Skip to content

hego fuse ford thunderbird 1997

You search PDF repair manual about hego fuse ford thunderbird 1997, if there are search results will appear below. If search results do not exist, please search by others keyword.

1994 Ford Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION/ INSTALLATION MANUAL

download
1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron. Fig. 5: Underhood Fuse Panel Identification (1994 -95 Models) Courtesy of FORD MOTOR CO. Fuse & Relay Identification 1 – 15 Amp DRL Module, Foglights 2 – 5 Amp Memory 3 – 20 Amp Ignition Coil 4 – 20 Amp Auto Shock WARNING: Always disconnect battery ground cable before servicing “high-current fuses. It is recommended that “high-current” fuses be replaced by a qualified technician. 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. Virtual Wrench

1997 Ford Thunderbird/Cougar Steering Column with Air Bag

download
Steering Column with Air Bag The steering column has a steering wheel (3600) which is bolted to the top of the steering column and is fitted with a supplemental air bag system. * Before performing work on or around any supplemental air bag system component, observe all supplemental air bag system conditions and warnings to avoid accidental air bag deployment and possible injury. * Refer to Section 01-20B for supplemental air bag system conditions and warnings. Steering Column, Tilt — Disassembled View Section 11-04: Steering Column 1997 Thunderbird/Cougar Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/16/2000 Item Part Number Description 1 043B13 Driver Side Air Bag Module 2 N804385-S100 Steering Wheel Bolt 3 3600 Steering Wheel 4 N805572-S36 Air Bag Module Retaining Screws (2 Req’d) 5 3L518 Steering Wheel Spoke Cover (2 Req’d) 6 N804385-S100 Screw 7 14A664 Air Bag Sliding Contact 8 13318 Turn Indicator Cancel Cam 9 3C610 Bearing Retainer 10 3520 Steering Column Upper Bearing Spring 11 3518 Steering Column Bearing Sleeve (Upper) 12 3517 Steering Column Bearing (Upper)(Small) 13 3517 Steering Column Bearing (Large) 14 3524 Steering Gear Input Worm Gear and Rack 15 390345-S36 Screw 16 13K359 Multi-Function Switch

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

1997 Ford Thunderbird/ Cougar Steering Column Removal And Installation Manual

download
Steering Column Disassembly CAUTION: Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle unless the column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated, as this will damage the air bag sliding contact. 1. Disconnect battery ground cable (14301). Refer to Section 14-01 . 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725), steering column upper bearing spring (3520), suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539). Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) assembly. 7. Remove bearing retainer (3C610) and steering column upper bearing spring. . Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518). 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear. 12. Remove two pivot bolts. Use caution becausesteering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511). 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723). 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681).