honda accord floor shifter shift knob

You search PDF repair manual about honda accord floor shifter shift knob, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda accord floor shifter shift knob Direct Download speed 5432 Kb/s

  honda accord floor shifter shift knob Full Version speed 8172 Kb/s



Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

2009 HONDA ELEMENT SC ALL-SEASON FLOOR MATS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 09-10-2011

download
INSTALLATION NOTE: •A floor mat hook prevents the driver’s side floor mat from sliding forward and possibly interfering with the pedals. •If you remove the driver’s side floor mat, make sure you reanchor it when you put it back in your vehicle. •If you replace the floor mat, use factory floor mats designed to be used with the floor mat hook. •Do not put additional floor mats on top of the anchored mat, otherwise the additional mats may slide forward and possibly interfere with the pedals. Installing the Floor Mats 1. Install the driver’s side floor mat by inserting the two front mat rings over the two floor mat hooks. 6303010K PASSENGER’S SIDE FLOOR MAT DRIVER’S SIDE FLOOR MAT HOOK FLOOR MAT 6206071K REAR FLOOR MAT FLOOR MAT HOOK FLOOR MAT 2. Install the passenger’s side floor mat. 3. Install the rear floor mat by inserting the floor mat ring over the floor mat hook

Related Content:

philips dens-o-mat 70 service manual, PHLIIPS DENS O MAT X-RAY TROUBLE SHOOT

2007 HONDA ACCORD 2 AND 4-DOOR LEATHER SHIFT KNOB (M/T) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 15-10-2011

download
INSTALLATION 1. Squeeze the ring while you pull down on the shift boot. Remove the shift knob by turning it counterclockwise. 2. Remove the shift knob from the ring by squeezing the retaining tabs and pushing it up with long nose pliers. 3. Transfer the ring to the leather shift knob 4. Install the leather shift knob on the shift lever by turning it in the clockwise direction. 5. Pull the boot upward. USE AND CARE Use a sponge or cloth and a solution of mild liquid dishwashing soap and water to clean the shift knob. Rinse the knob completely with water, then dry it with a shop towel. Never use organic solvents such as benzene, thinner, or gasoline to clean the shift knob.

2002 Chrysler 300M Special Floor Shift Service and Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 14-02-2012

download
Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp. 11. Remove cable from routing bracket (Fig. 256) 12. Remove cable-to-transaxle nut and slide cable off of stud (Fig. 255). 13. Disconnect shifter cable from shift lever assembly at transaxle (Fig. 255). 14. Remove cable from underneath vehicle. INSTALLATION 1. Make sure transaxle shift lever is in “Park.” This is the most rearward position. Verify park sprag is fully engaged by rotating either a tire or an axle shaft . 2. Position cable in vehicle and connect cable end to the transaxle shift lever (Fig. 255). 3. Verify that the washer (Fig. 255) is still in place on the cable mounting stud. Install cable to transaxle and tighten nut to 28 Nm (250 inch lbs.). 4. Rotate fill tube to original location. Install and tighten fill tube bracket bolt. 5. Install cable “push pin” into bracket as shown in (Fig. 254)

Related Content:

how install console shift handle 1999 taurus, 2002 expedition shifter cable disconnect, ford escape shift cable repair, 2006 gmc envoy rear hatch rubber boot wire harness, Dodge 3500 Brown how to install shifting cable, 2004 ford f150 transmission shift cable ends, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, need diagram of shifter cable for 2008 chevy malibu lt, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it

2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 21-01-2012

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, 2003 hummer H2 transmission shift connection, transmisson speed sencer on 2000 f150 how do you change it, lincoln continental p0743, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, how to install transmission shift solenoid buick regal ls 2000, replace shift solionide on honda crv 1999

2005 HONDA CIVIC HYBRID FLOOR MATS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 15-10-2011

download
INSTALLATION NOTE: A floor mat anchor is required for the driver’s side of the vehicle; the anchor prevents the front floor mat from sliding forward and possibly interfering with the pedals. If you remove the front floor mat, make sure you re-anchor it when you put it back in your vehicle. If you replace the floor mat, use factory floor mats designed to be used with the floor mat anchor. If you use a non-factory floor mat in the driver’s footwell, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat, otherwise the additional mats may slide forward and possibly interfere with the pedals. Identify each front floor mat by the identification mark on the back. The floor mat marked “R” goes on the right (passenger’s) side of the vehicle; the floor mat marked “L” goes on the left (driver’s) side of the vehicle 1. Slide the driver’s seat all the way back. 2. Below the driver’s seat, locate the slits in the carpet at two places along the front edge. 3. Turn over the slit carpet, locate the square hole in the body. Press the plastic grommet into the hole. 4. Attach both floor mat anchors to the body using one self-tapping screw for each anchor. Tighten the screws securely. 5. Install the driver’s side floor mat by placing the rings in the floor mat over the pins of the floor mat anchors.

