adjust shift cable gmc sierra 1999

You search PDF repair manual about adjust shift cable gmc sierra 1999, if there are search results will appear below. If search results do not exist, please search by others keyword.



  adjust shift cable gmc sierra 1999 Direct Download speed 5432 Kb/s

  adjust shift cable gmc sierra 1999 Full Version speed 8172 Kb/s



2002 Chrysler 300M Special Floor Shift Service and Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 14-02-2012

download
Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp. 11. Remove cable from routing bracket (Fig. 256) 12. Remove cable-to-transaxle nut and slide cable off of stud (Fig. 255). 13. Disconnect shifter cable from shift lever assembly at transaxle (Fig. 255). 14. Remove cable from underneath vehicle. INSTALLATION 1. Make sure transaxle shift lever is in “Park.” This is the most rearward position. Verify park sprag is fully engaged by rotating either a tire or an axle shaft . 2. Position cable in vehicle and connect cable end to the transaxle shift lever (Fig. 255). 3. Verify that the washer (Fig. 255) is still in place on the cable mounting stud. Install cable to transaxle and tighten nut to 28 Nm (250 inch lbs.). 4. Rotate fill tube to original location. Install and tighten fill tube bracket bolt. 5. Install cable “push pin” into bracket as shown in (Fig. 254)

Related Content:

how install console shift handle 1999 taurus, ford escape shift cable repair, 2002 expedition shifter cable disconnect, need diagram of shifter cable for 2008 chevy malibu lt, 2004 pontiac sunfire sunroof repair, 2004 ford f150 transmission shift cable ends, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, how to repalce gear shift cover on toyota sienna 2006

2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 21-01-2012

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, expedition shift solenoid b, transmisson speed sencer on 2000 f150 how do you change it, 2005 ford escape stuck shifter button, 2003 hummer H2 transmission shift connection, how to install transmission shift solenoid buick regal ls 2000

2001 Pontiac Grand Prix Shifter A/T Service and Repair Shift Control Replacement

0

Filed Under (Pontiac Manuals) by admin on 11-06-2011

download
Removal Procedure 1. Remove the horseshoe clip (1) from front of shift control knob, and remove knob. 2. Remove the Console Trim Plate. 3. Remove the console wiring harness. 4. Remove the console shift control wiring harness. 5. Remove the automatic transaxle range selector cable. 6. Remove the park/lock cable. 7. Remove the console shift control nuts. 8. Remove the console shift control. Installation Procedure 1. Install the console shift control. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the console shift control nuts. ^Tighten the console shift control nuts to 24 Nm (18 ft. lbs.) . 3. install the park/lock cable. 4. Install the automatic transaxle range selector cable. 5. Install the console shift control wiring harness. 6. Install the console wiring harness. 7. Install the Console Trim Plate. 8. Adjust the transaxle range selector cable.

Related Content:

how to remove the center console from a 2005 kia sorento, 1998 Mercedes Benz SLK 230 shifter locks and wont shift lower than Drive, 5r110w rebuild manual pdf, démontage console kia sorento, how to fix auto shifter on pontiac g6 2009, remove console kia sorento, remove overhead console 2008 jaguar

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 checrolet colorodo emmisions purge valve, 2008 pilot alternator replacement, 2008 ford xlt f150 free pdf service manual, FREE PDF DOWNLOAD OF 2008 SILVERADO Z71 REPAIR MAMUAL, ac drain on a 2008 silverado, 2008 ford fusion transmission sensor

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 27-06-2012

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

Related Content:

1999 honda civic ex manual, ashley recliner model 7528 parts, 2001 civic fuel canister pdf, ashley recliner model 7528 replacement parts, Honda Odyssey 2001 Parts Diagram, honda odyssey 2002 repair manual pdf, honda odyssey canister purge valve location, Savage Model 99 Manual, viper 4115v1remote start

1999 FORD EXPLORER/ RANGER TRANSMISSION-4R44E OR 5R55E-SLIPPING SHIFT/ DELAYED OR NO ENGAGEMENT REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 18-05-2012

