tight make camshaft bolts explorer sohc

You search PDF repair manual about tight make camshaft bolts explorer sohc, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tight make camshaft bolts explorer sohc Direct Download speed 5432 Kb/s

  tight make camshaft bolts explorer sohc Full Version speed 8172 Kb/s



3406E TRUCK ENGINE 2WS Camshaft Gear Removal And Installation Manual

0

Filed Under (More Manuals) by admin on 28-05-2012

download
1. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 2. Remove top bolt (2) from camshaft gear (1) . Install Tooling (A) in place of the bolt. 3. Remove remaining bolts (2) and remove camshaft gear (1) . 4. NOTICE Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. Remove Tooling (A) . 5. Installation Procedure Required Tools Tool Part Number Part Description Qty A 9U-6896 Guide Bolt 1. Align the hole in the back of camshaft gear (1) with the dowel in the adapter. Install camshaft gear (1) over Tooling (A) . Note: Camshaft timing is critical. The timing mark on the camshaft gear must be aligned with the timing mark on the front cover when the No. 1 piston is at the top center of the compression stroke. Refer to Testing and Adjusting, “Gear Group (Front) – Time”. Verify that the timing mark on camshaft gear (1) is aligned with Timing Mark (X) on front housing (3) . 3. Note: If the timing marks are not aligned, remove camshaft gear (1) and rotate the camshaft until the timing marks are aligned. Install bolts (2) . Remove Tooling (A) and install remaining bolt (2) . 4. 5. Check the backlash between the camshaft gear and the adjustable idler gear. The backlash should be 0.216 ± 0.114 mm (0.0085 ± 0.0045 inch). Refer to Testing and Adjusting, “Gear Group (Front) – Time” for the backlash adjustment procedure. 6. End By: Install the front cover. Refer to Disassembly and Assembly, “Front Cover – Install”

Related Content:

volvo s40 cam alignment instructions, 3406e front cover removal, 3406e timing gear backlash, c15 cam gear backlash, c15 cat cam to idler gear backlash, Cat C15 rotation, mazda timing marks 1991 mx6

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

0

Filed Under (Toyota Manuals) by admin on 27-04-2012

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

Related Content:

2008 saturn vue v6 camshaft position actuator solenoid location, toyota 1g engine manual, toyota 1g fe vvt-i engine service manual, torque settings for toyota 1g fe, www pdfrepairmanual com/search/toyota 1g fe engine, toyota 1g-fe workshop manual, crank shaft torque specs 2000 passat 2 8 30valve v6, 1gfe timing marks, 06 Mazda 6 DTC p1349, 1g-fe camshaft timing marks /pdf

1999 Honda Civic EX TORQUE SPECIFICATIONS

0

Filed Under (Honda Manuals) by admin on 04-02-2012

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Related Content:

pontiac vibe head torque secuensia, 1999 honda civic door bolt torque specifications, tork settings for fd 42 engine, nuts&bolts service, nissan fd42 tuning, j35 honda bolt pattern transmission, how to rebuild a saturn 1 9 sohc, honda generator bolt torque spec, head bolt torque specifications 2000 buick century, fd42 manifold gasket