Related Content:

honda fit floor mat anchors

2006 HONDA RIDGELINE FLOOR MATS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 15-10-2011

download
INSTALLATION NOTE: •Before installing, identify each floor mat. Remove the standard floor mats before installing these new floor mats. The floor mat holders are required for the driver’s side of the vehicle; the holder prevents the driver’s side floor mat from sliding forward and interfering with the pedals. 1. Install the driver’s side floor mat by placing the rings in the floor mat around two holders on the floor carpet. 2. Install the passenger’s side floor mat by placing the ring in the floor mat around one holder on the floor carpet. 3. Install the rear floor mat by placing the rings in the floor mat around two holders on the floor carpet

Honda Civic / Acura Integra Short Shifter INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 18-02-2011

download
INSTALLATION INSTRUCTIONS 1) Raise the vehicle. Use ramps or a jack and jack stands. NEVER work under a vehicle that is supported by the jack. 2) Remove the stock shift knob from inside the vehicle by twisting it counterclockwise. 3) Underneath the car, remove the bolt that attaches the shifter to the shift rod. Move the shift rod out of the way. 4) Remove the two locknuts and the shift ball holder plate. Pull the stock shifter out taking care to not damage the shift boot inside the car. 5) Inspect the shifter ball seat (plastic piece) and replace if worn or damaged. 6) Rub a small amount of white lithium or synthetic grease around the ball of the JG Edelbrock shifter. Guide the shifter up into the assembly. Before pushing it all the way in, guide the threaded end through the shifter boot from inside the vehicle. Make sure that the shifter bend is pointed towards the driver. 7) For Integra’s, use the long (45.5 mm) pin and the thick and thin aluminum spacers for side clearance. Lubricate the distance pin with white lithium or synthetic grease. 9) Re-install bolt and locking nut – torque to 16 ft-lbs. 8) For Civics, use the short (30.5mm) distance pin with the washers for side spacers. Lubricate the pin with white lithium or synthetic grease

2008 HONDA FIT ALL SEASON/ CARPET FLOOR MAT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 13-10-2011

download
4. Under the front of the driver’s seat, turn over the two strips of floor carpet to expose the two square holes in the floor panel concealed under them. Push a grommet into each square hole as shown. 5. Position the front holders on the grommets and install the two self-tapping screws. 6. Install the passenger’s holders the same way Installing the Front Floor Mats 7. Match the two holes in the driver’s side mat and passenger’s side mat with the pins on the holders and install the floor mat on the driver’s side and passenger’s side. 2. Make cuts with a utility knife at the slits in the floor carpet at the two locations shown. 3. Cut the insulator matching the previously cut hole. Installing the Rear Holders 8. Slide the front passenger’s seat completely forward. REAR SLIT UTILITY KNIFE CUT-OUT FRONT SLIT REAR FLOOR MAT Position the mat and check the location of the slits. 2 SLITS Slide the floor mat against the front seat rails. FRONT SEAT RAILS FLOOR MAT 9. Using the right rear mat as a guide locate the slits in the floor carpet, and then remove the floor mat. 10. Using a utility knife, cut the two slits in the floor carpet on the passenger side and remove the round piece of carpet. 11. Using scissors, cut the dashed lines to separate the two templates and trim one corner of the rear template

Toyota Minivans Wheelchair-Accessible Lowered Floor Conversion REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 09-03-2012

download
One-Touch Electronic Control System: The Rampvan One- Touch electronic control system provides simple one-touch activation of all Rampvan power features. For your convenience, the control system can be activated using the Toyota remote keyless entry transmitter, any of the interior-mounted control switches or the optional magnetic entry. Power Passenger Side Sliding Door: The One-Touch electronic control system activates the passenger side power slide door for ramp access. The slide door and lowered floor configuration provides a 53-1/2″ clear vertical passageway. Note: The driver side sliding door is lowered to provide a clear passage also. Ramp: A fully automatic 30″ wide power infloor ramp provides an unobstructed doorway, maximum visibility and increased interior space (with manual override capa- bility). Electromechanical Power Kneeling Rear Suspension: “Kneeling” is the lowering motion of the electromechanical rear suspension. The kneel feature reduces the slope of the ramp when deployed. Lowered Floor from Rear Axle to Firewall: This feature provides additional headroom (58″ floor-to- ceiling at center of van), and further reduces the slope of the ramp when deployed. OEM factory carpeting is featured throughout the lowered floor area. Ground Clearance: The lowered floor results in reduced ground clearance. Be aware of limited ground clearance. Ground Effects: Exterior color- matched ground effect panels conceal the lowered floor and lowered sliding doors. Forward-Facing Wheelchair and Occupant Belt/Track System: One Forward-Facing Wheelchair and Occupant Belt Kit is supplied for the restraint of one wheelchair and occupant. The belt kit is used in conjunction with the floor track. Note: Additional belt kits can be purchased (option) Floor Track for Wheelchair and Occupant Securement in Midpoint Lowered Floor Area: Floor track provided in the midpoint lowered floor area (Position C ) can be utilized for restraint of wheelchair passenger(s). Wheelchair capacity at midpoint may have limitations based on the dimensions of specific wheelchairs. Quick-Release Front Passenger Seat with Floor Track for Wheelchair and Occupant Securement: The passenger seat (Position B ) is equipped with quick-release seat attachments (making seat removal and installation procedures simple). The seat can be removed and the seat location can be utilized by a wheelchair occupant (floor track provided).

Related Content:

Van Power Sliding Door Kit

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock