Skip to content

how do you remove crankshaft pulley from 2002 hyundai santa fe with 2 7

You search PDF repair manual about how do you remove crankshaft pulley from 2002 hyundai santa fe with 2 7, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle

2002 Dodge Neon Power Steering Belt Service and Repair Manual

download
Power Steering Belt REMOVAL POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be removed from power steering pump pulley. Gently, release spring tension on tensioner. 2. Remove the drive belt (Fig. 3). Clean all foreign debris from belt pulley grooves. The belt pulleys must be free of oil, grease, and coolants before installing the drive belt. INSPECTION Belt replacement under any or all of the following conditions is required: ^Excessive wear ^Frayed cords ^Severe glazing Poly-V Belt system may develop minor cracks across the ribbed side (due to reverse bending). These minor cracks are considered normal and acceptable. Parallel cracks are not (Fig. 6). NOTE: Do not use any type of belt dressing or restorer on Poly-V Belts. INSTALLATION NOTE: When installing drive belt on the pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves. POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Install the drive belt (Fig. 3) over all the pulleys except for the power steering pump pulley 2. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be installed on the power steering pulley Release spring tension onto belt. 2002 Dodge Neon L4-2.0L VIN C Copyright © 2009, ALLDATA 9.90 Page 4 3. After belt is installed, inspect belt length indicator marks (Fig. 7). The indicator mark should be within the minimum belt length and maximum belt length marks. On a new belt, the indicator mark should align approximately with the nominal belt length mark

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.