Skip to content

how do you remove electric front seat on 1999 gmc jimmy

You search PDF repair manual about how do you remove electric front seat on 1999 gmc jimmy, if there are search results will appear below. If search results do not exist, please search by others keyword.

FRONT WHEEL SPEED SENSOR CORROSION REPAIR MANUAL

download
1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN 2002 CHEVROLET AVALANCHE 1999-2002 GMC SIERRA 2000-2002 GMC YUKON, YUKON XL LOCATED IN THE SEVERE CORROSION AREAS LISTED BELOW Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. 3. Compress the front brake caliper pistons. 3.1. Install a large C-clamp over the top of the caliper housing and against the back of the outboard pad. 3.2. Slowly tighten the C-clamp until the pistons are pushed completely into the caliper bores. 3.3. Remove the C-clamp from the caliper. Important: It is not necessary to remove the front brake caliper from the bracket when removing the bracket in the next step. 4. Remove the two bolts that attach the front brake caliper mounting brackets to the knuckle. Notice: Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount, and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 5. Remove the brake caliper and bracket as an assembly and support it with heavy mechanic’s wire or equivalent. DO NOT disconnect the hydraulic brake flexible hose from the caliper. 6. Mark the relationship of the rotor to the bearing hub. 7. If equipped, remove the rotor retaining push nuts from the wheel studs

1994 Ford Explorer FRONT WHEEL BEARINGS MANUAL

download
FRONT WHEEL BEARINGS Dana 35-IFS & Automatic Locking Hubs 1. Raise and support vehicle. Remove front wheel assemblies. Remove retaining washers from wheel lug nut studs. See Fig. 1 . 2. Remove automatic locking hub assemblies. Remove snap ring and axle shaft spacer. Carefully pull plastic cam assembly from bearing adjusting nut. Remove 2 plastic thrust washers from adjusting nut. 3. Using magnet, remove locking key from spindle keyway. It may be necessary to rotate adjusting nut slightly to relieve pressure for locking key removal. Loosen adjusting nut with 2 3/8″ Hex Socket (T70T- 4252-B). 4. Tighten adjusting nut to 35 ft. lbs. (47 N.m) while turning hub back and forth to seat bearings. Spin hub and back off adjusting nut 90 degrees. Retighten adjusting nut to 16 INCH lbs. (1.8 N.m). 5. Align nearest hole in adjusting nut with center of spindle keyway slot. If necessary, advance nut to next lug. Install locking key in spindle keyway under adjusting nut. Install 2 thrust washers. Press plastic cam assembly onto adjusting nut while lining up key in fixed cam with spindle keyway. 6. Install axle shaft spacer. Clip snap ring onto end of spindle. Install automatic locking hub assembly with 3 legs of hub assembly inserted into 3 pockets of cam assembly. Install retaining washers and wheel assembly. Check hub and rotor assembly end play. End play should be 0-.003″ (0-.08 mm)

1999 Jaguar XJ8 Vanden Plas SUSPENSION ADJUSTMENTS And Installation Manual

download
ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES HUB BEARING PRELOAD Hub bearing preload is controlled by shim adjustment between hub assembly and hub outer bearing. Shims are available in various thicknesses. Checking 1. Raise and support vehicle. Remove wheel assembly. Clamp dial indicator mount to hub carrier. Ensure dial indicator pointer contacts hub flange. 2. Using 2 levers between hub and hub carrier, press hub outward. Note reading on dial indicator. The difference between dial indicator readings is preload of hub bearing. For adjustment, see HUB CARRIER under REMOVAL & INSTALLATION. REAR SUSPENSION HEIGHT 1. Ensure vehicle has full fuel tank, all fluids are topped off and tire pressures correct. Roll vehicle about 30 feet on a level surface. Measure distance between differential support plate at both sides and ground. See Fig. 2 . 2. Height measurement for coupe and convertible. If height is not within specification, check all bushings and replace as necessary. If bushings are okay, replace rear springs. NOTE: See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. 1999 Jaguar XJ8 Vanden Plas 1999-2000 SUSPENSION’ ‘Rear Fig. 2: Measuring Rear Suspension Height Courtesy of JAGUAR CARS, INC. REMOVAL & INSTALLATION “A” FRAME Removal 1. Raise vehicle and support with stands. Remove “A” frame to final drive unit rear bracket securing bolts and front bracket inner securing nuts and bolts. See Fig. 3 . 2. Position a suitable wood and jack under final drive unit drive flange, operate jack to support final drive unit. Unscrew and remove both “A” frame outer bush to body and bracket securing bolts. See Fig. 4 . Unscrew and remove “A” frame left and right outer bush bracket to body securing bolts. 3. Lower jack approximately one inchto improve access. Unscrew and remove “A” frame to final drive unit front bracket intermediate securing bolts. Unscrew and remove “A” frame to final drive unit fron

