how to adjust minium idle on 98 olds silhouette

You search PDF repair manual about how to adjust minium idle on 98 olds silhouette, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to adjust minium idle on 98 olds silhouette Direct Download speed 5432 Kb/s

  how to adjust minium idle on 98 olds silhouette Full Version speed 8172 Kb/s



1994 Ford Explorer FRONT WHEEL BEARINGS MANUAL

0

Filed Under (Ford Manuals) by admin on 08-07-2012

download
FRONT WHEEL BEARINGS Dana 35-IFS & Automatic Locking Hubs 1. Raise and support vehicle. Remove front wheel assemblies. Remove retaining washers from wheel lug nut studs. See Fig. 1 . 2. Remove automatic locking hub assemblies. Remove snap ring and axle shaft spacer. Carefully pull plastic cam assembly from bearing adjusting nut. Remove 2 plastic thrust washers from adjusting nut. 3. Using magnet, remove locking key from spindle keyway. It may be necessary to rotate adjusting nut slightly to relieve pressure for locking key removal. Loosen adjusting nut with 2 3/8″ Hex Socket (T70T- 4252-B). 4. Tighten adjusting nut to 35 ft. lbs. (47 N.m) while turning hub back and forth to seat bearings. Spin hub and back off adjusting nut 90 degrees. Retighten adjusting nut to 16 INCH lbs. (1.8 N.m). 5. Align nearest hole in adjusting nut with center of spindle keyway slot. If necessary, advance nut to next lug. Install locking key in spindle keyway under adjusting nut. Install 2 thrust washers. Press plastic cam assembly onto adjusting nut while lining up key in fixed cam with spindle keyway. 6. Install axle shaft spacer. Clip snap ring onto end of spindle. Install automatic locking hub assembly with 3 legs of hub assembly inserted into 3 pockets of cam assembly. Install retaining washers and wheel assembly. Check hub and rotor assembly end play. End play should be 0-.003″ (0-.08 mm)

Related Content:

Webasto Sunroof Adjustment, 08 uplander axle nut size, 08 uplander axle nut socket size, 2008 flhrc front axle torque, 4g13 connecting rod tension in foot pounds, cummins l10 runs rough and smokes, install* Ford ratchet nut, lazy boy recliner adjustment, What size nut is on the spindle of a 2004 Yukon

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

vacuum connection for kancil, 4g13 engine ignition adjustments, stock primary and secondary jettings 4af toyota, specialist kancil carburetor, setting caburater kancil, schematic diagram of elect fuel system include locations for a 1989 toyota camry 2 0 engine passenger car, kancil overhaul module, kancil carburetor tuning, kancil carburetor air fuel ratio screw, how to change kancil carburetor

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 02-01-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

iS THERE A SPRING CONNECTING THE LINKAGE TO THE TPS ON A97 LESABRE, edelbrock dubble carburetor adjustment linkage, relearn on throttle body trailblazer 2005, throttle body for a 2006 buick rendezvous, relearn procedure for throttle body 2004 chevy trailblazer, volvo penta throttle control diagram, p1512 chevy trailblazer, lincoln ls throttle linkage, where is the fuel line to throttle body on a 2006 KIA RIO, jaguar s type throttle body return spring

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Related Content:

4efe head bolt torque foot pounds, 4g13 timing marks, free 4g13 engine and distributor timing, free download Service Manual for a 1992 Toyota Truck, Toyota 5K ignition, _1987_Nissan_pickup_v6 destributer timing marks

