honda civic hybrid ima dtc codes

You search PDF repair manual about honda civic hybrid ima dtc codes, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda civic hybrid ima dtc codes Direct Download speed 5432 Kb/s

  honda civic hybrid ima dtc codes Full Version speed 8172 Kb/s



2001-2005 HONDA Civic Warranty Extension CVT Drive Belt Slippage

0

Filed Under (Honda Manuals) by admin on 05-06-2011

download
DIAGNOSIS NOTE: You must complete the diagnosis before attempting any CVT repairs. 1. Civic Hybrid and Insight only: Make sure the IMA battery level gauge shows at least three quarters charged. If you need to increase the IMA charge, do this: • Insight only: Remove the EPS (electronic power steering) fuse from the under-hood fuse/relay box. •Start the engine, and run it at 3,500 rpm until the battery level gauge shows at least three quarters charged. • Insight only: Reinstall the EPS fuse. 2. Connect the HDS to the vehicle’s DLC, then turn the ignition switch to ON (II), and turn on the HDS. 3. At the HDS screen prompts, enter the VIN (if prompted) and the odometer reading. 4. At the SELECT MODE screen, select HONDA SYSTEMS . 5. At the SYSTEM SELECTION menu, select A/T . 6. From the MODE MENU, select SNAPSHOT . 7. Set these snapshot points: •Trigger type: Manual •Recording time: 2 minutes •Trigger point: -60 seconds 8. Find a flat stretch of road where you and an assistant can drive for 2 minutes at a steady vehicle speed. 9. Make sure the engine is at normal operating temperature, then using the appropriate vehicle chart below, select a vehicle speed (40, 50, 60, 70, or 75 mph) for your 2-minute snapshot. NOTE: Do not exceed the posted speed limits. Civic GX Civic HX Civic Hybrid Insight 10. Accelerate to the vehicle speed you selected, then have your assistant tap the camera icon on the HDS to trigger the snapshot. Do your best to maintain the vehicle speed and the throttle position during the snapshot. NOTE: Turn the A/C off before you capture the snapshot. 11. When the 2-minute snapshot is finished, have your assistant follow the screen prompts to save the data.

Related Content:

honda insight manual 2009, ima battery sale honda insight 2001, honda insight user manual 2009

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 16-01-2012

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

Related Content:

Service bulletin 020139007, 020139007, 020139007 service bulletin, battery restoration procedure, chevrolet service bulletin 020139007, servicing a battery module honda insight

2004 Ford Explorer/Mountaineer Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw Control Disabled ABS Module This DTC will be set if the stability assist system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment, or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test Q . C2769 (ABS only) Longitudinal Acceleration Sensor Circuit Failure ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2769 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Circuit Failure ABS Module Go To Pinpoint Test H . C2770 (ABS with Stability Assist) Longitudinal Acceleration Sensor Signal Fault ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Signal Fault ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2770 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2777 Sensor Cluster Bus Failure ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault Section 418-00 . U1901 CAN Network #2 Communication Bus Fault- Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault received from external node Network Fault Section 418-00

Related Content:

WHERE IS 2002 DAKOTA CENTRAL TIMING MODULE, ABS fault on Tahoe, hino 05 air brake fail abs, where is yaw sensor located on a 2002 ford explorer, how to replace vats module on 1997 buick lesabre, gmc hvac relearn, ford u1901 steering angle sensor, ford u1901 escape, ford relearn after abs sensor trans harsh, FORD FUSION U1900-ABS CAN Communication BUS Fault

