Skip to content

how do you test a 4 wheel drive actuator

You search PDF repair manual about how do you test a 4 wheel drive actuator, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 – 2007 NISSAN MAXIMA ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON

download
IF YOU CONFIRM The ABS light is ON with one or more of the following DTC stored, • C1105 – RR RH Sensor 2 • C1110 – Controller Failure • C1124 – RR LH IN ABS SOL • C1126 – RR RH IN ABS SOL and/or The ABS system activates with normal braking. ACTIONS 1. Remove only the right rear brake rotor, wheel hub assembly, baffle plate and ABS wheel sensor. 2. Clean the corrosion off of the knuckle, wheel hub assembly, and baffle plate. 3. Grind a notch in the knuckle locating hole (locating hole for plastic hub cap). 4. Reassemble using the new plastic hub cap and a new ABS wheel sensor. 5. If code C1126 and/or C1124 is stored; replace the ABS actuator. 6. Test drive vehicle; recheck for code C1110 (refer to step 10 in the Service Procedure). IMPORTANT: The purpose of “ACTIONS” (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure (starting on page 2) as it contains information that is essential to successfully completing the repair PARTS INFORMATION DESCRIPTION PART # QUANTITY Sensor Assy – Anti Skid Rear 47900-7Y000 1 Cap-Hub – RH 43234-ZK30A 1 ABS Actuator Use the VIN and the electronic parts catalog (FAST or equivalent) to find the correct P/N 1 (if needed) CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODESYM DIA FRT RPL Rear ABS Sensor and Plastic Hub Cap (1) PX32AA ZE 32 1.1 (1) Reference the FAST Parts Catalog and use the “Housing Assy – Rear Axle, RH” P/N as the PFP. And, IF Necessary, use Combination Op Code: DESCRIPTION OP CODE FRT RPL ABS Actuator PX321A 1.5 SERVICE PROCEDURE 1. Remove only the right rear (passenger side) brake rotor, wheel hub assembly, and baffle plate (see Figure 1). • Refer to Section RAX in the Service Manual for removal information

2009 Cadillac CTS AWD Front Wheel Drive Shaft Replacement – Left Side

download
Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle ( See: Maintenance\Vehicle Lifting\Service and Repair ). 2. Remove the left front tire and wheel. Refer to Tire and Wheel Removal and Installation ( See: Maintenance\Wheels and Tires\Service and Repair ). 3. Remove the left outer tie rod from the steering knuckle. Refer to Steering Linkage Outer Tie Rod Replacement (All Wheel Drive) ( See: Steering and Suspension\Steering\Tie Rod\Service and Repair\Steering Linkage Outer Tie Rod Replacement )Steering Linkage Outer Tie Rod Replacement (Rear Wheel Drive) ( See: Steering and Suspension\Steering\Tie Rod\Service and Repair\Steering Linkage Outer Tie Rod Replacement ). 1. Install the new O-ring (2) on the intermediate shaft. 2. Install the new retaining ring (1) on the intermediate shaft. 3. Apply a small amount of grease GM P/N 01051344 (Canadian P/N 993037) or equivalent to the intermediate wheel drive shaft splines. 4. Install the left front wheel drive shaft in the intermediate shaft. 5. To ensure that the wheel drive shaft is installed properly, grasp the inner tripod housing and pulling it outward. DO NOT pull on the axle shaft . 6. Install the wheel drive shaft in the front knuckle. 7. Install the left upper control arm on the knuckle. Refer to Upper Control Arm Replacement ( See: Steering and Suspension\Suspension\Control Arm\Service and Repair\Rear Suspension\Upper Control Arm Replacement

1989 Nissan Pickup (200SX & 300ZX) TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal (200SX & 300ZX) 1. Disconnect negative battery cable. Release fuel pressure from system. Raise and support vehicle. Remove right wheel and engine side cover (if necessary). Drain cooling system. Remove cooling fan duct. Remove engine coolant reservoir. Remove actuator and remove radiator hoses. Do not allow coolant to contact drive belts. 2. Remove front upper and lower belt covers. See Fig. 1 . Remove drive belts and set No. 1 cylinder at TDC of compression stroke. Remove idler bracket of compressor drive belt and crankshaft pulley. Remove timing belt by removing timing belt tensioner and return spring Inspection (200SX & 300ZX) Visually inspect condition of timing belt. Inspect for cracks, wear, breaks, and oil/coolant saturation. Installation (200SX & 300ZX) 1. Ensure that piston No. 1 is at TDC of compression stroke. Remove valve covers and loosen all rocker shaft bolts. Do not bend timing belt. Install tensioner and return spring. 2. Turn tensioner clockwise and temporarily tighten lock nut. Install timing belt. Align White lines on timing belt with punch mark on camshaft pulleys and crankshaft pulley. Arrow on timing belt must be pointing toward front belt covers. 3. Using Allen wrench, slowly turn tensioner clockwise and counterclockwise 2 or 3 times. When camshafts and crankshaft marks are aligned, tighten tensioner lock nut. See Fig. 2 . Ensure that camshaft lobes are correctly positioned. Tighten rocker shaft bolts in 2 stages. 4. Refill and bleed air from cooling system. To complete installation, reverse removal procedures. Adjust drive belts to proper tension

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).