download
SERVICE PROCEDURE F87Z-7A100-DB Main Control (4.0L EI Explorer) F87Z-7A100-EB Main Control (4.0L SOHC Explorer) 1. Perform normal diagnosis for this concern. XL2Z-7L491-AA Bracket XL2Z-7G383-AA Electronic Pressure Control (EPC) 2. Perform Line Pressure Tests as listed in the Solenoid 1999 Explorer/Mountaineer, Ranger Workshop Manual. OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The 3. If pressures are low, perform Pinpoint Test for Provisions Of Bumper To the EPC solenoid. Bumper Warranty Coverage And Emissions Warranty 4. Inspect the bracket that attaches the Torque Coverage Converter Clutch (TCC), Shift Solenoid B OPERATION DESCRIPTION TIME (SSB), Shift Solenoid D/Coast Clutch Solenoid 991610A Replace Electronic 1.2 Hrs. (SSD/CCS), and EPC solenoids to the main Pressure Control (EPC) control for damage. If the bracket is damaged, Solenoid And Clean Main replace both the bracket and solenoid. Control (Includes Time For 5. If the bracket is not damaged, inspect the Road Test) – 4R44E Or solenoid for the affected date code (refer to the 5R55E following Manufacturing Date Code Chart) and 991610B For Line Pressure And ID marking (Figure 1, Views 1, 2, and 3). If the Pinpoint Tests, Use “A” solenoid is one of the affected, replace it. Time As Outlined In The Warranty And Policy MANUFACTURING DATE CODE Manual Date Code Month/Year DEALER CODING 868xx August 1998 CONDITION 869xx September 1998 BASIC PART NO. CODE 870xx October 1998 7G383 01 871xx November 1998 OASIS CODES: 501000, 502000, 50300

Related Content:

replacing manual, how replace torque converter clutch solenoid on a 1998 suburban, escort transmission harsh engagement, replace ford explore sports 1999 clutch line, remove r lower control arm 1998 olds 88 what electric impack wrench to usee, 5r55e tcc, 02 expedition tcc solenoid replacement manual, how to remove a epc solenoid from a1998 ford expedition transmission, isuzu trooper fuel solenoid valve location, pictures removing the epc solenoid on a1998 f150

1993-2002 Camaro/ Firebird CAGS SKIP SHIFT NSTALLATION INSTRUCTIONS

0

Filed Under (Chevy Manuals) by admin on 27-11-2011

download
INSTALLATION PROCEDURES: 1. Disconnect the negative (black) battery cable from the battery. 2. Raise the vehicle using ONLY the proper procedures outlined in the factory GM Service Manual. To order a service manual for your vehicle, call Helm, Inc. at 1-800-782-4358. THINK SAFETY FIRST! ALWAYS MAKE SURE THE VEHICLE IS PROPERLY SUPPORTED PRIOR TO WORKING UNDERNEATH IT. 3. Remove the Blue/White cap from the JET CAGS Skip Shift. Disconnect the factory wiring harness from the skip shift solenoid on the left rear (Driver’s Side) of the transmission. Plug the blue/white cap into the skip shift solenoid on the transmission sealing the connection from the elements. 1 2 GM, Camaro, Firebird are registered trademarks of the General Motors Corporation. Rev. 696030 REVERSE LOCKOUT SOLENOID SKIP SHIFT SOLENOID VEHICLE SPEED SENSOR BORG-WARNER (T56) 6-SPEED MANUAL TRANSMISSION FRONT 3 Plug the factory harness into the JET CAGS Skip Shift. Secure the factory harness and skip shift with the supplied tie wrap to keep the harness and skip shift with the supplied tie wrap to keep the harness from dangling/ dragging. 4. Lower vehicle following safety procedures and re-connect the negative battery cable.

Related Content:

what transmission 2002 camareo manual

1998-1999 Chevrolet and GMC S/T Pickup and 2 Door Utility Incorrect Fuel Gauge Readings

0

Filed Under (Chevrolet Manuals) by admin on 28-05-2011

download
Condition Some owners may comment on incorrect fuel gauge readings. The fuel gauge may read empty (E) with approximately 1/3 of a tank of fuel remaining, or the fuel gauge rarely reaches the full (F) mark when the fuel tank is filled. Correction Reprogram the vehicle control module (VCM) with the revised Fuel System Calibration. Use the appropriate calibration listed below. Refer to the latest Techline information for programming procedures. Calibration Information Important: These calibrations are not available from GMSPO. These calibrations are available Subject: Incorrect Fuel Gauge Readings (Reprogram Vehicle Control Module with Revised Calibration) Models: 1998*-99 Chevrolet and GMC S/T Pickup and 2 Door Utility Models 1998*-99 Isuzu Hombre with 4.3L Engine (VINs W, X – RPOs L35, LF6) *RPO ZN4 Only Plant Division VIN Breakpoint Linden Chevrolet (Blazer) XK162355 Linden GMC (Pickup) XK508493 Linden GMC (Jimmy) XK508505 Shreveport Chevrolet X8140835 Shreveport GMC X8512385 Shreveport Isuzu (RPO ZN4 W8668201-W8670669 Shreveport Isuzu X8650007-X8650733 Calibration P/N (New) Application 09374032 (Fuel System Calibration) S/T 100 (Pickup) &LF6/L35 09374033 (Fuel System Calibration)