1984 Mercedes Benz 190E Fuel Delivery and Air Induction Engine Testing And Adjustment Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 13-04-2012

download
Note: Test and adjust lambda control with a lambda control tester. The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer. Testing, adjusting 1 Complete measurement sheet. 2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”. 3 Read out DTC memory. Note: Not available on model year 1984-1986. 4 Connect testers: oil remote thermometer (018)124 589 07 21 00 lambda control tester (012) twin socket (031) trigger clamp (011) exhaust probe (005)126 589 11 63 00 CO measuring instrument (006) engine tester with oscilloscope (030) multimeter (003) test cable (033)102 589 04 63 00. 5 Position extraction device (014) at exhaust tail pipe. 6 Check engine coolant level, adjust to correct level. 7 Check engine oil level, pay attention to condition of oil (visual inspection). 8 Take off air cleaner. 9 Check ease of movement and condition of throttle control linkage and throttle valve. Grease all bearing points and ball sockets. 10 Check fulcrum lever, adjust. Check whether the roller (15) in the fulcrum lever (13) is resting free of tension against end stop. Adjust fulcrum lever (13) with the connecting rod (2), if necessary, so that the roller (15) is resting free of tension against end stop. 11 Idle stop. Check whether the throttle valve is resting against idle stop. Disconnect connecting rod (2) for this step. Adjust throttle control. Engines with cruise control only. Check whether the actuator is resting against idle stop of cruise control by pressing the lever of the actuator clockwise against idle stop at cruise control. When attaching the connecting rod (21), ensure that the lever of the actuator is lifted approx. 1 mm off the idle stop at the cruise control. Adjust tie rod, if necessary. Adjust throttle control. 12 Check wide open throttle stop from the accelerator pedal , adjust. 13 Voltages Test (battery and ignition coil ): No-load voltage Connect voltmeter to the battery, paying attention to the polarity, and take reading of voltage. Specification: 12.2 volts . Ignition coil Switch on ignition with engine not running. Test the voltage terminal 15 to ground at contact 5 of diagnostic connector. Specification: battery voltage Test difference in voltage between terminal 15 and terminal 1 at contacts 5 and 4 of diagnostic connector. Specification: 0 volts If the specified values are not reached, test

Related Content:

throttle control motor relay 05 mazda 3, 1986 190e 2 3 crank trigger test, 2007 Dodge Throttle Valve Actuator Installation Instructions, ax4n endplay pdf, carborator for mazda6 2003 manual gear, how to test actuator of stabilator, how to test throttle actuator motor, mb 1993 lamda code, throttle position sensor 1986 190e 16 valve

1997 Jeep Cherokee 2WD Serpentine Belt INSPECTION ADJUSTMENT REMOVAL And INSTALLATION

0

Filed Under (Jeep Manuals) by admin on 05-01-2012

download
INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure. Loosen the pump upper pivot bolt, lower locknut and pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 1. Use a belt tension gauge placed in the middle of the belt being tested. Proper tension for a new belt is 180-200 lbs. (800-900 N) and 140-160 lbs. (623-712 N) for a used belt. 2. Tighten the pump adjusting bolt to achieve proper tension and recheck the belt tension. 3. Fig. Fig. 1: Loosen the pivot bolt (1), then the locking bolt (2) to loosen the power steering pump from behind Fig. Fig. 2: Use a ratchet and 13mm size socket to rotate the power steering pump Fig. Fig. 3: Adjustment points on the 2.5L engines without power steering (rear view) Fig. Fig. 4: Adjustment points on the 2.5L engine (front view) Removal & Installation 2.5L and 4.0L Engines With Power Steering See Figures 5, 6 and 7 Fig. Fig. 5: Proper belt routing diagram can usually be found on a sticker located in the engine compartment Fig. Fig. 6: Common 4.0L engine serpentine belt routing Fig. Fig. 7: Common 2.5L engine serpentine belt routing Loosen the rear power steering pump mounting bolts using a ratchet and 13mm socket or a 13mm box wrench. 1. Loosen the pump upper pivot bolt, lower locknut and the pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 2. Remove the belt. 3. To install: Install the belt. 4. Tighten the pump adjusting bolt to achieve proper tension. 5. Install the pump rear mounting bolts, pivot bolt and locknut. Tighten the bolts to 20. ft. lbs. (27 Nm). 6. Check the belt for proper tension. If tension is incorrect, refer to the adjustment procedure in this section. 7. 5.2L and 5.9L Engines See Figures 8, 9 and 10

Related Content:

1986 jeep cherokee serpentine belt route, serpintin belt diagram for 2006 jetta, kia 3 5 crank bolt for sale, jetta 2006 fan belt totation, GM 10 Bolt Rebuild Manual, gm 10 bolt instructions, 99 Jeep Cherokee Owners Manual pdf, 2010 Kia Forte Serpentine Routing Belt Diagram, 2004 honda civic serpentine belt, 1995 Jeep 2 5L ccv orfice and emissions

1998 Ford Escort ZX2 L4-2.0L DOHC Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 06-05-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1). 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) 10. Remove original front and rear engine support cross-member bushings (Figure 3). Zoom Sized for Print a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.)

