Skip to content

how do i time the cams on a 2008 kia rio 1 6

You search PDF repair manual about how do i time the cams on a 2008 kia rio 1 6, if there are search results will appear below. If search results do not exist, please search by others keyword.

2008 TOYOTA RAV4 DOOR SILL ENHANCEMENT REPAIR MANUAL

download
1. Check Kit Content. (a) Check kit for content and damage. (Fig. 1-1) 2. Apply tape. (a) Using the factory door sill plate as a guide, apply tape to the door sill surface at each end of the sill plate as shown. (Fig. 2-1) 3. Remove Factory Door Sill Plates. (a) Using an NRT, Lift the edge of the factory sill plate. (Fig. 3-1) (b) Once the edge of the sill plate has been lifted the plate may be removed by hand by pulling firmly upward. Be sure not to damage the weather strip in the process. (c) Discard the factory door sill plate. Fig. 2-1 Fig. TOYOTA RAV4 2008 – DOOR SILL ENHANCEMENT Procedure Page 3 of 5 pages Issue: A 12/3/07 4. Installation Preparation. (a) Thoroughly clean all installation surfaces. (i) Use a clean lint free cloth. (ii) Clean surface thoroughly using VDC approved cleaner and wipe dry Do allow cleaner to air dry. (Fig. 4-1) (b) Ensure door sill enhancement to be between 70 F and 110 F at time of installation. (c) Ensure vehicle surfaces to be between 70 F and 110 F at time of installation. (d) Do not touch or allow debris or contaminates to come in contact with the adhesive backing before installation. (e) Inspect parts prior to installation. Dry fit parts for alignment reference. 5. Install Front Door Sill Enhancements. (a) Check Part Number label on back of door sill enhancement for applicable side of vehicle, Right Hand or Left Hand and Front or Rear. (b) Position part over vehicle door sill area to check for proper fit and orientation prior to installation. NOTE: The vehicle name logo on the door sill enhancement must be oriented as to be read from the outside of the vehicle. (c) Remove the tape liner from the door sill enhancement. Do not touch the adhesive

2004 Chevrolet Chevy Suburban Information on Gradual Coolant Loss Over Time with No Evidence of Leak Found

download
Some vehicles may experience a gradual coolant loss over time. A very low percentage of cylinder head(s) manufactured with an embossed Castech logo may develop a porosity crack in a very specific area. Inspect the cylinder head assembly to determine if the casting was manufactured by Castech. This can be accomplished by inspecting for their casting logo located on top of the intake port, under the rocker arm support rail and in the spring deck cavity portion of the cylinder head. Important: If the cylinder head(s) are Not a Castech casting, follow normal diagnostic procedures in SI to determine the cause of the coolant loss. Refer to the following illustrations on how to identify Castech casting and/or the very specific areas of the cylinder head(s) for a coolant leak from porosity. If the cylinder head(s) is a Castech casting (1), inspect the area around the five oil drain holes for witness marks indicating coolant seepage over time (2). Important: If No evidence of coolant loss is found on inspection of Castech casting cylinder head (s), follow normal diagnostic procedures in SI to determine the cause of the coolant loss

1984-1995 Honda Accord/Prelude In­Tank Fuel Pumps TEST/REPAIR MANUAL

download
Carbureted Fuel System GENERAL INFORMATION On these vehicles, the engine management system is considered part of the emission control system. The major components include the carburetor(s), feedback control system, the air injection system, a throttle control system and the EGR system. The system consists of sensors and switches that feed information to the Electronic Control Unit (ECU), which will then operate several solenoid valves to maintain the ideal air/fuel ratio under all conditions. As useful as the tests found in this section are, the first step in repair or service to engine management systems is still to gain as much information as possible about the problem; when and under what conditions it occurs. At highway speed? At idle only? Only under heavy load or hard acceleration? Wet weather? Defining the problem will eliminate many systems from consideration and possibly point to the affected system. Before diving into an extended electrical diagnosis, take the time to review the basics. Check every vacuum line for cracks or leaks. Check every electrical connector for corrosion or loose pins. Quite often, simply unplugging and reconnecting a connector will break up corrosion on the pins and restore the circuit. Watch out for poor grounds, particularly if the car has experienced major bodywork. COMPONENT TESTING Air Injection System The purpose of this system is to supply oxygen to the exhaust stream at a point in the exhaust manifold that is hot enough to burn off some of the hydrocarbon emissions. The main component is an air suction valve. The valve is spring loaded to stay closed, with engine vacuum supplied to a diaphragm that reduces the spring pressure and allows the reeds to open. The ECU regulates the engine vacuum to the diaphragm by operating a solenoid valve. 1. With the engine at normal operating temperature and at idle, remove the air cleaner and listen for a bubbling sound at the air suction port. There should be no sound at idle, meaning the air suction valve is closed. 2. If the noise is heard at the air suction port, disconnect the vacuum hose at the air suction valve and connect a vacuum gauge to the hose. There should be no vacuum. If there is vacuum and the noise stops, the problem is in the control system. If there is no vacuum and the bubbling sound is still there, the air suction valve is defective and must be replaced. 3. To test the valve, draw a vacuum at the air suction valve diaphragm and listen for a bubbling sound at the air suction port. If no sound is heard, the air suction valve or diaphragm is faulty. Throttle Control System

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

download
INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.