1996 Pontiac Grand Am DTC P0502 Vehicle Speed Sensor (VSS) Circuit Low Input (3.1L VIN M) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 06-07-2012

download
Action Taken When the DTC Sets Conditions for Clearing the MIL/DTC Diagnostic Aids Test Description The numbers below refer to the step numbers on the diagnostic table. 2. This step verifies that the PCM is receiving a signal from the vehicle speed sensor. 3. This step verifies that there are no opens in the circuitry from the vehicle speed sensor to the PCM connector. 7. This step performs a resistance test on the VSS circuits from the PCM connector. • The transmission defaults to 3rd gear. • The PCM inhibits TCC operation. • The PCM illuminates the Malfunction Indicator Lamp (MIL). • The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. • A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. • The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. • Check for PRNDL DTC P0705. DTC P0705 affects transmission operation. This may set DTC P0502 falsely. • Check for Electromagnetic Interference (EMI) in circuits 400 and 401. EMI may be induced if the harness is routed along the spark plug wires. • Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring at the TCC brake switch. Look for the following conditions: – A bent terminal – A backed out terminal – A damaged terminal – Poor terminal tension – A chafed wire – A broken wire inside the insulation • When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. • Ensure that the VSS is securely tightened to the case extension. DTC P0502 Vehicle Speed Sensor Circuit (VSS) Low Input

Related Content:

1993 taurus EATC wiring harness, pcm 40i transmission troubleshooting, 1991 subaru loyale haynes repair manual free download, mazda obd2 reads no dtc presently stored in vehicles computer, chevy 3100 pcm malibu location, 96 town and country p1495, 7 3 Powerstroke PCM Failure Symptoms, 2002 sable pcm replace, 1996 Honda Accord PCM, vss hino

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)

Related Content:

Fuse box honda pilot cigatette lighter, honda civic 09 cigarette lighter fuse, locationof2013sonicfuselocation, 2012 HONDA CRV AUX FUSE LOCATION, mirrors on 2013 rav4 not auto moving fuse location, 2011 honda pilot fuse identification, 1990 corvette intake manual removal, bmxa apply chart, 2007 civic main relay locations, inside fuse box 2005 honda civic

2000 Ford Pickup F250 Super Duty TEST DE: EXHAUST BACKPRESSURE (EBP) SENSOR

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
DTC P0470 This DTC indicates PCM detected EBP sensor malfunction during KOEO ON-DEMAND SELF-TEST. Possible causes for this DTC are: Faulty EBP Sensor • Open Or Shorted Circuit • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. If EBP reading is less than 18.5 psi, clear DTCs. Repeat KOEO ON-DEMAND SELF-TEST . If DTC is still present, replace PCM. If EBP reading is 18.5 psi or more, go to next step. 2) Check Signal Ground Circuit Turn ignition off. Disconnect EBP sensor connector. Sensor is located on top front of engine. Inspect for damaged pins, corrosion and loose wires. Repair as necessary. Measure resistance between ground and Gray/Red wire at EBP sensor wiring harness connector. See Fig. 11 . If resistance is less than 5 ohms, replace EBP sensor. If resistance is 5 ohms or more, locate and repair open circuit in Gray/Red wire. 3) Continuous DTC P0470 This DTC indicates PCM detected a EBP sensor malfunction during normal driving conditions. Possible causes for this DTC are: Faulty EBP Sensor • Faulty Connection • Faulty PCM • Ensure scan tool is connected to Data Link Connector (DLC). Using scan tool, select EBP PID from PID/DATA monitor menu. While observing EBP PID, wiggle and bend small sections of wiring harness starting at EBP sensor connector and working toward PCM. If EBP reading fluctuates, isolate fault and repair as necessary. If reading does not fluctuate, go to next step. 4) Check Connector Disconnect EBP sensor connector. Sensor is located on top front of engine. Disconnect PCM 104-pin connector. Inspect connectors for damaged pins, corrosion and loose wires. Repair as necessary. Clear DTCs and repeat QUICK TEST . If both connectors are okay, no problem is indicted at this time. 5) DTC P0471 This DTC indicates PCM detected an EBP sensor malfunction during normal driving conditions and with EBP sensor enabled. Possible causes for this DTC are: Faulty EBP Sensor. • Plugged Or Restricted Sensor Supply Tube • Damaged Exhaust Pressure Regulator (EPR) Linkage Or Butterfly Damage • Faulty PCM • Perform KOER ON-DEMAND SELF-TEST . If any DTCs are present, repair fault(s) before continuing with this test. Using scan tool, select EBP PID from PID/DATA monitor menu. Road test vehicle performing hard accelerations while monitoring EBP PID. If EBP reading increases to more than 25 psi with EBP sensor on, no problem is indicated at this time. If EBP reading does not increase to more than 25 psi, go to next step