1997 Saturn SL2 FRONT COVER And TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 10-05-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. Put a block of wood between cradle and engine torque strut at bottom front end of engine. See Fig. 2 . 2. Remove mount from upper front end of engine, allowing engine to rest on wood block. Remove accessory drive belt and tensioner. Remove accessory belt idler. Remove cylinder head cover. 3. Replace silicone isolators on cylinder head cover screws if deteriorated. Remove power steering pump (leave hoses attached). Remove A/C compressor (leave hoses attached). Raise and support vehicle. Drain engine oil. Remove right front wheel and splash shield. 4. Remove support bracket between intake manifold and engine block. Remove front balancer/pulley using a 3-jaw puller. Disconnect exhaust pipe from exhaust manifold. Install Crankshaft Gear Retainer (SA9104E) onto end of crankshaft, with flat side toward crankshaft gear (sprocket). Crankshaft gear retainer holds crankshaft gear in place during removal of front cover. 5. Remove 4 bolts from front end of oil pan. Using RTV Cutter (SA9123E), cut RTV sealant between oil pan and front cover. Spray penetrating oil onto front cover dowel pins. Remove front cover bolts (one bolt is located above accessory drive belt pulley). Pry front cover from engine block. 6. To prevent pistons from hitting valves, turn crankshaft 90 degrees clockwise as viewed from front of engine until timing mark and keyway are aligned with split line of main bearing cap. Remove timing chain tensioner, guides and chain. While using a 7/8″ (21 mm) wrench to keep camshaft(s) from turning, remove camshaft sprocket bolt(s). Remove camshaft sprocket(s). Installation 1. To prevent pistons from hitting valves, ensure timing mark and keyway on crankshaft are aligned with split line of main bearing cap. Install camshaft sprocket(s) with the letters FRT (front) facing away from cylinder head. Use a 7/8″ (21 mm) wrench to keep camshaft(s) from turning. 2. Install and tighten camshaft sprocket bolt(s) to specification. Rotate camshaft(s) until a 3/16″ (4.8 mm) drill bit can be inserted through timing pin hole(s) and into cylinder head. See Fig. 5 or Fig. 6 . 3. Rotate crankshaft counterclockwise as viewed from front of engine until timing marks at crankshaft sprocket are aligned. Install timing chain, aligning Silver-plated chain links with timing mark(s) on camshaft sprocket(s) and bottom tooth (or teeth) of crankshaft sprocket. See Fig. 5 or Fig. 6 . 4. Install fixed chain guide. Slack part of chain should be on tensioner side of cylinder block. Chain should be tight against fixed chain guide. Install pivoting chain guide. Retract tensioner plunger, and pin ratchet

Related Content:

1997 saturn manifold repair, 2000 lexus es 300 gear sprocket, 2007 SATURN RELAY 3 9 V6 TIMING CHAIN/ MAGNETIC SPROCKET

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

1994 Mitsubishi Expo LRV TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 30-04-2012

download
Removal 1. Remove radiator shroud, cooling fan and pulley. Remove all drive belts and crankshaft pulleys. Remove upper timing belt covers and gaskets. Note bolt length and location. 2. Remove crankshaft sprocket bolt and washer. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with mark on cylinder head. See Fig. 5 . 3. Loosen timing belt tensioner adjustment bolt, and move tensioner toward water pump. Tighten bolt to secure tensioner. Remove front timing belt and tensioner. DO NOT rotate crankshaft after timing belt has been removed. 4. Remove camshaft sprocket (if necessary). Remove oil pump sprocket access plug from cylinder block. See Fig. 4 . Insert a .31″ (8.0 mm) diameter Phillips screwdriver to block left silent shaft. 5. Remove oil pump sprocket nut, and remove sprocket. Remove front crankshaft sprocket and flange. Note direction and order of installation for reassembly reference. 6. Remove rear timing belt tensioner assembly. Remove rear timing belt. Remove right silent shaft sprocket with spacer (if necessary). Remove rear crankshaft sprocket with key Installation 1. Install rear crankshaft sprocket and flange. Install right silent shaft sprocket and spacer. Spacer should be installed with chamfered end into oil seal. Align timing marks. See Fig. 5 . 2. Install rear tensioner. Hold tensioner tightly against belt while tightening bolts. Ensure deflection is .20- .28″ (5.0-7.1 mm). See Fig. 6 . Install camshaft sprocket. Tighten camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS . 3. Install front timing belt tensioner, tension spring and spacer. Ensure spring is properly engaged against water pump case. Rotate tensioner toward water pump, and temporarily tighten bolts. Ensure timing marks are aligned. See Fig. 5 . Install timing belt on crankshaft. 4. Apply pressure on tension side of timing belt while installing belt (in order) on crankshaft, oil pump and camshaft sprockets. Loosen tensioner to apply spring pressure to timing belt. 5. To apply tension to belt, rotate crankshaft clockwise until camshaft sprocket timing mark is offset by 2 teeth. Tighten tensioner bolt. Tighten tensioner spacer nut

Related Content:

04 volvo s60 2 5t how to align cam shafts to cam sprockets, adjusting cam sprockets, chrysler sprocket removal tool, ej25d enigine TORQUE, what are torque values for 2 2ecotec cam sprokets

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 04-05-2012

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

Related Content:

yhow to remove and install airbag for fored explorer sport trac, 2001 Sport Trac Manual Download, 2005 ford explorer code c2769, how to replace thermostat housing on 2003 ford sport trac 3 6liter, location of the GEM module 02 explorer, lube points on a 1997 thunderbird, overhead console sport trac fix, p0741 explorer 5r55e, rear window wont go up connector in sill plate 05 ram, remove rear pillar camry

