Skip to content

how do i install a capacitor at the blower motor control module connector on a 2004 grand prix

You search PDF repair manual about how do i install a capacitor at the blower motor control module connector on a 2004 grand prix, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

1999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation Manual

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the driver side air bag module. For additional information, refer to Section 501-20B . 2. Remove the passenger side air bag module. For additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connector. 7. Disconnect the windshield wiper motor electrical connector. * Release the wiring harness locators. 8. Disconnect the LH engine compartment in-line electrical connectors. 9. Unseat the LH wiring harness grommet 10. Disconnect the blower motor electrical connector. 11. Disconnect the A/C pressure cut-off switch electrical connector. 12. Disconnect the RH engine compartment in-line wiring harness connectors. 13. Disconnect the vacuum line at the intake manifold. 14. Disconnect the electronic air temperature control (EATC) variable blower motor controller electrical connector. * Release the wiring harness locators. 15. Remove the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 16. Remove the upper front fender splash shield bolts. 17. Remove the lower front fender splash shield bolt and locator. 18. Position the front fender splash shield away from the dash panel. 19. Unlock the wiring harness guide. 20. Unseat the RH wiring harness grommet. 21. Install the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 22. Remove the RH instrument panel lower insulator. 1. Remove the pin-type retainers. 2. Release the locking tab. 3. Remove the instrument panel lower insulator. * Disconnect the courtesy lamp.

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

2001-2004 FORD Taurus WATER IN THE BLOWER CASE—BLOWER MOTOR SERVICE PROCEDURE

download
SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z-19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the Figure 1 – Article 04-15-3 screen is fully seated. Inspect the rubber seal on the vent screen which should be fully seated 5. Locate the tape as shown (Figure 2). Remove against the windshield. If the cowl vent screen the tape and apply Clear Silicone Rubber is not fully seated and appears warped, it must TA-32 to the small hole as shown (Figure 2). be replaced (4F1Z-54018A16-BAA) 3. Remove the cowl vent screen per the vehicle model years and build date information. Workshop Manual Section 412-01 Pollen Filter Removal and inspect the cabin filter to confirm ISSUE it is fully seated. Re-seat the filter as Some vehicles built between 5/1/2001 and necessary. Inspect rain-hat base to make sure 12/15/2003 may exhibit water in the blower case or it is secure and sealed to the body. Reposition on the passenger side floor, an inoperative climate and reseal as necessary using Clear Silicone control blower motor, a motor that operates on high Rubber TA-32. speed only, and/or a blower motor resistor failure. 4. Remove the foam sealant expulsion at lower front outboard corner base of the rain-hat ACTION (Figure 1). Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details.

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.