Skip to content

how to change a 2004 chevrolet cavalier heater blend door actuator

You search PDF repair manual about how to change a 2004 chevrolet cavalier heater blend door actuator, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.