2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation Instructions

0

Filed Under (Honda Manuals) by admin on 22-01-2011

download
1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head. -1 Drive pulley (A). -2 Tensioner pulley (B). -3 Water pump pulley (C). -4 Camshaft pulley (D). 6. Loosen and retighten the adjusting nut to tension the timing belt. 7. Clean any oil off both faces of the balancer belt drive pulley. 8. Check the lower cover rubber seal for cracks and other damage. NOTE: ?If the rubber seal is coming off, apply liquid gasket to the lower cover and reinstall the rubber seal. Wipe off any liquid gasket that is pressed out. ?When replacing the rubber seal, clean the lower cover groove, cut the repair rubber seal to length, and put the rubber seal into the groove evenly. 9. Install the balancer belt drive pulley and the lower cover. 10. Temporarly install the crankshaft pulley and bolt. 11. Rotate the crankshaft pulley five or six turns counterclockwise to seat the timing belt on the pulleys. 14. Check the camshaft pulley marks. ?If the camshaft pulley marks are also at TDC, go to step 15. ?If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 3, 4 and 5. 15. Remove the crankshaft pulley and the lower cover. 16. Turn the crankshaft to TDC again. 17. Lock the timing belt adjuster arm in place with one of the 6 mm timing cover bolts. 18. Loosen the adjusting nut 2/3-1 turn, and make sure the balancer belt tensioner moves freely. Then push the tensioner up and retighten the adjusting nut. 19. Align the rear balancer shaft pulley with a 6 x 100 mm bolt (or equivalent). -1 Remove the bolt (A) and washer (B) from the maintenance hole (C). -2 Scribe a line on a 6 x 100 mm bolt, 74 mm (2.9 in) from the end

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, toyota2y engine only starts when rocker shaft has been loosened, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, 2003 buick lasabre serpentine belt idler pulley torque spec, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys, lincoln ls crank pulley diagram

Toyota Starlet Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 15-01-2012

download
Removal Removal Raise and support front of vehicle. 1. Support engine. 2. Remove: RH front wheel. Inner wing panel. Engine mounting and bracket. Auxiliary drive belt(s). Cylinder head cover. Timing belt upper cover [1] . 3. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure crankshaft pulley timing mark aligned [2] . 4. Check hole in camshaft sprocket aligned with mark on camshaft bearing cap [3] . 5. If not: Turn crankshaft one turn clockwise. 6. Remove: Crankshaft pulley bolt [4] . Use tool Nos.09213-14010 & 09330-00021. Crankshaft pulley [5] . Use tool No.09213-31021. Timing belt lower cover [6] . 7. Temporarily fit crankshaft pulley bolt [4] . 8. Ensure timing marks aligned [3] & [7] . 9. Slacken tensioner bolt [8] . Move tensioner away from belt and lightly tighten bolt. 10. Remove: Timing belt. Tensioner pulley and spring [9] & [10] . 11. Installation Installation Check tensioner pulley for smooth operation [9] . 1. Check free length of tensioner spring is 38,4 mm [10] . 2. Fit tensioner and spring. Ensure spring is connected correctly. 3. Push tensioner to left and lightly tighten bolt [8] . 4. Ensure timing marks aligned [3] & [7] . 5. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 6. Slacken tensioner bolt [8] . 7. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [3] & [7] . 8. If not: Repeat installation and tensioning procedures. 9. Tighten tensioner bolt [8] . Tightening torque: 19 Nm. 10. Remove crankshaft pulley bolt [4] . 11. Install: Timing belt lower cover [6] . Crankshaft pulley [5] . 12. Install components in reverse order of removal. 13. Tighten crankshaft pulley bolt [4] . Tightening torque: 152 Nm. Use tool Nos.09213-14010 & 09330-00021. 14.

Related Content:

1999 toyota camry crankshaft bolt direction, can I replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?