Carbon Fiber Seat Heater Installation Instructions

download
Installation Summary – Overview 1. Remove the existing front or rear seat covers. 2. Take note of whether the covers reattach by way of Velcro or Hog rings. 3. The Wire Connector with Purple & Black colored wires is seat the connector which will enable the use of both High & Low temperature functions. 4. Place the heating pads on the seat and at the Listing Reattachment Area mark the pad with a pen. You will be cutting 2 holes per pad. The holes should be equidistant. Example: If your listing length for Velcro or hog rings is 12′ in length then, make a hole at the 4″ & 8″ point. (The Seat Heaters may also be trimmed in length) 5. Now separate the protective adhesive backing at the backside of the heating pads and carefully align your pad and holes with the listing area and press the pads against the seat foam to secure the pad in place. 6. Reinstalling the Covers: Tip: For Backrest Covers, turn the cover inside-out and roll the cover back down the backrest, then reattach the plastic clips. For Seat Bottoms, start by attaching your Velcro or hog ring listings and then proceed to work outwards. Don’t work from front to back or from left to right – start from the middle then work outwards! 7. Switch Location: The diameter of the hole for the switch is 13/16″ or 21mm & the most common location for the switch is on the plastic trim located at the side of the seat. 8. Power Sources: The most common sources are the Accessory Panel, Power Seat, Cigarette Lighter/Accessory Outlet, and Steering Column. However, we recommend drawing power via a relayed key- start trigger sourced directly from the battery. This avoids onboard electronic system interference. ***Warning: If you are installing seat heaters into a vehicle which has a Passenger Side Occupancy Detection System for the Air Bags , You Must Observe The Following: When you remove the seat bottom seat covers, identify whether or not the seat is equipped with topside sensors. They are usually visible and resemble flat circular disks which are interconnected or rectangular in shape. If you are uncertain, you must contact a service department professional for confirmation. Toyota, Kia and Hyundai usually locate the sensors on top of the seat bottom core foam. Honda usually locates the sensors on the face of the seat backrest. In either case, for that particular seat (usually passenger sides only) use only the 2-temp wire connector with one of our seat heater pads. (Disconnect one of the other pads – you will not need it) *The dual temperature wire connector is attached to a black and a purple wire. This will allow dual temperature function with the use of only a single pad

2005 TOYOTA TACOMA PICKUP DASH FRONT DOOR PANEL INSTALLATION MANUAL

download
ANTENNA: THE FACTORY ANTENNA IS LOCATED ATOP THE FRONT PASSENGER FENDER. RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS A DOUBLE DIN OPENING. 1. USING A PICK TOOL, CAREFULLY POP OUT THE A/C CONTROLS. 2. EXTRACT (4) 10MM BOLTS SECURING THE RADIO TO THE DASH, DISCONNECT AND REMOVE. FRONT DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 1/2″ SPEAKER MOUNTED IN A FACTORY ADAPTER. 1. REMOVE “A” TRIM PANEL FROM TOP FRONT CORNER OF DOOR PANEL. 2. EXTRACT (1) PHILLIPS HEAD SCREW FROM DOOR HANDLE. 3. REMOVE ARM REST COVER AND EXTRACT (5) PHILLIPS HEAD SCREWS FROM BEHIND. 4. REMOVE (1) PUSH-TAB FASTENER FROM FRONT UPPER DOOR PANEL NEAR MIRROR. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE. REAR SPEAKER INSTALLATION: NOTE: 2-DOOR REGULAR CAB HAS NO FACTORY REAR SPEAKER PROVISION. EXTENDED CAB REAR-SIDE DOOR SPEAKER INSTALLATION: 1. REMOVE (1) PHILLIPS HEAD SCREW FROM DOOR HANDLE, THEN REMOVE HANDLE COVER. 2. REMOVE (1) PHILLIPS FROM ARMREST POCKET. 3. REMOVE (1) POP TAB AT THE TOP OF THE DOOR PANEL. 4. REMOVE (1) 15 MM BOLT SECURING SEAT BELT TO BOTTOM OF THE DOOR. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE. 4-DOOR CREW-CAB REAR SIDE DOOR SPEAKER INSTALLATION: 1. REMOVE (1) PHILLIPS HEAD SCREW FROM DOOR RELEASE HANDLE. 2. REMOVE (1) PHILLIPS FROM ARMREST POCKET. 3. REMOVE TRIM PANEL ON REAR SIDE OF WINDOW. 4. REMOVE (1) PUSH-TAP FASTENER EXPOSED IN STEP #3 ABOVE. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY, UNPLUG CONNECTORS AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE.