal Mirror Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
1. Open the driver side door and lower the window. 2. Remove the door panel, kick panel, and plastic trim piece along the bottom of the door frame. 3. Disconnect the mirror wire harness. Remove the three mirror mounting nuts and remove the mirror housing from the vehicle. 1 2 3 Mirror Replacement – 2 – 4 There is a plug seated in a socket in the center of the mirror that holds the mirror in the mirror housing. Lift up the inboard edge of the mirror. Use a small pry bar and pry up around the center of the mirror until the plug unseats from the socket. 5 There are two drive pins on the bottom and outboard sides of the mirror. Hold the top of the mirror away from the mirror housing and pry away the bottom drive pin from the back of the mirror. 6 Hold the inboard side of the mirror away from the mirror housing and pry away the outboard drive pin from the back of the mirror. IF heated, disconnect OE heater wire from heater terminals. Note: During the removal of the original mirror, if motor pins stay attached to the back plate, use “V” end in small pry bar or needle nose pliers to disengage pins from back plate. Set the mirror aside. 7 8 Using the shorter of the two harnesses from the kit, tape the end without the mating connector to the end of the gopher wire. Remove the foam insulation from the mirror housing sail. Starting from the inside of the mirror housing, guide a piece of gopher wire down alongside the existing factory wire harness and out of the bottom of the mirror housing sail. 9 Pull the gopher wire and wire harness through the mirror housing until about 4 inches of wire remain inside the mirror housing.
13 Tuck the wire harness behind the Signal® mirror. Insert the other drive pin into the outboard pin socket (socket closest to the optic module). Align the socket in the center of the Signal® mirror over the plug on the center of the mirror mount. Align drive pins to its mating slots on the motor mount and vice-versa. Anti-vibration tab should be tucked inside housing. 14 Use the palm of your hand and firmly press down on lower portion (marked boundaries) of the Signal® mirror until it snaps into position. Press down carefully on the mirror outboard edge to engage outboard drive pin into mirror mount socket. 15 Press mirror down carefully on the lower edge to engage the lower drive pin into motor mount. Remount mirror to door, then use Electronic Hand Control to relocate mirror position. Gently clean any finger mark/dirt away from mirror using paper towel and glass cleaner. 10 Guide the Signal® mirror harness along the existing path of the factory wire harness and through the foam insulation. Remove any slack in the wire. Reposition the foam insulation on the mirror housing sail. 11 Connect the Signal® mirror mating connector to the Signal ® mirror harness. If heated , reconnect the heater wires to the heater terminals on the back of the new Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. Disregard heater connections on vehicles not equipped with outside heated mirrors. 12 The drive pins must be aligned before installing the Signal® mirror. If needed, insert a drive pin into the lower socket on the mirror mount. Align the nubs on the lower drive pin so it points to the round plug in the center of the mirror mount.

Related Content:

how to access to wiring harness for radio on 2006 Buick Lucerne, 2006 malibu door wiring diagram, Saturn ION-2 2 2 L4 GAS Wiring Diagram, Repairing a ford F-150 side mirror 2011, repair link pins on Tundra 2000, OnStar FMV Wiring Instructions, mirror glass removal f150, how to replace heated power mirror glass 2004 ford f150, how to remove a side mirror from a 1994 ford f150 truck, 2000 mercury cougar drivers side mirror free replacement instructions

4WD Switch Indicator Lights Flashing, 4WD Inoperative, DTCs C0327, P0500, P0836, P1875 Set (Replace Encoder Motor Sensor, Reprogram TCCM, Inspect Front Drive Axle Engagement Sleeve for Damage/Repair if Necessary)

0

Filed Under (More Manuals) by admin on 22-06-2012

download
Correction Important: For ease of reassembly, shift the transfer case assembly to 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8) prior to removing any components. For information on placing the NV246 (NP8) transfer case in NEUTRAL, see the procedure at the end of this bulletin. 1. Remove the transfer case and front axle/engine skid plates (if equipped). 2. Disconnect and position the front propeller shaft aside. 3. Disconnect the transfer case encoder motor wiring harness. 4. Remove the three (3) bolts that retain the encoder motor to the transfer case. 5. Separate the encoder motor assembly from the transfer case and place it on a work bench. Important: DO NOT REMOVE THE SCREWS INDICATED WITH THE (1) IN THE ABOVE ILLUSTRATION. 6. Remove the four screws on the outer perimeter of the encoder motor housing. Important: For proper timing and ease of reassembly, hold the gear in place as your remove the cover from the encoder motor assembly with your thumb or finger. 7. Carefully remove the cover from the encoder motor assembly. The cover has a seal on the bottom side. Place the cover in a position to protect this seal from damage and/or contamination. Important: Observe the location of the punch mark on the large gear in relation to the timing mark on the housing if the transfer case was placed in the 2HI for the NV263 (NP1), or Neutral for the NV246 (NP8). The timing marks should be within one tooth of proper alignment. If not, you must note the timing mark positions for reassembly. 8. Locate the two shims; one on the small gear and another on the larger gear. Set them aside on a clean surface for reuse. Important: After removing the large gear from the housing, a dark gray phenolic spacer should remain in the casting where the bottom of the large gear resides. Locate this spacer and save for reuse. 9. Carefully lift the large gear from the housing. The sensor and wiring harness will come with the gear. 10. Disconnect the wiring from the sensor. 11. Separate the sensor from the large gear.

Related Content:

encoder motor & encoder sensor for 2004 chev silverado z71

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram