Skip to content

how do i replace 2004 mercury sable transmission cooling line

You search PDF repair manual about how do i replace 2004 mercury sable transmission cooling line, if there are search results will appear below. If search results do not exist, please search by others keyword.

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

1999 Mercury Sable V6-3.0L DOHC A/ T-Cooler Flushing Service Manual

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers. ^They do not provide the volume necessary to remove heavy contaminants. ^They evaporate quickly and essentially leave contaminants in pockets, bends, or wherever they are as the solvent dries. ^TORQSHIFT, 4R100, E40D, C6 – The REAR transmission case filling receives the return line. ^4R70W, AODE, AOD – The TOP transmission case filling receives the return line. ^A4LD, 4R44/55E, 5R55E, 5R55N, 5R55W, 5R55S The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes

1999 Mercury Sable A/ T – Cooler Flushing Service Manual

download
SERVICE PROCEDURE Prior methods of cooler flushing have not obtained the level of cooler cleaning and contaminant removal that is required to prevent repeat repairs. The “Turbo-Tank Heated Cooler Line Flusher” uses heated Automatic Transmission Fluid ( ATF ) and a pulsating action to loosen system contamination. Previous equipment used solvents to clean & flush coolers, lines and torque- converters. There are 2 issues with this method: Aerosol Solvents should never be used for several reasons. NOTE YOU MUST IDENTIFY THE RETURN COOLER LINE TO START THE BACK FLUSHING PROCEDURE. A quick way to identify the return cooler line (fluid coming out of the cooler and returning to the transmission) is to locate the return cooler line fitting on the transmission case . Refer to the following lists: Rear Wheel Drive ^Residual solvent contamination can cause damage to friction bonding materials within the transmission (Clutches and Bands). ^Lack of fluid heating and agitation prevents this method from completely removing contamination from lines, in-radiator coolers and auxiliary coolers Front Wheel Drive NOTE IF AN IN-LINE FILTER HAS BEEN INSTALLED IN THE COOLER LINE, IT MUST BE REMOVED BEFORE FLUSHING THE COOLER OR COOLER LINES. Purge the cooler and cooler line before flushing: Located on the “Turbo-Tank Heated Cooler Line Flusher” is a fluid transfer and purge valve. This valve can be used to purge the cooler and cooler lines of contaminated fluid before starting the back flush procedure of the fluid cooling system (refer to step 5a of this Service Procedure or Equipment instructions, supplied with the “Turbo-Tank Heated Cooler Line Flusher”). Flush Procedure -The TOP transmission case filling receives the return line. ^CD4E – The REAR or Pump End transaxle case fitting receives the return line. ^4F27E – The REAR or Cover End transaxle case fitting receives the return line. ^AXOD, AXODE, AX4S, AX4N, 4F50N – The BOTTOM transaxle cooler line fitting receives the return line. 1. Check and top off fluid level of the “Turbo-Tank Heated Cooler Line Flusher” tank with transmission fluid. 2. Allow the fluid in the flusher 15-30 minutes to heat up to 140°F (60°C) before using. 3. Install line adapters into the transmission cooler lines. 4. Attach the flusher’s blue line to the transmission return cooler line quick disconnect. 5. Attach the flusher’s red line to the transmission outlet cooler line quick disconnect. a. Follow equipment instructions, to purge cooler lines and cooler prior to starting flushing procedure (using factory installed purge valve and clear hose on “Turbo-Tank Heated Cooler Line Flusher”). 6. Allow the cooling system to back-flush for 10-15 minutes, then flush the cooler in a forward/normal flow direction for an additional 10-15 minutes.

2002 Mercury Sable V6-3.0L VIN 2 Flex Fuel Repair Manual

download
Automatic Transmission/Transaxle Tune-Up B 0.0 1.5 Notes Includes: R&R Trans Pan, Service Filter And Make All Necessary Adjustments. Diagnose/Test AX4N/4F50N Oil Leak, Diagnosis B 0.0 0.5 Notes Includes: Clean And Dry Outside Of Case And Operating Unit To Determine Point Of Leakage. Transaxle, Diagnosis A 0.0 1.8 Notes Includes: Time To Hook-Up And Disconnect Test Equipment. Checking System For Fault Codes, Road Test And Hydraulic Pressure Test As Required. AXOD-E, AX4S Oil Leak, Diagnosis B 0.0 0.5 Notes Includes: Clean And Dry Outside Of Case And Operating Unit To Determine Point Of Leakage. Transaxle, Diagnosis A 0.0 1.8 Notes Includes: Time To Hook-Up And Disconnect Test Equipment. Checking System For Fault Codes, Road Test And Hydraulic Pressure Test As Required. Replace AX4N/4F50N Complete Assembly Without Transfer Of Parts B 5.0 7.3 Notes NOTE To R&R Driveplate, Add B 0.0 0.2 Notes To R&R Torque

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).