Related Content:

2011 gmc sierra location of tps, 1998 chevy sierra gmc manual, 1hdfte nozzle repair, Isuzu 1997 wiring diagram between coil and distributor

2002 NISSAN ALTIMA MANUAL A/C TEMPERATURE NOT ADJUSTABLE REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 11-05-2012

download
SERVICE PROCEDURE 1. Remove the following components; • cluster lid “C” (HVAC control surround trim) • fuse box cover • driver’s side instrument panel lower cover (attached with 2 screws). 2. Remove the screw from the center of the cable operated gear (see Figure 2). Figure 2 3. Locate the small (about 1″ dia.) white air mix door gear. Hopefully it is still on the floor. NOTE: If you cannot find the old air mix door gear, order a new gear. Refer to the Parts Information section of this bulletin. 4. To see how it is supposed to fit, temporarily install the gear into the air mix door shaft (see Figure 3). Figure 3 Air mix door drive gear (shown installed) Heater box Cable operated gear Retaining screw (remove) Front TP020106 Cable (do not detach) On the left side of the heater case, remove the screw from the center of the cable operated gear for the air mix door. Note: It is not necessary to detach the cable from the gear or the heater box. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. Front TP010607a The gear can fit two different ways, only one of which is correct. Install the gear and rotate the gear/mix door shaft assembly fully clockwise so the gear’s index pin is at the 2 to 3 o’clock position. Cable (do not detach) Note: If the gear is in the correct spot, the alignment pin will be at the 2 to 3 o’clock position. POSITIONING THE GEAR CORRECTLY IS CRITICAL TO GETTING THE DOOR TIMING RIGHT. 3/5 5. Remove the gear, thoroughly clean the gear shaft of any grease, and apply the glue. See Figure 4. Figure 4 6. Re-install the gear into the mix door shaft (see Figure 5). Figure 5 TP010606a Air mix door gear (back side) Apply Glue to Shaded areas b. Apply plastic glue (3M dp-8005 or equivalent) to the shaft of the air mix door gear in the area where it inserts into the air mix door shaft. a. Thoroughly clean the air mix door gear shaft. Note: It is not necessary to clean the grease from the gear teeth. Front TP020100 Re-install the gear so the gear’s index pin is at the 2 to 3 o’clock position when the gear/mix door shaft assembly is turned fully clockwise. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. 4/5 7. Set the HVAC control temperature dial as shown in Figure 6. Figure 6 8. Re-install the cable operated gear (see Figure 7). Figure 7 9. Operate the temperature control while watching the air mix door gear movement. They should operate freely with no binding. 10.Check the adjustment of the temperature cable as follows: A. Rotate the temperature control knob to the full COLD position (i.e., fully counterclockwise) and confirm the air mix door is fully seated (sealed) in the down position, then B. Rotate the temperature control knob to the full HOT position (i.e., fully clockwise) and confirm the air mix door is fully seated (sealed) in the up position. If the air mix door does not fully seat (seal) in either the full HOT or full COLD position: • Adjust the temperature control cable, with the temperature control knob in the full hot position, using the clip at the heater unit (see Figure 7) 11.Re-install the trim pieces removed in step 1.

Related Content:

how to check the backlash between the camshaft gear and the adjustable idler gear for 3406 e monel, used set of pistons for 2000 nissan altima with2 2, how to fix a shifter in a 2000 chevy malibu, VVTI GEAR POSITION DETERMINED BY CAM SENSOR WAVEFORM, how to fix a broken column shifter on a 2003 toyota sequoia, how to change shift boot hummer h3, how do i replace the rear differential seal in my 2006 kia sorento ex 4wd, Gear shift nob broken on 2000 Chev Malibu, gear selector for 00 rodeo only goes in first and reverse, how to fix a loose metal knob control panel on a window whirlpool room ac

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals, Uncategorized) by admin on 23-04-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

Related Content:

2000 Isuzu 5 7 NPR Repair Manual lower intake manifold, charging system on 1999 isuzu npr not charging gas engine, ford five hundred instrument panel, remove ac panel from ford five hundred

Related Content:

how install console shift handle 1999 taurus, ford escape shift cable repair, 2002 expedition shifter cable disconnect, need diagram of shifter cable for 2008 chevy malibu lt, 2004 pontiac sunfire sunroof repair, 2004 ford f150 transmission shift cable ends, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, how to repalce gear shift cover on toyota sienna 2006