Related Content:

2004 chevy colorado 3 5 camshaft actuator, 2002 ford escort manual pdf

1998 Ford Escort Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 30-04-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1) 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.).

Related Content:

rotunda three bar engine support

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

0

Filed Under (Kia Motors Manuals) by admin on 11-01-2012

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

Related Content:

how to adjust a cat forklift throttle position sensor, how to check 2006 G6 throttle sensor, kia sorento throttle position sensor, 2008 silverado replace tps, 2006 kia amanti idle speed adjustment, tsb kia sedona p0765, p0087 kia sorento, replace throttle body sensor ford escape, Where is the electronic throttle control relay for a 2008 trail blazer, replaced throttle body new on my 2004 saturn vue and ligjt still comes on and off

Toyota Corolla DVD GPS Navigation Installation Manual

0

Filed Under (Toyota Manuals) by admin on 05-12-2011

download
onvulsed timbre and enjoy all your journey! Auto-memory function As you must stop the DVD or CD display to switch other interface, auto-memory function will keep the currently information, as your back entertainment system, it can display on top of the stop point automatically. Convulsed timbre and topping enjoy! Four channel outputs, built-in 4 HI-FI amplifiers, presentinga perfect audio and video quality, The sound combining with scene can give you a surprising surround stereoscopic feeling! External car amplifier External car amplifier can be connected to achieve higher request! Entire function control: Entire function control: Entire function control: Entire function control: Through the touch screen, iPodfunctionscan be operated such as play, pause,stop,next, previous, categorize by singer, album, or random playing. Song title display: Song title display: Song title display: Song title display: Contents in the iPod can be displayed like song titles, playing status, time, etc.It is like displaying all the contents of the iPod into the touch screen. The song titles can be in Traditional Chinese, Simplified Chinese,Japanese, English,etc. Timber adjust: Timber adjust: Timber adjust: Timber adjust: As connecting IP od and displaying the song, the timber adjust function can advance the sound effect of I pod. Bluetoothhands-free car kit Bluetoothhands-free car kit Bluetoothhands-free car kit Bluetoothhands-free car kit supportbluetooth hands-free; Auto-distinguish mobile without connection or mobile bracket; you can dial the tele number in the display; the call volume can be adjusted; Auto-storage the incoming telegrams and dial numbers; storage 3partnership mobile Audio EchoClear-Up Audio EchoClear-Up Audio EchoClear-Up Audio EchoClear-Up AEC isonekindof outlying signal voice model, which bases on the pertinence of speaker signal and multipath echo coursed by speaker. We can evaluate the echo by AEC model?and amend the filter parameters continual to make the guesstimate near the true echo. Then takeout the echo guesstimate from the micro input signal to eliminate the echo and realize the perfect hands-free calling

Related Content:

1997 Lincoln Repair Manual Free, free 1986 corvette owners manual, Robinair 17400 Manual, scion xb repair manual download, 1992 corvette owners manual, rover p6 free workshop manual downloads, c4 corvette battery cable replacement instructions, installation of 1999 lincoln town car radiator, mute wrire 2001chv impala, gmc envoy 2002 owners manual mobile

Related Content:

Webasto Sunroof Adjustment, 08 uplander axle nut size, 08 uplander axle nut socket size, 2008 flhrc front axle torque, 4g13 connecting rod tension in foot pounds, cummins l10 runs rough and smokes, install* Ford ratchet nut, lazy boy recliner adjustment, What size nut is on the spindle of a 2004 Yukon