Ford V8 Engines Performer RPM Hydraulic Roller Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 01-01-2012

download
Disconnect the battery. 2. Drain radiator coolant. Drain plug will normally be located on lower right or left side of the radiator facing the engine. 3. Remove radiator and air conditioning condenser if so equipped. In some cases, the front grill may have to be removed. Measure distance from front cover to grill or brackets that may interfere with camshaft against the length of the camshaft. 4. Remove the gas cap to relieve pressure. Disconnect fuel line and plug. Replace gas cap. 5. Disconnect all linkage from carburetor such as throttle, throttle springs, transmission, cruise control and automatic choke. 6. Tag and remove coil wires and sensor wires. 7. Tag and remove vacuum lines. 8. Remove valve covers. 9. Remove distributor cap and wires, rotate engine until rotor points towards number 1 terminal in cap and pointer on front cover is on top dead center (TDC) and remove distributor. (see Fig. 1) Note: Mark the approximate position of the distributor housing in relation to the manifold to assist in getting the distributor properly located during re-installation. 10. Remove carburetor and intake manifold. Remove and discard intake manifold gasket. 11. Remove rocker arms and pushrods. CAUTION: If your engine has non-adjustable rocker arms (1969-1/2 or later), you must install screw-in studs and high performance •VALVE SPRINGS CAUTION: WARNINGS ABOUT YOUR WARRANTY In order for this Performer RPM roller cam to be covered under ANY WARRANTY, you MUST use the correct Valve Springs. Failure to install the correct valve springs may cause lifters not to follow the cam lobes and damage engine parts. This camshaft is designed to function with valve springs that have a closed pressure of 110 lbs, open pressure of 320 lbs and a lift of .575″. Special H.P. retainers may be necessary with your installation for proper spring height. Do not use rotator type valve springs or retainers for this application. Note: Edelbrock Sure Seat Valve Springs #5762 are not recommended.  IMPORTANT NOTES AFFECTING YOUR WARRANTY CAM LOBE DAMAGE – Cam lobe wear is almost non-existent unless mismatched parts are used or installation of the cam and lifters is done improperly. Cam damage can result from the timing gear loosening due to improper torque on bolts. Bolts holding gear to camshaft should be torqued carefully and a locking compound applied to threads of bolts. Before installing your new Performer-RPM roller camshaft, check the gear drive on the distributor and oil pump for any signs of wear. If worn, be sure to replace with a new gear or you may wear out your camshaft prematurely. High-pressure oil pumps are not recommended with Performer RPM roller camshafts. Edelbrock camshafts are designed to use with Edelbrock timing chains.  CAM GEARS AND CAMSHAFT END PLAY- If cam gear becomes loose, the cam will slide back in the block, causing the lifters to hit the lobes next to them and also the cam bearing journals. If the engine is run after this happens, the bottom of the lifters and the sides of the lobes will become damaged. See Installation Instructions section for end play specifications.  LIFTERS Edelbrock offers a retrofit roller lifter kit for engines not originally equipped with roller lifters. Use part #97453. To install your roller lifters, use fresh clean oil on the lifter and the lifter bore just prior to installing. The guide bar (high side of tappet) must face the opposite side of block. See roller lifter instructions for additional information. ( Note: 289-302 engines require removal of the cylinder heads to provide enough clearance to install roller lifters, which are taller than standard hydraulic lifters.)  PUSHRODS AND ROCKER ARMS High performance pushrods, roller rocker arms and rocker studs are recommended for this installation. After the cam is installed and timed correctly (see Figure 2), it will be necessary to check each pushrod for correct lifter preload. INSTALLATION INSTRUCTIONS 1. Check lifters as covered in Lifters section. Coat cam lobes with fresh clean oil. Lube distributor drive of cam with assembly lube (supplied). 2. Install new camshaft. Re-install thrust plate with new sprockets and timing chain with timing marks lined up as recommended by factory specifications (See Figure 2). Reinstall the fuel pump eccentric before installing sprocket bolt and washer

Related Content:

roller lifters trouble 2010 gmc, 2006 DT466 lifters, torque side trrminal battery, sun distributer machines parts, rear cam bolt torque 4 0 sohc, mitsubishi 4g13 series wiring diagram manual, ford 302 camshaft endplay, Ford 2003 4 liter V6 camshaaft bolt torque, 5 3 camshaft problems, v6 3000 four cam 24 vvt-i thermostat location

Related Content:

volvo s40 cam alignment instructions, 3406e front cover removal, 3406e timing gear backlash, c15 cam gear backlash, c15 cat cam to idler gear backlash, Cat C15 rotation, mazda timing marks 1991 mx6