Related Content:

2007 nissan frontier camshaft position sensor location, Chevy Traverse Bank 2, 2000 Infiniti Q45 Problems, how to check oil in front crank case 2005 tahoe, 02 sensor problems 2010 prius, o2 sensor bank 1 tundra, location of front heated exhaust oxygen sensor Saturn SL two 2002, locate 2011 traverse coolant temperature sensor, install cam sensor kia 05 sedona, HOW TO REPLACE WINSHIELDS ON MACK CV-713

1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 24-06-2012

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?

Related Content:

p1626 chevy venture, 87 bonco 2 parking brake control assembly diagram, what is a class 2 malfunction, VTD? chevrolet, universal theft deterrent system for 1996 bonneville, theft deterrent module location 99 olds intrigue, hummer h3 passlock starting issue, how to reset factory lock on h3, GM Theft Deterrent System Problem, gm passlock 1 bypass instructions

Kia 2002 Saturn SL will set if TP sensor voltage is less than 0.2 volts

0

Filed Under (Kia Motors Manuals) by admin on 26-05-2011

download
The throttle position (TP) sensor is a potentiometer that varies resistance according to changes in throttle plate position. The powertrain control module (PCM) measures the signal voltage from the TP sensor which is a reduced value of the PCM 5-volt reference. The voltage ranges from 0.4 (+/-0.2) volts at 0% throttle position to 4.7 volts at wide open throttle. DTC P0122 sets when the TP sensor signal voltage at the PCM is below the calibrated voltage value. DTC Parameters DTC P0122 will set if TP sensor voltage is less than 0.2 volts when: z The condition exists for longer than 10 seconds. z The ignition is ON. DTC P0122 diagnostic runs continuously with ignition ON. DTC P0122 is a type A DTC. Diagnostic Aids Important If DTC P1635 is set, diagnose that DTC first. 2002 Saturn SL
To locate an intermittent problem, use a scan tool to monitor TP SENSOR voltage with ignition ON, engine OFF. Wiggling the wires while watching for a change in TP SENSOR voltage may locate the area where an open or short to ground in the wiring could lie. An intermittent open in the TP SENSOR can cause this DTC to set. Use the scan tool to monitor TP SENSOR as the accelerator pedal is slowly depressed. The voltage should change smoothly from 0.4 volts at 0% throttle, to 4.7 volts at wide open throttle (+/-0.2 volts).

1999-2001 Infiniti Q45 MIL “ON” REAR O2 SENSOR DTC SERVICE PROCEDURE

0

Filed Under (Infiniti Manuals) by admin on 07-01-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2/4 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 1999-2001 Q45 23710-3H000, -3H001, -3H005, -3H006, -3H007 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Perform ECM Reprogramming on page 3. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. SELF-DIAG RESULTS SYSTEM ENGINE DATE 01/24/2002 5:35:07 P/N 23710-3H000 DTC Code TP020024 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 3/4 ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

2007 ecm location saturn vue, 2008 chevy 3 5 repair manual, how to replace ECU on 2005 Cadillac CTS, infiniti q45 manual torrent, mercedes cis repair manual pdf, manual pdf de hino dutro, lincoln ecm reprogramming, instructional how to reset the ECM on a 2004 Cadillac CTS, Ford 1998 E350 loction of the ecm, ecm update audi 2006 list

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

0

Filed Under (Honda Manuals) by admin on 05-06-2012

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.

Related Content:

1996 Odyssey Repair Manual PDF, 1996 Honda Accord Manual PDF, 1996 Honda Civic DX manual

Related Content:

honda insight manual 2009, ima battery sale honda insight 2001, honda insight user manual 2009